Chery Tiggo 5 (T21). Service manual — part 60
06–
82
06
DTC Confirmation Procedure
Confirm that battery voltage is over 12 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
Turn ignition switch to ON.
Use X-431 3G diagnostic tester to record and clear the DTCs stored in the ECM.
Select Read Code.
If the DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis
procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent (
).
Diagnosis Procedure
a. Turn ignition switch to LOCK.
b. Check ECM grounds E-026 and E-028 (
a. Disconnect injector connector E-010 of cylinder 1.
b. Check injector connector.
DTC Code
DTC Definitions
DTC Detection
Conditions
Possible Cause
P0201-00
Cylinder 1 - Injector
Circuit
Engine running
Injector of cylinder 1
Wire harness or connector
ECM
CAUTION
When performing circuit diagnosis and test, always refer to the circuit diagram for specific circuit and
component information.
1
Check ECM ground point
Repair or replace ground wire harness or
ground point
NG
2
Check injector connector of cylinder 1
OK
RT21060150
Repair or replace connector
NG
06–
83
06
a. Disconnect injector connector E-010 of cylinder 1.
b. Turn ignition switch to ON.
c. Check voltage between injector connector terminal of
cylinder 1 and body ground.
a. Turn ignition switch to LOCK.
b. Check fuse EF08 and main relay.
c. Disconnect engine compartment fuse and relay box
connector E-023.
d. Check wire harness between injector connector terminals
and engine compartment fuse and relay box connector
terminals.
Check for Open
3
Check injector power supply voltage of cylinder 1
OK
E-010
1
2
-
+
V
RT21065031
Multimeter
Connection
Condition
Specified
Condition
E-010 (1) - Body
ground
Ignition switch ON
11 to 14 V
Go to step 5
OK
4
Check injector power supply circuit of cylinder 1
NG
E-010
E-023
1
2
C1
C2
C3 C4
C5
C6
C7
C8 C9 C10
-
+
RT21065032
Multimeter
Connection
Condition
Specified
Condition
E-010 (1) - E-023
(C3)
Always
Continuity
06–
84
06
Check for Short
a. Disconnect ECM connector E-035.
b. Check wire harness between injector connector terminals
and ECM connector terminals.
Check for Open
Check for Short
Multimeter
Connection
Condition
Specified
Condition
E-010 (1) or
E-023 (C3) - Body
ground
Always
No continuity
E-010 (1) or
E-023 (C3) -
Battery positive
Repair or replace wire harness or
connector (injector of cylinder 1 - engine
compartment fuse and relay box)
NG
5
Check injector control circuit of cylinder 1
OK
E-010
E-035
37 38 39 40 41 42 43 44 45 46
47
48
25 26 27 28 29 30 31 32 33 34
35
36
13 14 15 16 17 18 19 20 21 22
23
24
1
2
3
4
5
6
7
8
9 10
11
12
1
2
-
+
RT21065033
Multimeter
Connection
Condition
Specified
Condition
E-010 (2) - E-035
(4)
Always
Continuity
Multimeter
Connection
Condition
Specified
Condition
E-010 (2) or
E-035 (4) - Body
ground
Always
No continuity
E-010 (2) or E-
035 (4) - Battery
positive
Repair or replace wire harness or
connector (injector of cylinder 1 - ECM)
NG
OK
06–
85
06
a. Check resistance of injector of cylinder 1.
a. Use X-431 3G diagnostic tester to read the ECM DTC.
b. Refer to "DTC Confirmation Procedure".
c. Check if DTC P0201-00 still exists.
6
Check injector of cylinder 1
1
2
RT21080290
-
+
Multimeter Connection
Specified
Condition
1 - 2
12 Ω (at 20°C)
Replace injector of cylinder 1
NG
7
Check for DTCs
OK
Replace ECM
NG
System is operating normally.
Reassemble vehicle and perform a road test to confirm that malfunction reported by customer has
been repaired.
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст