Chery Tiggo 5 (T21). Service manual — part 215
18–
49
18
DTC Confirmation Procedure:
Confirm that battery voltage is between 11 and 14 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC), and make it
communicate with vehicle electronic module by the data network.
Turn ignition switch to ON.
Using X-431 3G diagnostic tester to record and clear the DTCs stored in the TCU.
Turn ignition switch to LOCK and wait for a few seconds.
Turn ignition switch to ON, and then select "Read Code".
If DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent. Please refer to Intermittent
DTC Troubleshooting.
Diagnosis Procedure
HINT:
After the fault is eliminated, verify DTC and symptom again.
a. Turn ignition switch to LOCK.
b. Disconnect the turbine speed sensor connector.
c. Check if the turbine speed sensor connector is dirty, oxidized, loose or damaged.
DTC Code
DTC Definition
DTC Detection
Condition
Warning Light
Condition
Possible Cause
P0715
Input/Turbine Speed
Sensor Circuit
Start engine and keep
it at following status for
at least 10 seconds:
idle speed or
accelerator not more
than 10%, at P or N
gear, engine speed not
less than idle speed
Turbine speed
signal is higher
than standard
value within a
period
Incorrect
installation of the
turbine speed
sensor
Signal circuit open
or short circuit
Turbine speed
sensor power
circuit poor contact
Turbine speed
sensor failure
TCU signal circuit
failure
P0716
Input/Turbine Speed
Sensor Circuit Range
Difference
between engine
speed and
turbine speed
exceeds
standard value
and keep for
900ms
1
Check wire harness connector
Repair fault
NG
OK
18–
50
18
a. Turn ignition switch to LOCK and disconnect the negative
battery cable.
b. Disconnect the wire harness connectors E-030 and E-049.
c. Check for continuity between the terminals 21, 22 and 55
of wire harness connector E-030 and terminals 3, 2 and 1
of connector E-049.
a. Turn ignition switch to LOCK and disconnect the negative
battery cable.
b. Disconnect the wire harness connector E-030.
c. Check for continuity between the terminals 21, 22 and 55
of wire harness connector E-030 and ground.
2
Check engine compartment wire harness
-
+
RT21180920
E-030
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
E-050
6
4
2
1
5
3
8
7
9
10
Replace engine compartment wire
harness
NG
3
Check if TCU wire harness connector E-030 and ground is conductive
OK
-
+
RT21180930
E-030
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
Repair or replace failed circuit
NG
OK
18–
51
18
a. Turn ignition switch to LOCK and disconnect the negative
battery cable.
b. Disconnect the wire harness connector E-030.
c. Check if the terminals 21, 22 and 55 of wire harness
connector E-030 are short to power.
a. Correctly install a new turbine speed sensor.
b. Check whether the system is normal.
a. Using X-431 3G diagnostic tester, select Read Code.
b. Check if DTC P0715 or P0716 still exists.
4
Check if TCU wire harness connector E-030 is short to power
RT21180940
-
+
V
E-030
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
Repair or replace failed circuit
NG
5
Check turbine speed sensor
OK
Diagnosis complete
NG
6
Check for DTC
OK
Replace TCU
NG
System is normal
OK
18–
52
18
DTC
P0720
Output Speed Sensor Circuit
DTC
P1745
Second Speed Sensor Plausible
ET21180100
TCU
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
SECONDARY SHAFT
SPEED SENSOR
54
50
19
O
Y
LW
1
2
3
E-030
B
E-030
B
E-079
E-079
1
2
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст