Peugeot Partner Tepee (2017 year). Instruction — part 7

95

EASE OF USE and COMFORT

4

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Overhead storage unit

This is located above the sun visors
and can accommodate various objects

(a jumper, file, gloves...).
The openings concealed by the sun
visors allow you to see and access the
objects stored in the overhead storage
unit.
The maximum weight permitted in the
overhead storage unit is 5 Kg.
Do not place objects in this storage
unit which could present a risk to the
occupants.

Central storage console

This console offers an appreciable
additional storage area: it can be
removed and clips onto a base which
also incorporates two cup holders at
the rear.
Ensure that the object (bottle, can...)
placed in the cup holder is retained
securely and does not risk being
dislodged while driving.
Any liquid which could spill presents
a risk of damage on contact with the
instrument panel and centre console
controls.
Take care.

Sun visor

To prevent dazzle from ahead, fold the
sun visor down.
A pocket is provided in the driver's sun
visor for storing toll cards, tickets, ...

Storage compartment under

seats

Storage compartments are available,

with or without lid, in the floor under the

front seats.
To gain access to them, move the seat
forward. The lid must be lifted from the
rear of the seat.

96

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

SEATING AREA FITTINGS

Floor boxes

Two boxes are available, located under
the rear passenger footwells.
To open them, slide your fingers into

the recess and lift the lid.

Aircraft style tables

To put the table in place, pull it
upwards and fold it down.
As a safety precaution, above a high
pressure, the table is designed to
unhook.
To put it back in place, with the table
vertical, engage one side then the
other, forcing slightly.
Do not place hard or heavy objects
on the table. They could become
dangerous projectiles in the event of
sharp braking or impact.
A bag hook is provided on the side of
each table.

Side blinds

Side blinds may be available on the
sliding side doors.
Pull the side blind by the tab to install
it.
To avoid damaging the blind when
opening the door, check that the tab is
hooked securely.

Always guide the blind slowly
using the tab, both when raising
and when lowering.

97

EASE OF USE and COMFORT

4

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

ZENITH ROOF

The multifunction roof extends the
overhead storage unit. It consists of
the following components:

Storage compartments

Storage compartments are provided
on each side of the roof. The maximum
authorised load is 6 kg.
The translucent base assists with

finding objects stored inside.
Do not store objects which could
present a risk to the occupants.

Courtesy lamp

The operation of the courtesy lamp is
identical to that of the front courtesy lamp.

Refer to chapter 4 "Practical
information", "Courtesy lamps"
section.

98

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

From inside

From outside

Rear box

This roof box can be accessed from
the rear seats and the boot.
From the rear seats, slide the flaps

to open.

Vents

A 3-position control allows you to

adjust the air flow through the vents.

The vents are also fitted with a scented

air freshener.

From the boot, place your thumb on the
recess then pull the handle to open.

Open carefully to prevent objects
stored in this interior roof box from
falling out.

The maximum authorised load is 10 kg.

99

EASE OF USE and COMFORT

4

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

SCENTED AIR FRESHENER

The scented air freshener diffuses
a fragrance in the passenger
compartment from the roof console
vents.

Adjusting the flow

Turn the chromed button to adjust the
diffusion:
-

to the left to decrease,

-

to the right to increase.

To stop the diffusion, turn the chromed
button fully to the left.

Removing the scented air

freshener

-

Press the button down while turning
it a quarter of a turn to the left to
the stop.

-

Remove the scented air freshener
from the roof console.

-

Replace the cartridge.

100

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Replacing a cartridge

The scented air freshener refill consists

of a cartridge

B and its sealing case C.

- Remove the protective film

D.

-

Place the head of the cartridge

B

on the button

A of the scented air

freshener.

-

Turn it a quarter of a turn to lock it
on the button and remove the case.

-

Insert the scented air freshener in
its location.

You can change the cartridges at any
time and store cartridges which have
already been started in their original
case.
The scented air freshener button

A is

independent of the cartridge.
The cartridges are supplied without the
button

A.

Inserting the scented air freshener

After fitting or changing the cartridge:
-

Put the scented air freshener back
in place in its location.

-

Turn it a quarter of a turn to the
right.

Good practice

As a safety precaution, only use the
cartridges provided for this purpose.
Do not dismantle the cartridges.
Keep the cartridge sealing cases
which are used as packaging when the
cartridges are not in use.
Never try to refill the cartridges with

fragrances other than those available
from PEUGEOT dealers.
Keep out of reach of children and
animals. Avoid contact with the skin
and eyes. If swallowed, consult a
doctor and show him the packaging or
product label.

The scented air freshener button

A can

only be fixed on the multifunction roof

console with a cartridge.
Therefore, always retain button

A and

a cartridge.
The cartridges are available from
PEUGEOT dealers.

101

EASE OF USE and COMFORT

4

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

ZENITH ROOF BARS

The maximum authorised weight on
each roof bar is 35 kg.

In all cases, the load must rest on
the non-slip bands provided for this
purpose and must not touch the roof or
the glazing of the roof.

Recommendations for loading the

roof
This procedure requires the use of
a spanner supplied with the tools for
changing a wheel.

These two longitudinal Zenith roof bars
can be removed.

Chapter 9, "Changing a wheel"
section.

-

Open the protective covers.

-

Slacken the four screws using the
spanner and remove them.

-

Turn the bars 90° placing the
hollow parts towards the front.

- Refit the the 4 screws and tighten

them using the spanner.

-

Close the protective covers.

-

Use the strap passages

A only to

secure the load firmly.

102

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

ExTERIOR ROOF BARS

If you install transverse bars on these bars, refer to the weight values indicated
by the manufacturer but do not exceed: 75 kg.

103

EASE OF USE and COMFORT

4

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Automatic switching on/off
The front courtesy lamp comes on
when the key is removed from the
ignition, when the vehicle is unlocked,
when one of the front doors is opened
and for location of the vehicle using the
remote control.
It goes off gradually after the ignition
is switched on and when the vehicle is
locked.

Front seats: comes on when
one of the front doors is
opened.

These are switched on and off by
means of a manual switch, with
the ignition on.

Rear seats: comes on when
one of the rear doors is
opened.
If the doors remain open for
a few minutes, the courtesy
lamps go off.

Permanently off.

Permanently on, ignition on.

Front courtesy lamp

COURTESY LAMPS

Rear courtesy lamp

Front individual reading lamps

104

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

LOAD SPACE COVER (5 SEAT VERSION)

This rigid shelf conceals the objects
stored in the boot.

Removing
Fold the load space cover.
Detach it from the notches

A and B

pulling it towards you.
Raise it and remove the assembly.

Refitting
Place the load space cover in front
of

A and B.

Push it forwards to insert the lugs in
the notches.
Unfold and clip into the notches

C.

Folding
From the boot, fold the half-shelf,
raising it to detach it from the notch

C.

Storing (according to version)
A location is provided in the back of the
rear seats to accommodate the load
space cover folded onto itself.
Slide it vertically between the side
guides located at mid seat back height.
Insert the hinge first, with the free flaps

turned upwards.

This rigid load space cover can
form a shelf. However, as a safety
measure, do not place objects

on it which could become dangerous
projectiles in the event of sharp braking
or rear impact.

105

EASE OF USE and COMFORT

4

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

12 volt socket (120 W max)

It is advisable to limit the use of this
socket to avoid discharging the battery.

Protective net

Open the cover located in the hook
support.
Fix the top of the net in the notches,

having first turned the bar 1/4 of a turn.
Ensure that the end of the bar engages
correctly in the metal part of its
location.
Fix the straps in the locations provided

on the floor.
Tighten the net using the straps.

Stowing rings

Use these rings to secure loads on the

floor.

The connection of an electrical
device not approved by
PEUGEOT, such as a USB

charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor telephone
reception or interference with displays
in the screens.

106

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

REAR FITTINGS

(7 SEAT VERSION)

Cup holder

Any liquid carried in a cup (mug or
other) on board which could spill,
presents a risk.
Take care.

12 volt socket (120 W max)

It is advisable to limit the use of this
socket to avoid discharging the battery.

Stowing rings

Use the stowing rings on the floor to

secure and retain your loads firmly.
The seat belt anchorages must not be
used for this purpose.

It is recommended that the load
is immobilised by securing it

firmly using the stowing rings on

the floor.

107

EASE OF USE and COMFORT

4

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Storage flaps

Raise the corresponding flap.

Next to the boot sill, the recess is
intended to receive the roller tube
containing the load space cover.

Seat belts

Ensure that the centre seat belt has
reeled in correctly to its carrier in the
roof.
Prevent the row 3 seat belt buckles
from knocking by raising them as close
as possible to the anchorages in the
roof.
The seat belt buckle attachment rings
on each side of the boot must not be
used to retain loads.

108

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

BLIND, LOAD SPACE COVER

Position the load space screen so as to

present the rear load space cover flaps

towards you.
Engage the left-hand lug of the roller in
the support

A.

The load space cover is the roller blind
type. Take care not to place heavy
objects on the load space cover when
unreeled.

Compress then place the right-hand
lug facing the support

B.

Release to engage the roller in its
support.
Unroll the load space cover to the rear
side pillars.
Engage the ends in the rear notches to
keep it taut.

To install it
Place the row 3 seats in the fully folded
position.
Raise the storage flap at the boot sill.
Take hold of the roller in the centre and
compress it towards the left-hand pillar.
Raise the assembly.

109

EASE OF USE and COMFORT

4

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Practical information

Partner2VP_en_Chap04_Ergonomie_ed02-2016

To remove it
From the boot, pull the load space
cover towards you to release it from the
side pillars.
Guide the load space cover as it rolls
up.
Remove the clips of the three flaps from

the base of each row 2 head restraint.
Compress the roller to the left to remove
it from the support

B.

Raise it and pivot it forwards.

To store it
Store it in the recess at the boot sill,

with the two rear flaps uppermost.
First, compress the load space screen
to the left.
Release.
Arrange the two flaps and close the

storage flap.

The roller is fitted with three flaps

permitting concealment of the
boot, whether the row 2 seats
are in the normal position or the
comfort position.

Each flap has two clips which are

hooked on the base of each head
restraint.

11

0

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Mirrors and windows

Partner2VP_en_Chap04_Ergonomie_ed02-2016

Adjusting electric door mirrors

-

Move the control to the right or to
the left to select the corresponding
mirror.

-

Move the control in all four
directions to adjust.

-

Return the control to the central
position.

MIRRORS

Heated mirrors

Adjusting manual door mirrors

Forced folding

If the mirror casing has come out of
its initial location, with the vehicle
stationary reposition the mirror casing
manually or use the electric folding
control.

Press the heated rear screen
button.

Move the lever in all four directions to
adjust.
When the vehicle is parked, the door
mirrors can be folded back manually.
The mirrors are not equipped with
automatic heating.

Electric folding / unfolding

The mirrors can be folded or unfolded
electrically from the inside, with the
vehicle parked and the ignition on:
-

Place the control in the central
position.

-

Turn the control downwards.

The mirrors that have electric folding/
unfolding can be heated.