Chery QQ3. Service Instruction — part 4
Start and Operation
40
economy and prolong the life of the
tire.
Keep certain distance with other
cars to avoid emergency brake so as
to depress the wear and tear of the
brake patch and improve the fuel
economy(because there is no need
for additional fuel to accelerate).
Do not load unnecessary goods to
add the weight.
Do not leave your feet on the pedal
which will cause unnecessary worn
or even damage the brake and
increase the consume of fuel.
Keep the condition when the car
left the factory.
Notice the exhaust gas of the engine
(carbon monoxide)
Do not inhale the exhaust gas of the
engine which is harmful, or you
will examinate or even die with
excessive gas.
Whenever you suspect that there is
exhaust gas entering the car, go to the
Chery Service Station immediately for a
check. If you have to drive under this
condition, please open all the windows
completely.
To prevent the gas from entering the car,
please check the exhaust system and body
regularly.
Lift the car and check when
replacing the oil.
Notice the change of the sound of
exhaust system.
Do not let the exhaust system,
chassis or the tail be damaged or
corroded.
Notice at the same time:
Do not start the engine in a narrow
place such as garage or other closed
places.
When the engine maintain running
for a long time in an open
circumstance, you should set the
conditioner to outer circulate mode
and let the fresh air into the car, and
set the blower to high speed
position.
Do not stay in a car with engine
running idle for a long time, neither
leave the children in it.
Avoid the tail door open during a
driving because the exhaust gas
might get into the car. If the tail
door has to be opened, please close
all the windows. Set the conditioner
to outer circulate mode and let the
fresh air into the car, and set the
blower to high speed position.
Driving in danger:
When driving on watery, snowy, icy,
muddy, sandy or similar kind of
dangerous roads, you should follow these
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Start and Operation
41
advices:
Start and Operation
Drive carefully for the brake
distance will be prolonged.
Avoid brake or steering.
Step slightly on the brake pedal
until it stops during a brake.
If the car get stuck in snow, mud or
sand, accelerate with 2-speed gear
to avoid sliding of the front wheel.
Spread some rocks and stones
under the front wheel when the car
getting stuck in snow or mud, or
use tire chain or other antiskid to
increase the adh esive power.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
42
Instruments and control devices
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
43
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
44
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
45
1.Steering switch
2.Horn button
3.Cluster gauge
4.Ignition switch
5.Wiper switch
6.Temperature cont rol switch
7.Center ventilation opening
8.Hazard warning switch
9.Anti-theft indicator light
10.Blower motor switch
11.Side ventilation opening
12.Front windshield defroster ventilation opening
13.Glove box
14.Rear window defroster switch
15.Radio/cassette
16.Airflow distribution switch
17.Ashtray
18.Package bo x
19.Cogarette lighter
20.Interior and outer circulation control lever
21.Accelerator pedal
22.A/C switch
23.Brake pedal
24.Clutch pedal
25.Engine hood inner opener handle
26.Headlight regulator switch
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
46
Speedometer
Speedometer ind icates automobi le
running speed (km/h)
Vehicle speed warning
buzzer
While vehicle speed exceeds 120 km/h ,
the vehicle speed warning buzzer will
sound ( within specified market)
Odometer
The upper counter of odometer records
total mileage, while the lower counter
records travel mileage. The last digit of
the lower counter represents a unit of 100
meters (or l/10 kilometer).
Coolant temperature
gauge
When ignition switch is set in" Ⅱ
"position, coolant temperature gauge
indicates engine cool ant temperature.
!Notice
When indicator stays in red area,
engine is likely to be
overheated ,engine should be
stopped as soon as possible to cool
down.
Fuel gauge
Fuel gauge indicates the liquid level of
fuel tank. Fuel gauge indicates no fuel
level after ignition switch is shut. After
ignition switch is turned on, if additional
fuel is added, fuel gauge pointer will
move to new position slowly. During
braking, accelerating and turning, fuel
gauge pointer will wiggle, which results
from the shock of the fuel in fuel tank.
Fuel tank capacity: 35Litre.
H: Cool
C: Hot
F:Full
E:Empty
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
47
Fuel level warning light
Fuel will run out soon when the light
goes on.
The lamp will light up when the
remaining fuel in tank drops to 5.5 liters.
Once the warning light is on, fuel should
be added as soon as possible.
!Notice
The catalytic converter and fuel system
may function improperly if fuel is
exhausted, therefore, fuel should be
added in time if the warning light is on.
Engine malfunction
indicator light
With ignition switch is turned on, engine
malfunction indicator light will light up
for about 4 seconds until it goes out.
If indicator light is on, during normal
operation, it indicates a fault. The electric
cont rol fuel injection system will
switched to emergency mode to keep
driving, driver should contact CHERY
AUTO authorized service station
immediately for trouble shooting.
!Notice
If engine malfunction indicator light stays
on, it indicates a failure. Driver should
contact CHERY AUTO authorized
service station for troubleshooting.
Engine oil pressure
warning light
With ignition switch is turned on, the
light will light up and go out after engine
is started.
If the light goes on during driving, engine
oil level should be checked. The specified
engine oil should be added to normal
level if it is because of the lack of
engine oil. If oil level is ok, cont act
CHERY AUTO authorized service
station.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
48
!Notice
If engine oil pressure warning light stays
on, it indicates a failure. If it happens
during driving, stop the vehicle to check
for the lack of engine oil as soon as
possible. Add engine oil if necessary. If
there is no problem with engine oil, go to
the nearest CHERY AUTO authorized
service station for inspection.
Brake system warning
light
With ignition switch on, the light should
light up after hand brake is applied. The
light should goes out after the hand brake
is released.
The hand brake should be released fully
before moving. If the light still remains
on after the hand brake is released, it
indicates a lack of brake fluid. Take the
following steps:
Park the vehicle at roadside.
Check the brake fluid level; add the
brake fluid specified by CHERY
AUTO CORPORATION to the
MAX mark if necessary.
If brake is ok and brake system is
functional, go to the nearest
CHERY AUTO authorized service
station immediately at safe speed
for further inspection.
If a leakage of brake fluid is found,
the warning light remains on or the
brake functions improperly, tow the
vehicle to CHERY AUTO
authorized service station for
inspection and service.
!Notice
With ignition switch turned on and hand
brake applied, there may be failure in
brake system if the brake system warning
light isn't on. Lamp bulb should be
checked for malfunction. If the bulb is ok,
check the brake system; if brake fluid
warning light remains on, it indicates a
low brake fluid level and brake
performance may be affected. If the
above happens during a driving, the
vehicle should be slowed down and
stopped for the following inspections
1.Check brake fluid reservoir and add
specified brake fluid if the liqu id level is
low.2.Check brake for function.3.If brake
functions normally, drive the vehicle to
service center slowly for inspection.4.If
warning light stays on while brake is
normal or a brake fluid leakage is found,
tow the vehicle to CHERY AUTO
authorized service station. If brake fluid
level is too low, the braking distance,
brake force and pedal range will be
increased.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
49
ABS warning light
With ignition switch is turned on, ABS
indicator light will light up for about 4
seconds before it goes out.
With ignition switch turned on, if the
ABS light is not lit or remains on, contact
the nearest CHERY authorized service
station.
If ABS light is lit up during driving, there
is a fault in ABS system With ABS not
working, if the brake system functions
properly, go to the nearest CHERY
AUTO authorized service station for
inspection.
Generator warning light
It indicates a discharge of vehicle battery.
With ignition switch turned on, the light
will light up and goes out after engine is
started. If the light goes on during driving,
the following steps should be taken:
·Park the vehicle at roadside.
·Check generator belt for slackness or
cracks.
·If generator belt is normal, there may be
failure in charging system. Isolate the
problem and correct it as soon as possible
and to the nearest CHERY AUTO
authorized service station for a system
inspection immediately.
!Notice
If the generator belt is too loose, the
generator sup erheating may be caused
and subsequent damage may happen to
the generator. Therefore, the generator
belt should be inspected regularly.
Safety belt warning light
With ignition switch in "II" position,
safety belt warning light will come on
unless driver fastens safety belt.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
50
Airbag warning light
With ignition switch is turned on, if
airbag warning light comes on and goes
out after about 4 seconds, airbag system
is normal.
If airbag warning light does not
illuminate or remains on after about 4
seconds, or continuously blinks or
remains on with vehicle running, airbag
system malfunction is indicated. Airbag
system will not be triggered when airbag
protection is needed in an accident. Go to
the nearest CHERY AUTO authorized
service station for inspection.
Turn signal indicator
lamp/ hazard warning
flasher indicator
When turn signal light switch or hazard
warning lamp switch is turned on,
indicator light’s blinking indicates the
working condition of outer signal lamp or
hazard warning lamp.
A smaller
frequency of blinking indicates a fault in
turn signal indicator light bulb.
!Notice
If bulb is blown, replace it immediately
for avoiding accident. If green arrow does
not illuminate when turn signal switch is
switched on, check for blown fuse or
bulb.
Headlight high beam
indicator light
When high beam switch is turned on,
indicator light will come on.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
51
Foglight/rear foglight
switch
First position with front foglights on.
Second position with front and rear
foglights on or only with rear foglights
on.
With switch in second position, the
operation indicator light on switch will
illuminate.
With ignition switch on,front foglights
will op erate only when parking lights are
turned on. They may work with high
beams or low beams simultaneously. Rear
foglight can only be operative with front
foglights simultaneously.
Rear foglights are allowed to apply only
when there is a very low visibility (with a
visibility distance less than 50 meters) for
their stronger dazzle.
!Notice
Do not light up after engine is stopped, or
battery will be discharged. Headlamp
lower beam asymmetry is designed to
increase sight scope. In left driving
countries, there must be a black cover on
the headlight glass zone with 1 5 angle.
Transmission warning light
(for the vehicle with AMT
transmission)
The light ON after the ignition switch
turns on, and then off after about 4 s.
If the light fails to light after the ignition
switch turns on, or if the light doesn’t
extinguish after it lights, please cont act
the nearest special CHERY service
station. If the light ON during the vehicle
is traveling, it shows that the ABS has
fault. If there is no ABS function while
the vehicle’s brake system still works as
before, please get to the nearest special
CHERY service station ASAP to have it
examined.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
52
Transmission oil
temperature warning light
(for the vehicle with AMT
transmission)
The light ON after the ignition switch
turns on, and then extinguishes after
about 4 s.
If the light fails to light after the ignition
switch turns on, or if the light doesn’t
extinguish after it lights, please cont act
the nearest special CHERY service
station. If the light ON during the vehicle
is traveling, it shows that the ABS has
fault. If there is no ABS function while
the vehicle’s brake system still works as
before please get to the nearest special
CHERY service station A.S.A.P. to have
it examined.
Position display (for the vehicle
with AMT transmission)
After the ignition switch turns
on, the position of gear selector
lever will be displayed on the
center display of instrument
panel.
All position displays are shown in the
following figures:
R position:
N position:
Instruction mode:
In the case of instruction mode,
the gear position selected by a
driver will be displayed in the
display with the form of digital.
In the following figure, the 2
nd
gear is taken as an example.
AUTO mode:
In the case of AUTO mode, the
current gear position will be
displayed in the display with
the form of digital. In the
following figur e, the 2
nd
gear is
taken as an example.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
53
Digital instrument (
)
This instrument has two keystrokes: “ SEL”
and “T RIP”; the “TRIP” is a trip computer and
traveling time switchover/reset button, and the
“ SEL” is a function select button. The profile
of this instrument is shown below:
Speedometer
The speedometer displays the running speed of
a vehicle (unit: km/h), with the range of 0–199
km/h, which is displayed in the form of
digitals, and the division of display: 1 km/h.
Odometer
With the digital display, the odometer has a
overall mileage count er (ODO) which can record
the max. mileage of 999,999 km; and two trip
meters (TRIP A/TRIP B) which can record the
max. mileage of 9,999.9 km.
Water temperature indicator
When the ignition switch is placed on the
position “Ⅱ”
, the water temperature
indicator will indi cate the temperature
of the engine coolant. The
column-shaped display includes 10
scales and 10 divisions.
Speedometer Display
Two trip meters (TRIP
A/TRIP B) and
travelling time display
Overall
mileage
display
H: Hot
C: Cold
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
54
! CAUTION:
When the pointer gets to the red area, the
engine may he overheat, and you shall
immediately stop your vehicle to cool the
engine. In this case, if you drive your
vehicle continuously, it may damage the
engine.
Fuel gauge
The fuel gauge indicates the level of fuel
remained in the fuel tank. The gauge
will not display the fuel level after the
ignition switch closed. If refuelling into
the tank, the reading of fuel gauge will
slowly change to the new level of fuel.
In case of braking, accelerating or
turning, the pointer of fuel gauge will
waggle. This is caused by the vibration
of fuel in the tank.
● Capacity of fuel tank: 35L.
Fuel alarm indicator lamp
In case that this indicator lamp lights, it
indicates that the fuel will be used up
soon. When the fuel remained in the tank
reduces down to 5.5 L, this indicator
lamp lights. Refuel as soon as possible
once the alarm indi cator lamp lights.
Engine trouble indicator lamp
The engine trouble indicator lamp lights
when the ignition switch is turned on, and
extinguishes after the engine starts up.
If the indicator lamp lights when the
engine operates normally, it shows that
there is a certain trouble. In this case,
switch the electronic injection system to
the emergency running program, and then
drive the vehicle continuously, however,
immediately cont act the
Chery
Authorized Service Station to remove the
trouble.
If the engine trouble indicator lamp lights
in a short time and then extinguishes, it is
a normal phenomenon and doesn’t show
that the system has any trouble..
!CAUTION
In case that the engine trouble indicator
lamp lights for a lon g time, it indicates
that the engine has some one trouble, and
you shall contact the Chery Authorized
Service Station and remove the trouble in
time.
F: Full
E: Empty
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and control devices
55
Engine oil pressure alarm
indicator lamp
The indicator lamp lights when the
ignition switch is turned on, and
extinguishes after the engine starts up.
If the indicator lamp lights when the
vehicle is traveling, check the level of
engine oil. If the engine is short of oil,
refill the specified engine oil to the
normal level of oil; and if the oil level is
normal, please take care to cont act the
Chery Authorized Service Station.
!CAUTION
In case that the engine oil pressure alarm
indicator lamp lights for a long time, it
indicates that the engine has some one
trouble, please immediately stop your
vehicle to check whether there is short of
engine oil when the vehicle is traveling,
and, if necessary, refill the oil; if the
engine oil is normal, please get to the
nearest Chery Authorized Service Station
to have your vehicle checked.
If the engine oil pressure alarm indicator
lamp lights when the vehicle is traveling,
stop your vehicle to have it checked. In
this case, the continuous travel may
damage the engine, without the warranty.
Brake system alarm indicator
lamp
Pull up the hand brake after the ignition
switch is turned on, and then the indicator
lamp lights, and extinguishes after the
hand brake is released.
Before driving, completely release the
hand brake. If the indicator lamp still
lights after the completely releasing of
hand brake, it shows that there is short of
brake fluid. In this case, you shall:
● park your vehicle on the roadside;
● check the level of brake fluid, and, if
necessary, refill the brake fluid
specified by the CHERY company to
the M AX mark;
● immediately drive your vehicle at the
safety speed to the nearest Chery
Authorized Service Station to have it
checked if the brakes are normal and
the brake system is confirmed very
safe;
● drag your vehicle to the nearest
Chery Authorized Service Station to
have it checked and repaired if you
find any one of the following
troubles: brake fluid leakage, the
alarm indicator lamp lights for a
long time, or the brake fails to work
normally.
!CAUTION
The brake system alarm indicator lamp
doesn’t light after the ignition switch is
turned on and the hand brake is pulled up,
it shows that the brake system may be in
trouble. Check whether the bulb has some
troubles. If the bulb is working normal,
check the brake system; if the brake fluid
alarm indicator lamp lights for a long
time, it indicates that the level of brake
fluid is low, which may make influence
on the braking performance. In this case,
if you are driving your vehicle, you shall
gradu ally decelerate till stop your vehicle,
and carry out the following checks:
1. check the brake fluid reservoir, and if
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст