Chery Tiggo 5 (T21). Service manual — part 486
45–
22
45
5. Remove the defroster duct assembly.
a. Remove 4 fixing screws (arrow) from defroster duct
assembly.
(Tightening torque: 1.5 ± 0.5 N·m)
b. Remove the left defroster duct assembly (1) and right
defroster duct assembly (2) from instrument panel
assembly.
6. Remove the center defroster duct assembly.
a. Remove 6 fixing screws (arrow) from center defroster
duct assembly.
(Tightening torque: 1.5 ± 0.5 N·m)
b. Remove the center defroster duct assembly from
instrument panel assembly.
7. Remove the instrument panel left outlet assembly.
a. Using a screwdriver wrapped with protective tape, pry up the claws on instrument panel left outlet
assembly.
b. Remove the instrument panel left outlet assembly
from instrument panel assembly.
8. Remove the instrument panel right outlet assembly.
a. Remove the fixing screw (arrow) from instrument
panel right outlet assembly.
(Tightening torque: 1.5 ± 0.5 N·m)
RT21450400
2
1
RT21450410
RT21450421
RT21450420
45–
23
45
b. Using a screwdriver wrapped with protective tape, pry
up the claws on instrument panel right outlet
assembly.
c. Remove the instrument panel right outlet assembly
from instrument panel assembly.
9. Remove the front passenger airbag.
a. Disengage the claws from front passenger airbag.
b. Remove the front passenger airbag from instrument
panel assembly.
Assembly
Assembly is in the reverse order of disassembly.
Installation
Installation is in the reverse order of removal.
RT21450430
RT21450440
CAUTION
Make sure to tighten fixing bolts and fixing screws to the specified torque when installing instrument
panel assembly.
Check airbag for proper installation after installing instrument panel assembly.
Check each electrical equipment for proper operation after installing instrument panel assembly.
45–
24
45
Instrument Panel Crossmember Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the instrument panel assembly (
4. Loosen the instrument panel fuse and relay box.
a. Remove 2 fixing bolts (arrow) from instrument panel
fuse and relay box, and loosen the instrument panel
fuse and relay box.
(Tightening torque: 7 ± 1 N·m)
5. Loosen the connector mounting bracket.
a. Disconnect the connectors (1) from the inner part of
connector mounting bracket.
b. Remove 2 fixing bolts (arrow) from connector
mounting bracket, and loosen the connector mounting
bracket.
(Tightening torque: 7 ± 1 N·m)
6. Loosen the diagnostic interface.
a. Remove 2 fixing screws (arrow) from diagnostic
interface, and loosen the diagnostic interface.
(Tightening torque: 1.5 N·m)
CAUTION
Be sure to wear safety equipment to prevent accidents when removing instrument panel crossmember
assembly.
DO NOT scratch interior and body paint when removing instrument panel crossmember assembly.
RT21450450
RT21450460
1
RT21450470
45–
25
45
7. Remove the smart entry start controller.
a. Disconnect the connectors (1) from smart entry start
controller.
b. Remove 2 fixing nuts (arrow) from smart entry start
controller, and remove the smart entry start controller.
(Tightening torque: 7 ± 1 N·m)
8. Remove the anti-theft module (for MT model).
a. Disconnect the connector (arrow) from the anti-theft
module.
b. Remove the fixing bolt (1) from the anti-theft module.
(Tightening torque: 7 ± 1 N·m)
9. Remove the instrument panel crossmember lower bracket assembly.
a. Remove 6 fixing bolts (arrow) from instrument panel
crossmember lower bracket assemblies, and remove
the instrument panel crossmember lower bracket
assemblies.
(Tightening torque: 25 ± 3 N·m)
10.Loosen the steering column assembly.
a. Remove 2 fixing nuts (arrow) from steering column
assembly.
(Tightening torque: 25 ± 3 N·m)
b. Remove 2 fixing bolts (1) from steering column
assembly.
(Tightening torque: 25 ± 3 N·m)
c. Separate the steering column assembly from
instrument panel crossmember.
1
RT21450480
RT21450541
1
RT21450481
RT21450490
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст