Peugeot 3008 (2023 year). Manual in english — page 8
Driving
Driving situations and related alerts
To receive all the necessary information on the instrument panel, first select the "Driving" display mode.
The table below describes the alerts and messages displayed in different driving situations.
The actual order of display of these alerts may be different.
Function status
Indicator lamp
Display and/or associated
Comments
message
ON
System active, conditions not met:
- Speed below 43 mph (70 km/h).
- No lane marking recognised.
(grey)
- ASR/DSC systems deactivated or operation of ESC
system triggered.
- "Sporty" driving.
ON
Automatic standby of the function (e.g. detection of a
trailer, use of the "space-saver" type spare wheel supplied
with the vehicle).
(grey)
ON
Lane marking detected.
Speed above 43 mph (70 km/h).
(green)
ON
The system corrects the trajectory on the side where the
risk of unintentional crossing is detected (orange line).
(orange)/(green)
148
Driving
Function status
Indicator lamp
Display and/or associated
Comments
6
message
ON
- If, during the correction, the system detects that the
driver has not held the steering wheel for a few seconds, it
stops the correction and returns control to the driver.
(orange)/(green)
- During the trajectory correction, the system determines
"Put your hands back on
that the correction will not be enough: the driver is warned
the steering wheel"
that they must provide additional trajectory correction.
The duration of audible warnings will increase if multiple
corrections are performed in quick succession. The
warning will become continuous, persisting until the driver
responds.
This message may also be displayed with your hands on
the steering wheel.
- Inactivity by the driver detected during
Risk of undesirable operation
Operating limits
correction.
The system should be deactivated in the
The system goes into standby automatically in
the following cases:
The following situations may interfere
following situations:
- ESC deactivated or operation triggered.
with the operation of the system or
- When changing a wheel or working near a
- Speed below 43 mph (70 km/h) or greater
prevent it from working:
wheel.
than 112 mph (180 km/h).
- Insufficient contrast between the road
- Towing or with a bicycle carrier on a towing
- Electrical connection to a trailer.
surface and the verge or hard shoulder
device, especially with trailer not plugged in or
- Use of a "space-saver" spare wheel detected
(e.g. shade).
not approved.
(as detection is not immediate, deactivation of
- Lane markings worn, hidden (e.g. snow,
- Road in poor condition, unstable or with very
the system is recommended).
mud) or multiple (e.g. roadworks).
poor grip (risk of aquaplaning, snow, ice).
- Dynamic driving style detected, pressure on
- Close proximity to the vehicle in front (lane
- Adverse weather conditions.
the brake or accelerator pedal.
markings may not be detected).
- Driving on racing circuits.
- Driving over lane markings.
– Roads that are narrow, winding.
- Driving on a rolling road.
- Activation of the direction indicators.
- Crossing the inside line on a bend.
– Driving on a tight bend.
149
Driving
Activation/Deactivation
Active Safety Brake with
This system includes three functions:
- Collision Risk Alert.
Collision Risk Alert and
- Intelligent emergency braking assistance
(iEBA).
Intelligent emergency
- Active Safety Brake (automatic emergency
braking assistance
braking).
For more information, refer to the
General recommendations on the use
of driving and manoeuvring aids.
► Press and hold this button to deactivate or
press briefly to reactivate the system at any time.
Deactivation is signalled by the lighting of the
indicator lamp in the button.
The state of the system is stored when the
This system:
ignition is switched off.
- warns the driver that their vehicle is at risk of
collision with the preceding vehicle, a pedestrian
Malfunction
or a cyclist.
The vehicle has a camera located at the top of
In the event of a malfunction,
- reduces the vehicle's speed to avoid a
the windscreen and, depending on version, a
these warning lamps light up on
collision or to limit its severity.
radar located in the front bumper.
the instrument panel, accompanied by the
The speed will be reduced by a
This system does not replace the need
display of a message and an audible signal.
maximum of 16 mph (25 km/h) (versions
for driver vigilance.
Have it checked by a PEUGEOT dealer or a
with camera only) or by a maximum of 31
This system is designed to assist the driver
qualified workshop.
mph (50 km/h) (versions with camera and
and improve road safety.
radar).
It is the driver's responsibility to continuously
monitor traffic conditions in accordance with
The system also takes motorcyclists into
applicable driving regulations.
account.
It may also react on animals. Animals
As soon as the system detects a
(especially animals smaller than 0.5 m)
potential collision, it prepares the braking
and objects on the road are not necessarily
circuit. This may cause a slight noise and a
detected.
slight sensation of deceleration.
150
Driving
Deactivation/Activation
- Using an automatic car wash.
Following an impact (e.g. a collision), the
6
- Performing any maintenance (e.g. changing a
system is automatically deactivated.
By default, the system is automatically activated
wheel, working inside the engine compartment).
Have it checked by a PEUGEOT dealer or a
at every engine start.
- Placing the vehicle on a rolling bench in a
qualified workshop.
The settings are changed via the
workshop.
Driving/Vehicle touch screen menu.
- Towing the vehicle.
Deactivation of the system is signalled by
Collision Risk Alert
- Following a front bumper deformation (version
the illumination of this warning lamp,
with radar).
This function warns the driver if there is a risk
accompanied by the display of a message.
- Following an impact to the windscreen close to
of collision with the preceding vehicle, or with a
the detection camera.
pedestrian or cyclist.
Operating conditions and
limits
The system is automatically deactivated
Modifying the alert trigger threshold
once the use of a different diameter
Vehicle moving forward without trailer.
This trigger threshold determines the sensitivity
"space-saver" type spare wheel is detected,
Brake system operational.
with which the function warns of the risk of
or if a fault with the two lateral brake lamps is
DSC/ASR systems activated.
collision.
detected.
Seat belts fastened for all passengers.
The threshold is set via the
Stabilised speed on roads with no or low
Driving/Vehicle touch screen menu.
curvature.
The system diagnoses permanently its
► Select one of the three pre-defined
This warning lamp lights up on the
capability and may inhibit itself without
thresholds: "Far", "Normal" or "Close".
instrument panel without any additional
specific driver indication, if the system is
The last threshold selected is memorised when
message, to indicate that the automatic braking
outside of the regular operating conditions
the ignition is switched off.
system is not available.
(e.g. sensor initialization, board voltage out of
regular range, activation of stability system).
Operation
This is a normal behavior indicating that a
condition is not fulfilled and which does not
Therefore, the system may not be available
Depending on the collision risk detected by the
request the support of a workshop.
just after starting the vehicle.
system and the alert trigger threshold chosen
In any situations with ignition on where automatic
by the driver, different levels of alert may be
braking presents a risk, deactivating the
It can be dangerous to drive if the brake
triggered and displayed on the instrument panel.
system via the vehicle's configuration menu is
lamps are not in perfect working order.
The system takes into account the vehicle
recommended, for instance:
dynamics, the difference speed of the own
- Towing a trailer (particularly a trailer without its
vehicle and the object identified for the
The driver must not overload the vehicle
own braking system).
collision risk, and the operation of the vehicle
(keep within the GVW limit and load
- Carrying long objects on roof bars.
(e.g. actions on the pedals, steering wheel) to
height limits for roof bars).
- Driving with snow chains.
trigger the alert at the most relevant moment.
151
Driving
(orange)
Active Safety Brake
Operation
Level 1: visual alert only, warning that the
The system operates subject to the following
preceding vehicle is very close.
conditions:
The message "Vehicle close" is displayed.
- At reduced speed in an urban environment,
(red)
when a stationary vehicle, pedestrian or cyclist
Level 2: visual and audible alert, warning
is detected.
that a collision is imminent.
- The vehicle's speed is between 6 mph and
The message "Brake!" is displayed.
53 mph (10 km/h and 85 km/h) (versions with
camera only) or 87 mph (140 km/h) (versions
While approaching a vehicle too quickly,
with camera and radar) when a moving vehicle
the level 2 alert may be displayed
is detected.
directly.
This warning lamp flashes (for
Important: the level 1 alert depends on the
approximately 10 seconds) as soon as
trigger threshold selected. It reacts only on
the function applies the vehicle’s brakes.
moving vehicles. It is disabled automatically
During the flashing time, the function is not
at lower speed.
available.
With an automatic gearbox, in the event of
It is possible that collision warnings are
automatic emergency braking, keep the brake
not given, are given too late or seem
This function, also called "automatic emergency
pedal depressed, also after a complete stop is
unjustified.
braking", intervenes after the acoustic alert if the
reached, to prevent the vehicle from rolling away.
The driver must always stay in control of the
driver does not operate the brake pedal quickly
With a manual gearbox, in the event of automatic
vehicle and be prepared to react at any time
enough.
emergency braking bringing the vehicle to a
to avoid an accident.
The system aims at reducing the speed of
complete stop, the engine may stall.
impact or avoiding a collision if the driver fails to
react.
The driver can override the automatic
Intelligent emergency
emergency braking at any time by firmly
The speed will be reduced by a
braking assistance (iEBA)
turning the steering wheel and/or firmly
maximum of 16 mph (25 km/h) (versions
This function increases vehicle deceleration
with camera only) or by a maximum of 31
depressing the accelerator pedal.
if the driver does not brake enough to avoid a
mph (50 km/h) (versions with camera and
collision.
radar).
This assistance is only provided if the driver
presses the brake pedal.
152
Driving
The brake pedal may feel hard and
(depending on version). The automatic braking
break after two hours of driving at a speed above
6
vibrate slightly while the function is
system is deactivated until the seat belts are
43 mph (70 km/h).
operating.
fastened.
This alert is issued via the display of a message
If the vehicle comes to a complete stop,
encouraging the driver to take a break,
automatic braking is maintained for 1 to 2
accompanied by an audible signal.
Distraction detection
seconds.
If the driver does not follow this advice, the alert
is repeated hourly until the vehicle is stopped.
For more information, refer to the
The system resets itself if one of the following
Malfunction
General recommendations on the use
conditions is met:
of driving and manoeuvring aids.
This warning lamp lights up on the
- With the engine running, the vehicle has been
instrument panel with the message
Depending on version, the function consists of
stationary for more than 15 minutes.
"Sensor blind" in certain cases.
either the "Driver Attention Warning" system
- The ignition has been switched off for a few
Version with camera only: the system is
alone or combined with the "Driver Attention
minutes.
deactivated.
Warning by Camera" system.
- The driver's seat belt is unfastened and their
Version with camera and radar: the system
door is opened.
may continue to operate in a degraded mode.
These systems are in no way designed
to keep the driver awake or to prevent
As soon as the speed of the vehicle
This may be caused by a reduced visibility
the driver from falling asleep at the wheel.
drops below 43 mph (70 km/h), the
(e.g. rain, fog, snow, blinding by low sun) or by
It is the driver’s responsibility to stop if feeling
system goes into standby.
a real sensor blockage. In this case, stop the
tired.
Driving time starts being counted again once
vehicle and verify if the front camera or the front
Take a break if you are feeling tired or at least
the speed reaches above 43 mph (70 km/h).
radar is covered by dirt, snow, ice or anything
preventing the sensing.
every 2 hours.
In the event of a malfunction, this warning
Driver Attention Warning by
lamp lights up on the instrument panel,
Activation/Deactivation
Camera
accompanied by the display of a message and
This function is set via the touch screen
an audible signal.
Depending on version, the Driver Attention
Driving/Vehicle menu.
Have it checked by a PEUGEOT dealer or a
Warning system may be combined with the
The state of the system is memorised when the
qualified workshop.
Driver Attention Warning by Camera system.
ignition is switched off.
These warning lamps light up on
the instrument panel and/or in the
Driver Attention Warning
warning lamp display for seat belts and front
The system triggers an alert when it
passenger airbag to indicate that the driver's
detects that the driver has not taken a
and/or front passenger's seat belt is not fastened
153
Driving
The following situations may interfere
with the operation of the system or
prevent it from working:
- lane markings absent, worn, hidden (snow,
mud) or multiple (roadworks);
- close to the vehicle ahead (lane markings
not detected);
A warning lamp appears in the door mirror on the
- roads that are narrow, winding, etc.
side in question:
- fixed, immediately, when being overtaken.
- flashing, after a delay of about one second,
Blind spot monitoring
The system assesses the driver's level of
when overtaking a vehicle slowly, and when the
alertness, fatigue and distraction by
direction indicator is used.
For more information, refer to the
identifying trajectory changes in relation to the
General recommendations on the use
lane markings.
Activation/Deactivation
of driving and manoeuvring aids.
To do this, the system uses a camera, placed on
It is set via the Driving/Vehicle touch
the upper part of the windscreen.
screen menu.
This system is particularly suited to fast roads
When the function is activated, this
(speed higher than 43 mph (70 km/h)).
indicator lamp comes on in the instrument
At a first alert level, the driver is warned by the
panel.
message "Be vigilant!", accompanied by an
When starting the vehicle, the warning lamp
audible signal.
comes on in each mirror to indicate that the
After three first-level alerts, the system triggers
system is activated.
a further alert with the message "Dangerous
The status of the system is memorised when the
driving: take a break", accompanied by a more
ignition is switched off.
pronounced audible signal.
This system warns the driver of a potential
The system is automatically deactivated
In certain driving conditions (poor road
danger posed by the presence of another vehicle
when towing with a towing device
surface or strong winds), the system may
(car, lorry, motorcycle) in the vehicle's blind
approved by PEUGEOT.
give alerts independent of the driver's level of
spots (areas hidden from the driver's field of
vigilance.
vision) using sensors located on the sides of the
bumpers.
Operating conditions
- All vehicles are moving in the same direction
and in adjacent lanes.
154
Driving
- The speed of your vehicle must be between 7
by the Service warning lamp coming on and the
6
and 87 mph (12 and 140 km/h).
display of a message.
- When overtaking a vehicle, the speed
Have it checked by a PEUGEOT dealer or a
difference is less than 6 mph (10 km/h).
qualified workshop.
- When overtaken by a vehicle, the speed
The system may be temporarily disturbed
difference is less than 16 mph (25 km/h).
by certain climatic conditions (e.g. rain,
- Traffic is flowing normally.
hail).
- Overtaking a vehicle over a certain period of
In particular, driving on a wet road or going
time and the vehicle being overtaken remains in
from a dry to a wet area can cause false
the blind spot.
alerts (e.g. presence of a cloud of water
- You are driving on a straight or slightly curved
droplets in the blind spot interpreted as a
road.
vehicle).
- Your vehicle is not pulling a trailer, a caravan,
In bad or wintry weather, ensure that the
etc.
sensors are not covered by mud, ice or snow.
No alert is triggered in the following conditions:
Take care not to cover the warning zone in
Operating limits
- presence of stationary objects (e.g. parked
the door mirrors, or the detection zones on
vehicles, safety rails, lampposts, signs).
the front and rear bumpers with adhesive
- vehicles travelling in the opposite direction.
labels or other objects; they may hamper
- on winding roads or in case of sharp turns.
correct operation of the system.
- when overtaking or being overtaken by a
very long vehicle (e.g. truck, bus), which is both
detected in a blind spot from behind and present
Parking sensors
in the driver's field of vision from the front.
- quick overtaking manoeuvre.
For more information, refer to the
- very heavy traffic: vehicles detected in front
General recommendations on the use
and behind are confused with a lorry or a
of driving and manoeuvring aids.
stationary object.
- activation of the Park Assist function.
Malfunction
In the event of a malfunction, this
warning lamp flashes for a few
moments in the instrument panel, accompanied
155
Driving
centimetres, the audible signal becomes
obstacle is detected in front and the speed of the
continuous.
vehicle is below 6 mph (10 km/h).
The sound emitted by the speaker (right or
Front parking sensor operation is suspended if
left) indicates the side on which the obstacle is
the vehicle stops for more than three seconds in
located.
forward gear, if an obstacle is no longer detected
or the vehicle speed exceeds 6 mph (10 km/h).
Adjusting the audible signal
Depending on version, with
The sound emitted by the speaker (front
This system detects and signals the proximity of
PEUGEOT Connect Radio or
or rear) locates the obstacle relative to
obstacles (e.g. pedestrian, vehicle, tree, barrier)
PEUGEOT Connect Nav, pressing this button
the vehicle, whether in front of or behind it on
using sensors located in the bumper.
opens the window for adjusting the volume of
its path.
the audible signal.
Rear parking sensors
► Engage reverse gear to start the system
Deactivation/Activation
(confirmed by an audible signal).
Visual assistance
The settings are changed via
The system is switched off when reverse gear is
the Driving/Vehicle touch screen menu.
disengaged.
The system status is memorised when the
ignition is switched off.
Audible assistance
The rear parking sensors system will be
deactivated automatically if a trailer or
bicycle carrier is connected to a towing device
installed in accordance with the
This supplements the audible signal by
manufacturer's recommendations.
displaying bars on the screen that represent the
The system signals the presence of obstacles
distance between the obstacle and the vehicle
The parking sensors are deactivated while the
within the sensors’ detection zone.
(white: more distant, orange: close, red: very
Park Assist function is measuring a space.
The proximity information is given by an
close).
For more information on the Park
intermittent audible signal, the frequency of
When the obstacle is very close, the "Danger"
Assist function, refer to the corresponding
which increases as the vehicle approaches the
symbol is displayed on the screen.
section.
obstacle.
Operating limits
When the distance between the vehicle and
Front parking sensors
the obstacle becomes less than about thirty
If the boot is heavily loaded, the vehicle may tilt,
Supplementing the rear parking sensors, the
affecting distance measurements.
front parking sensors are triggered when an
156
Driving
Malfunction
• "Zoom view".
6
• "AUTO view".
In the event of a malfunction when
The display is immediately updated with the type
changing into reverse gear, this warning
of view selected.
lamp lights up on the instrument panel,
The system status is not saved when the ignition
accompanied by the display of a message and
is switched off.
an audible signal (short beep).
Have it checked by a PEUGEOT dealer or a
Operating principle
qualified workshop.
Visiopark 1 - Visiopark 2
For more information, refer to the
General recommendations on the use
of driving and manoeuvring aids.
The screen is divided into two parts with a
contextual view and a view from above the
vehicle in its close surroundings.
The parking sensors supplement the information
Using one or two cameras, the close
on the view from above the vehicle.
surroundings of the vehicle are recorded whilst
Various contextual views may be displayed:
manoeuvring at low speed.
- Standard view.
An image from above your vehicle in its close
- 180° view.
surroundings is reconstructed (represented
- Zoom view.
between the brackets) in real time and as the
AUTO mode is activated by default.
manoeuvre progresses.
In this mode, the system chooses the best
It facilitates the alignment of your vehicle when
view to display (standard or zoom).
parking and allows obstacles close to the vehicle
You can change the type of view at any time
to be seen. It is automatically deleted if the
With the engine running, these systems allow
during a manoeuvre.
vehicle remains stationary for too long.
views of your vehicle’s close surroundings to be
► Press the button in the bottom left-hand
With Visiopark 2, the image is created using
displayed on the touch screen using one camera
corner of the touch screen.
both cameras, when going forward and when
for Visiopark 1 and two cameras for Visiopark 2.
► Select the type of view:
reversing.
• "Standard view".
When the function is activated, it is possible
• "180° view".
that the view from above is not displayed. If
157
Driving
the system is activated when the vehicle has
AUTO mode
The red line 2 represents a distance of 30 cm
already moved, the view from above can be fully
from the rear bumper; the two blue lines 3 and 4
displayed.
represent 1 m and 2 m, respectively.
This view is available with AUTO mode or in the
Visiopark 1
view selection menu.
Rear view
Zoom view
This mode is activated by default.
Using sensors in the rear bumper, the automatic
view changes from the rear view (standard) to
the view from above (zoom) as an obstacle is
approached at the level of the red line (less than
30 cm) during a manoeuvre.
Standard view
To activate the camera located on the tailgate,
engage reverse gear and do not exceed a speed
The camera records the vehicle's surroundings
of 6 mph (10 km/h).
during the manoeuvre in order to create a
The system is deactivated:
view from above the rear of the vehicle in its
- Automatically, at speeds above approximately
near surroundings, allowing the vehicle to be
6 mph (10 km/h),
manoeuvred around nearby obstacles.
- Automatically, if the tailgate is opened.
This view is available with AUTO mode or in the
- Upon changing out of reverse gear (the image
view selection menu.
remains displayed for 7 seconds).
Obstacles may appear further away than
- By pressing the white arrow in the upper-left
The area behind the vehicle is displayed on the
they actually are.
corner of the touch screen.
screen.
It is important to monitor the sides of the
The blue lines 1 represent the width of your
vehicle during the manoeuvre, using the
vehicle, with the mirrors unfolded; their direction
mirrors.
changes according to the position of the steering
Parking sensors also provide additional
wheel.
information about the area around the vehicle.
158
Driving
180° view
offering views from the rear of the vehicle (rear
The rear vision views are similar to those for the
6
vision) when reverse gear is engaged and views
Visiopark 1 function.
from the front of the vehicle (front vision) when
For more information on the Visiopark
the gearbox is in neutral or a gear is engaged.
1 function, refer to the corresponding section.
Rear vision
Front and rear vision
The system activates automatically when
With the engine running and the speed
The 180° view facilitates reversing out of a
reverse gear is engaged.
below 12 mph (20 km/h), the system is
parking space, making it possible to see the
The system is deactivated:
activated via the Driving/Vehicle touch screen
approach of vehicles, pedestrians and cyclists.
- Automatically, at speeds above approximately
menu:
This view is not recommended for carrying out a
12 mph (20 km/h).
► Select "Visual parking assistance".
complete manoeuvre.
- When shifting out of reverse (the front vision
AUTO mode is displayed by default, with front
It features 3 areas: left A, centre B and right C.
image replaces the rear vision image for 7
vision, if the gearbox is in neutral or with a
This view is only available via the view selection
seconds).
gear engaged, or with rear vision, if reverse is
menu.
- By pressing the white arrow in the upper-left
engaged.
corner of the touch screen.
The system is deactivated:
Visiopark 2
- Automatically above about 19 mph (30 km/h)
If a trailer or a bicycle carrier is fitted to
The vehicle has a camera at the front, fitted in
(the image disappears temporarily from 12 mph
the towball, the area behind the vehicle
the grille, and a camera at the rear, located close
(20 km/h)).
on the view from above goes dark.
to the tailgate opening control.
- By pressing the white arrow in the upper-left
The surroundings are reconstructed by the
Using these cameras, the system displays the
corner of the touch screen.
front camera only.
vehicle's near surroundings on the touch screen,
159
Driving
AUTO mode
The red line 2 represents a distance of 30 cm
180° view
from the front bumper; the two orange lines 3
and 4 represent 1 m and 2 m, respectively.
This view is available with AUTO mode or by
selecting it in the view change menu.
Zoom view
This mode is activated by default.
Using sensors in the front bumper, the automatic
view changes from the front view (standard) to
the view from above (zoom) as an obstacle is
approached during a manoeuvre.
Standard view
The 180° view assists with exiting from a parking
The camera records the vehicle's surroundings
space in forward gear, making it possible to
during the manoeuvre in order to create a
see the approach of vehicles, pedestrians and
view from above the front of the vehicle in its
cyclists.
near surroundings, allowing the vehicle to be
This view is not recommended for carrying out a
manoeuvred around obstacles nearby.
complete manoeuvre.
This view is available with AUTO mode or in the
It consists of 3 areas: left A, centre B and right
view selection menu.
C.
This view is available only from the view
The area in front of your vehicle is displayed on
Obstacles may appear further away than
selection menu.
the screen.
they actually are.
The orange lines 1 represent the width of your
It is important to check the sides of the
vehicle, with the mirrors unfolded; their direction
vehicle during the manoeuvre, using the
changes according to the position of the steering
mirrors.
wheel.
The parking sensors also supplement the
information on the vehicle's surroundings.
160
Driving
Park Assist
B. Exit from a "parallel" parking space
The Parking sensors function is not
6
C. Entry into a "bay" parking space
available during parking space
For more information, refer to the
measurement. It intervenes later when
General recommendations on the use
The Park Assist system cannot operate
manoeuvring to warn that the vehicle is
of driving and manoeuvring aids.
with the engine switched off.
approaching an obstacle: the audible signal
When Park Assist is activated, it prevents
becomes continuous when the obstacle is
This system provides active parking assistance:
less than 30 centimetres away.
Stop & Start from going into STOP mode. In
it detects a parking space then operates the
If the Parking sensors function has
STOP mode, activation of Park Assist restarts
steering system to park in this space.
been deactivated, it will be automatically
the engine.
With a manual gearbox, the driver manages the
reactivated during the assisted manoeuvring
accelerator, brakes, gears and clutch.
phases.
The Park Assist system takes control of
With an automatic gearbox (EAT6/EAT8), the
the steering for a maximum of 4
driver manages the accelerator, brakes and
manoeuvring cycles. It is deactivated after
During parking and exit from parking
gears.
these 4 cycles. If the vehicle is not positioned
manoeuvres, the Visiopark 1 - Visiopark
During phases of entry into and exit from a
correctly, take back control to complete the
2 functions may come into operation. They
parking space, the system provides visual and
manoeuvre.
allow better monitoring of the surroundings of
audible information to the driver in order to make
the vehicle, by displaying additional
the manoeuvres safe. Several forward and
information in the touch screen.
The sequence of manoeuvres and the
reverse manoeuvres may be required.
For more information on the Visiopark
driving instructions are displayed in the
At any time, the driver can take back control by
1 - Visiopark 2 functions, refer to the
instrument panel.
holding the steering wheel.
corresponding section.
The assistance is activated: the display
of this symbol and a speed limit
indicate that the steering manoeuvres are
In some circumstances, the sensors may
controlled by the system: do not touch the
not detect small obstacles located in their
steering wheel.
blind spots.
The assistance is deactivated: the
Any object exceeding the size of the vehicle
display of this symbol indicates that the
(e.g. roof ladder, towball) is not taken
steering manoeuvres are no longer controlled
into account by the Park Assist during a
by the system: take over the steering.
manoeuvre.
The Park Assist system provides assistance for
the following manoeuvres:
Activation of Park Assist deactivates the
A. Entry into a "parallel" parking space
Blind spot monitoring.
161
Driving
Always check the surroundings of the
► Drive at a speed below 12 mph (20
at a distance of between 0.5 m and 1.5 m from
20
vehicle before starting a manoeuvre.
km/h) following the instructions until the
the row of parked vehicles.
If the lateral distance between the vehicle and
system finds an available space.
► Drive at a speed below 12 mph (20
20
the space is too great, the system may not be
► Move forwards slowly until a message
km/h) following the instructions until the
able to measure the space.
is displayed, accompanied by an audible
system finds an available space.
signal, asking you to engage reverse gear.
When several successive spaces are
During manoeuvring phases, the steering
► Engage reverse gear, release the
found, the vehicle will be directed
wheel performs rapid turns: do not hold
steering wheel and move without
towards the last one.
the steering wheel or put your hands between
exceeding a speed of 4 mph (7 km/h).
the spokes of the steering wheel.
The assisted parking manoeuvre is in
► Move forwards slowly until a message
Beware of any object likely to block the
progress.
is displayed, accompanied by an audible
manoeuvre (e.g. loose clothing, scarves, ties)
► Without exceeding 5 mph (7 km/h),
signal, asking you to engage reverse gear.
7
- risk of injury!
move forwards and backwards, aided by
► Engage reverse gear, release the
the warnings from the "Parking sensors" system,
steering wheel and move without
until the end of the manoeuvre is indicated.
exceeding the speed of 5 mph (7 km/h).
Assistance with "parallel"
The end of the manoeuvre is confirmed
The assisted parking manoeuvre is in
parking manoeuvres
by a message and an audible signal.
progress.
Parking assistance is deactivated: you can take
► Without exceeding 5 mph (7 km/h),
► When parking, select "Park Assist" in
over the controls again.
7
the Driving/Vehicle touch screen menu
follow the instructions and the warnings
to activate the function.
from the "Parking sensors" system, until the end
Assistance with "bay"
► Limit the vehicle speed to a maximum
of the manoeuvre is indicated.
of 12 mph (20 km/h) and select "Enter
parking manoeuvres
The end of the manoeuvre is confirmed
parallel parking space" on the touch screen.
► When parking, select “Park Assist” in
by a message and an audible signal.
The system is deactivated: it is possible to retake
the Driving/Vehicle touch screen menu
To enter a "parallel" parking space, the
control.
to activate the function.
system does not identify spaces that are
► Limit the vehicle speed to a maximum
During a "bay" parking manoeuvre, the
clearly smaller or larger than the vehicle.
of 12 mph (20 km/h) and select “Enter
Park Assist system is automatically
► Operate the direction indicator on the
bay parking space” on the touch screen.
deactivated once the rear of the vehicle is
side you have chosen to park in order to
► Operate the direction indicator on the
within 50 cm of an obstacle.
activate the measurement function. The vehicle
parking side chosen to activate the
must drive at a distance of between 0.5 m and
measurement function. The vehicle should drive
1.5 m from the row of parked vehicles.
162
Driving
Assistance with "parallel"
- if the engine stalls.
In the event of a malfunction, have the system
6
- if the driver's seat belt is not fastened.
checked by a PEUGEOT dealer or a qualified
parking exit manoeuvres
- on opening the driver's door.
workshop.
► To leave a "parallel" parking space, switch
- if no manoeuvre is performed within 5 minutes
In the event of a power steering
the engine on.
of selecting the type of manoeuvre.
malfunction, this warning lamp is
► With the vehicle stationary, select
- after a prolonged stop of the vehicle during a
displayed on the instrument panel, accompanied
"Park Assist" in the Driving/Vehicle
manoeuvre.
by a warning message.
touch screen menu to activate the function.
- if the wheel anti-slip regulation (ASR) is
You must stop as soon as it is safe to do so.
► Press "Exit parking slot" on the touch
triggered.
Contact a PEUGEOT dealer or a qualified
screen.
- if the speed of the vehicle is above 43 mph
workshop.
► Operate the direction indicator for the
(70 km/h).
exit side chosen.
- when the driver interrupts the rotation of the
► Engage reverse or forward
steering wheel.
gear and release the steering
- after 4 manoeuvring cycles.
wheel.
- if one of the front wheels encounters an
The assisted parking manoeuvre is in
obstacle.
progress.
- when towing a trailer, connected electrically.
► Without exceeding 3 mph (5 km/h),
Deactivation is confirmed by a message and an
5
move forwards and backwards, aided by
audible signal.
the warnings from the "Parking sensors" system,
The driver should then take back control of the
until the end of the manoeuvre is indicated.
vehicle's steering.
The manoeuvre is complete when the vehicle's
If the system is deactivated during a
front wheels are clear of the parking space.
manoeuvre, the driver should reactivate
The end of the manoeuvre is confirmed
it to repeat the measurement.
by a message and an audible signal.
The system is deactivated: it is possible to retake
To switch the system off for a prolonged period,
control.
contact a PEUGEOT dealer or a qualified
workshop.
Deactivation
The system is deactivated via the Driving /
Malfunctions
Vehicle touch screen menu.
If the parking sensor malfunction occurs
The system is automatically deactivated:
during use, indicated by this warning lamp
– when the ignition is switched off.
coming on, it causes the function to deactivate.
163
Peugeot & TotalEnergies,
a partnership in performance !
For more than 25 years of partnership, TotalEnergies and Peugeot have
pushed the limits of performance in sports competition with historic
victories, in endurance races or in rallies. Today, the two brands continue
their common motorsport adventure by setting out to conquer the 24h
of Le Mans and the FIA World Endurance Championship in the Hybrid
Hypercar category. So many challenges for which Peugeot exclusively
recommends high-tech Quartz lubricants for the protection of its
engines throughout their life. TotalEnergies therefore equips Peugeot
vehicles with Quartz lubricants from their first filling in the factory to the
approved maintenance networks to guarantee them optimal day-to-
day operation. Peugeot & TotalEnergies: official partners in performance !
Keep your engine younger for longer !
Quartz Ineo Xtra First 0W-20 is a very high performance lubricant
resulting from the joint work of the Peugeot and TotalEnergies R&D
teams. Its innovative technology extends your engine’s life while
reaching significant fuel savings and thus limiting CO2 emissions. The
product is now available in new packaging* made of 50% recycled
material and 100% recyclable.
* 1L & 5L produced in Europe
Practical information
fuels could prevent the engine from operating
panel, accompanied by the display of a message
Compatibility of fuels
7
correctly. In these temperature conditions, use
and an audible signal. When it first comes on,
winter-type Diesel fuel and keep the fuel tank
about 6 litres of fuel remain.
more than 50 % full.
Until sufficient fuel is added, this warning lamp
Petrol fuels conforming to the EN228 standard
At temperatures below -15 °C (+5 °F) to avoid
appears every time the ignition is switched on,
containing up to 5% and 10% ethanol
problems starting, it is best to park the vehicle
accompanied by the message and the audible
respectively.
under shelter (heated garage).
signal. When driving, this message and audible
signal are repeated with increasing frequency as
Travelling abroad
the fuel level drops towards 0.
Diesel fuels conforming to the EN590, EN16734
Certain fuels could damage your vehicle’s
You must refuel as soon as possible to avoid
and EN16709 standards and containing up to
engine.
running out of fuel.
7%, 10%, 20% and 30% fatty acid methyl ester
In certain countries, the use of a particular
For more information on Running out of fuel
respectively. The use of B20 or B30 fuels, even
fuel may be required (specific octane rating,
(Diesel), refer to the corresponding section.
occasionally, imposes special maintenance
specific trade name, etc.) to ensure correct
A small arrow by the warning lamp
conditions referred to as "Arduous conditions".
operation of the engine.
indicates on which side of the vehicle the
For all additional information, consult a dealer.
fuel filler flap is located.
Paraffinic Diesel fuel conforming to the EN15940
Refuelling
Stop & Start
standard.
Never refuel with the engine in STOP
The use of any other type of (bio) fuel
mode; you must switch off the ignition.
Fuel tank capacity:
(e.g. pure or diluted vegetable or animal
approximately 53 litres
oils, domestic fuel) is strictly prohibited - risk
(Petrol or Diesel) or 43 litres
Refuelling
of damaging the engine and fuel system!
(Rechargeable hybrid).
Any addition of fuel must be in quantities of at
least 10 litres, in order to be registered by the
The only fuel additives authorised for use
Fuel tank capacity:
fuel gauge.
are those that meet the B715001 (Petrol)
approximately 56 litres.
Opening the filler flap may create a noise caused
or B715000 (Diesel) standards.
Reserve level: approximately 6 litres.
by an inrush of air. This vacuum is entirely
normal, resulting from the sealing of the fuel
Diesel at low temperature
Low fuel level
system.
The filler cap is built into the filler flap or must be
At temperatures below 0 °C (+32 °F), the
When the low fuel level is reached, this
unscrewed (depending on version).
formation of paraffins in summer-type Diesel
warning lamp lights up on the instrument
165
Practical information
To refuel in complete safety:
Misfuel prevention (Diesel)
► Always switch off the engine.
(Depending on country of sale.)
This mechanical device prevents filling the tank
of a Diesel vehicle with petrol.
Located in the filler neck, the misfuel prevention
device is visible when the filler cap is removed.
► Turn the filler cap to the left, remove it
Operation
and place it on its support on the filler flap
► To open the filler flap, press the flap opening
(depending on version).
button for more than 2 seconds or, with the
► Insert the filler nozzle and push it in as far as
vehicle unlocked, press the rear of the filler flap
possible before starting to refuel (to minimise the
(depending on version).
risk of splashing).
► Fill the tank.
Rechargeable hybrid vehicles
Do not continue after the nozzle’s third cut-
After pressing the button on the
out. Doing so may cause malfunctions.
dashboard, the filler flap may not open for
► Put the filler cap back in place and turn it to
several minutes. A sound is emitted when the
the right (depending on version).
filler flap opens.
► Push the fuel filler flap to close it.
If the flap becomes stuck, press and hold
The vehicle is fitted with a catalytic converter,
the button on the dashboard for more than
which helps to reduce the level of harmful
When a petrol filler nozzle is introduced into the
3 seconds.
emissions in the exhaust gases.
fuel filler neck of a Diesel vehicle, it comes into
► Select a pump that delivers the correct fuel
For petrol engines, you must use unleaded
contact with the flap. The system remains closed
type for the vehicle's engine (see a reminder
fuel.
and prevents filling.
label on the inside of the filler flap).
The filler neck is narrower, allowing only
Do not persist but introduce a Diesel type
unleaded petrol nozzles to be inserted.
filler nozzle.
If you have put in the wrong fuel for
The misfuel prevention device does not
the vehicle, you must have the fuel
prevent filling with a jerrycan, regardless
tank drained and filled with the correct fuel
of the fuel type.
before starting the engine.
166
Practical information
Travelling abroad
High voltage system voltage is
Damage to the vehicle or the traction battery
7
As Diesel fuel pump nozzles may be
dangerous and can cause burns or other
could result in the leakage of toxic gases or
different in other countries, the presence
injuries or even fatal electric shock.
fluids either immediately or later. PEUGEOT
of the misfuel prevention device may make
Since damage to high voltage components is
recommends that you:
refuelling impossible.
not visible, PEUGEOT recommends that you:
- Always inform the fire and emergency
Before travelling abroad, it is advisable to
- Never touch the components, damaged
services in the event of an incident, warning
check with a PEUGEOT dealer if the vehicle
or not, and never let your jewelry or other
that the vehicle is equipped with a traction
is suitable for the distribution equipment of the
metallic objects come into contact with these
battery.
countries visited.
components.
- Never touch the liquids leaking from the
- Never work on the orange high voltage
traction battery.
cables or on any other high voltage
- Do not inhale the gases emitted by the
Rechargeable hybrid
component marked with the Electric risk label.
traction battery which are toxic.
Any intervention on the high voltage system
- Move away from the vehicle in the event of
system
must be carried out by qualified persons in
incident or accident, the gases emitted being
workshops qualified and approved to carry
flammable and could cause a fire.
Electrical system
out this type of work.
The electrical circuit of the rechargeable hybrid
- Never damage, modify or remove the
system is identified by orange cables and its
orange high voltage cables or disconnect
components are marked with this symbol:
them from the high voltage network.
- Never open, modify or remove the cover of
the traction battery.
- Never work with cutting and forming
This label is intended solely for use by
tools or heat sources near high voltage
firefighters and maintenance services in
components and cables.
the event of any work on the vehicle.
In case of low level of fluid in the cooling
No other person must touch the device shown
tank, the refilling shall only be performed in a
The rechargeable hybrid powertrain uses
on this label.
qualified and trained workshop to verify that
a voltage of between 240 V and 400 V.
the leakage is not in the traction battery.
This system may be hot both when the
Any intervention on the high voltage system
In the event of an accident or impact
ignition is on and after switching it off.
must be carried out by qualified persons in
to the vehicle’s underbody
Comply with the warning messages shown
workshops qualified and approved to carry
In these situations, the electrical circuit or the
on the labels, particularly inside the charging
out this type of work.
traction battery can be seriously damaged.
flap.
167
Practical information
Stop as soon as it is safe to do so and switch
It is located under the rear seats.
In the event of damage to the traction
off the ignition.
The traction battery's range varies depending
battery
Contact a PEUGEOT dealer or a qualified
on the type of driving, the route, the use of
It is strictly prohibited to work on the vehicle
workshop.
thermal comfort equipment and the ageing of its
yourself.
components.
Do not touch liquids coming from the battery,
When washing
and in the event of skin contact with these
The traction battery ageing depends on
Before washing the vehicle, always
products, wash abundantly with water and
several factors, such as climatic
check that the charging flap is closed
contact a doctor as soon as possible.
conditions and the distance travelled.
correctly.
Contact a PEUGEOT dealer or a qualified
Never wash the vehicle while the battery is
workshop to have the system checked.
To preserve the mileage of your vehicle
on charge.
and the durability of your traction battery,
PEUGEOT recommends that you:
Disposal of the traction battery
High-pressure washing
- Do not fully charge the battery of your
The traction battery is designed for the life of the
To avoid damaging the electrical
electric vehicle daily (charge the traction
vehicle if the recommendations of PEUGEOT
components, it is expressly prohibited to
battery below 80% as often as possible).
are followed.
use high-pressure washing in the engine
- Do not completely discharge the battery.
If it becomes necessary to replace the battery,
compartment or under the body.
- Do not store the vehicle for a long period
contact the PEUGEOT dealer for instructions on
Do not use a pressure greater than 80 bar
of non-use (more than 12 hours) when the
its disposal. Improper disposal carries the risk of
when washing the bodywork.
traction battery has a low or high charge level.
severe burns, electric shock, and damage to the
Prefer a charge level between 20 and 40%.
environment.
Never allow water or dust to enter the
- Limit the use of fast charging.
In accordance with regulations, PEUGEOT
connector or charging nozzle - risk of
- Do not expose the vehicle to temperatures
ensures a second life or recycling of this
electrocution or fire!
below -30°C and above +60°C for more than
component in collaboration with qualified
Never connect / disconnect the charging
24 hours.
operators.
nozzle or cable with wet hands - risk of
- Avoid charging the vehicle at negative
electrocution!
temperatures (except if the vehicle ran more
Charging flap
than 20 minutes) or above +30°C.
The charging flap is located on the rear left-hand
- Do not use the vehicle's traction battery as
side of the vehicle.
Traction battery
a generator of energy.
The Li-ion (Lithium-ion) traction battery stores
- Do not use a generator to recharge your
the electrical energy needed to propel the
vehicle's traction battery.
vehicle.
168
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст