Peugeot 807 (2013 year). Instruction — part 5

EASE OF USE and COMFORT

3

63

Seats

Memorising seat positions

Two driving positions can be

memorised, using buttons M/1 and

M/2 .
These are located on the side of the

seat:
- Place the ignition key in the

"running" position (2nd notch),

- Adjust your seat,
- Press button M , then button 1 for

a fi rst driving position within four

seconds.

Repeat the same actions on buttons M

and 2 to store another driving position.
An audible signal confi rms that a

position has been memorised.
Memorising a new position cancels the

previous one.

Activating a memorised driving

position

Front heated seat controls

When the engine is running, the front

seats can be heated separately.
Use the adjustment controls located on

the side of each front seat to switch on

and select the self-regulated level of

heating:
1: Low.
2: Medium.
3: High.
0: Off.

After recalling a memorised

position fi ve times in succession,

the function will be cancelled until

the engine is started.

Engine running
- Keep button 1 or 2 pressed down

until the end of setting of the

corresponding memorised position.

Engine off
- Briefl y press button 1 or 2 to recall

the corresponding memorised

position.

64

Seats

Rear bench seat

One three-seat bench seat, row 3.

Rear side seats

Two rear passenger seats, left and right side position,

rows 2 and 3.

Rear centre seat

One rear passenger seat, row 2 central position and

row 3 left side position. Integrated seat belt. Plastic shell

trim. Folds to the low table position.

EASE OF USE and COMFORT

3

65

Seats

REAR SIDE SEATS

Forwards/backwards adjustment
Lift bar A and slide the seat forwards

or backwards.

Handling the side seat

Adjusting the angle of the seat back
Push lever B upwards and adjust the

angle as required.
Release the lever to lock.

Access to row 3
1. Place the head restraint in the low

position.

2. Push lever B upwards as far as

possible.

Exit from row 3
1. Place the head restraint in the low

position.

2. Pull control C .
3. Guide the tilting of the seat back

forwards until the rear anchorages

are unlocked. If you experience any

diffi culty, use the red emergency

control to unlock the anchorages.

4. Place the seat in the vertical closed

position.

Following each entry or exit,

reposition the raised seat guiding

it until the rear anchorages lock in

their rails.

3. Fold the seat back onto the seat

cushion and guide the tilting of the

seat back forwards until the rear

anchorages are unlocked. If you

experience any diffi culty, use the

emergency control to unlock the

anchorages.

4. Place the seat in the vertical closed

position.

66

Seats

Control for sliding the rear side

seats from row 3 or the boot
Pull the strap (marked with the arrow

symbol) to slide the seat in front of you.

Removing the side seat

1. Tilt the seat back forwards to

detach the rear anchorages.

2. Grab the red strap which appears

and pull it upwards, the front

anchorages unlock .

3. The strap, like the handle, enables

you to remove the seat.

Refi tting the side seat

Check that there is no obstacle

obstructing the slides or

preventing correct locking of the

seat anchorages.

1. Place the front anchorages at the

front stop in the slides. Support the

strap fi rmly for easier positioning of

the seat.

2. Tilt the folded seat towards the rear.

The rear anchorages lock.

3. Raise the seat back.
4. Slide the seat .

EASE OF USE and COMFORT

3

67

Seats

ROW 2 CENTRE SEAT

This can be placed in row 3, on the left.

"Low table" position
1. Place the head restraint in the low

position.

2. At the top (at the back of the seat),

lift the handle identifi ed by the

symbol and guide the tilting of the

seat back towards its seat cushion.

3. You have a "low table". To return to

the seat position, lift the handle and

guide the raising of the seat back.

Removing the centre seat
1. Place the seat in the "low table"

position.

2. Using the control which you pull, tilt

the seat back forwards so releasing

the rear anchorages from the

slides.

3. Grab the red strap which appears

and pull it upwards, the front

anchorages unlock .

4. The strap, like the handle, enables

you to remove the seat.

68

Seats

Rear head restraints

The rear head restraints can be

removed and have two positions:
- high, position for use,
- low, storage position.

To raise or lower a head restraint, pull

it forwards sliding it at the same time.
To remove it, place it in the high

position, push the lug and pull it

forwards and upwards.
To refi t it, engage the head restraint

rods in the holes taking care to remain

in the centreline of the seat back.

Never drive with the head

restraints removed, they must be

in place and correctly adjusted.

Refi tting the centre seat

Check that there is no obstacle

obstructing the slides or

preventing correct locking of the

seat anchorages.

1. Place the front anchorages at the

front stop in the slides. Support the

strap fi rmly for easier positioning of

the seat.

2. Tilt the folded seat towards the rear.

The rear anchorages lock.

3. Raise the seat back and slide the

seat.

Turning a rear seat round
The rear seats can be placed in a "face

to face" position.
Carry out the operations described for

removal then turn the seat round and

resume with the procedure for refi tting

the seat .

This turning operation must be

carried out when stationary.

Driving with a passenger seated facing

the rear is prohibited.
When the vehicle is being driven,

placing a row 2 seat in the closed

position while a passenger is sitting in

row 3 is prohibited.

EASE OF USE and COMFORT

3

69

Seats

REAR BENCH SEAT

From the boot, you can pull

on strap B and slide the seat

forwards to make it easier to load

the vehicle.

The rear bench seat must only be

fi tted in row 3.

Seat back folded position
1. Place the head restraints in the low

position.

2. Pull the strap C upwards, from the

tailgate.

3. Tilt the seat back on the seat

cushion.

Vertical position of the bench seat
1. Place the head restraints in the low

position.

2. Pull the strap C upwards, from the

tailgate.

3. Fold the seat back onto the seat

cushion.

4. Pull the lever D to unlock the rear

anchorages.

5. Place the seat in the vertical

"folded" position.

When driving, attach the retaining

straps to the handles.

Forwards/backwards

adjustment

From the seat cushion, lift bar A and

slide the seat towards the front or the

rear.

70

Seats

Removing the bench seat
1. Fold the seat to the vertical

position.

2. Grasp the two bars E underneath

the seat.

3. The front anchorages unlock.

Refi tting the bench seat

For removal and refi tting, pass the

rear seat, in the "folded" position,

through the sliding side doors.

Check that there is nothing

blocking the runners which could

prevent correct locking of the

bench seat anchorages.

1. Position the front anchorages at the

front stop of the runners.

2. Tilt the folded seat rearwards.
3. The rear anchorages then lock.
4. Unlock the seat back and lift it

using the strap C .

Good practice

When the vehicle is being driven, it is

prohibited for a passenger to sit:
-

in row 3 if the seat back in front

(row 2) is in the table position.

-

in row 3 if the seat/bench in front

(row 2) is in the vertical folded

position.

-

in the centre seat if the right-hand

side seat is in the vertical folded

position.

EASE OF USE and COMFORT

3

71

Seats

The centre seat may be installed

in the central position in row 2 and

in the left side position in row 3.

MODULARITY AND POSSIBLE SEAT CONFIGURATIONS

Examples of various

arrangements combining

pleasure and practicality:

The various operations modifying

the existing confi guration must

be carried out with the engine

switched off (See section on "Seats").
It is prohibited to be in a rearwards

facing position when the vehicle is

being driven.
The rotating of the seats depends on

the vehicle equipment and the country.

5 seats with picnic position when

parked

5 seat arrangements

72

Seats

7 seats with access to row 3

8 seats with bench seat

EASE OF USE and COMFORT

3

73

Seats

"Cargo"/Transportation of long objects confi guration

EASE OF USE and COMFORT

3

75

Practical information

FRONT SEAT LAYOUT

Storage drawers
There is a storage drawer under each

front seat.
-

To open it, lift and pull.

-

To take it out, open it to its full

extent, lift the two tabs on either

side of the drawer, then remove it

completely.

PRACTICAL INFORMATION

'Aircraft' type table
You have an 'aircraft' type table with a

rim, equipped with a cup holder, fi tted

to the rear of each front seat.
Do not forget to fold this before pivoting

the seat.

12V socket
You have a 12 V accessory socket

(120 W) at the foot of the driver's seat,

which is accessible to passengers of

row 2.

Front and rear armrests

To place the armrest in its rest

position:
-

Lift the armrest until it is aligned

with the seat back.

Each front seat also has a storage

pocket on the seat back.

To place the armrest in the position

in which it is used:
-

Push it towards the rear,

-

Fold it down completely,

-

Raise it slowly to the required

position,

-

If you lift it past the required

position, restart the above

operations.

76

Practical information

EASE OF USE and COMFORT

3

77

Practical information

1. Driver's upper glove box

FRONT INTERIOR LAYOUT

This is fi tted with a lock.
To open the glove box, lift the handle.
The light comes on when the cover is

opened.
It contains three sockets for the

connection of video equipment and

access to the fascia fuse box.
It includes special compartments for

storing maps, a packet of cigarettes,

an A4 document etc.
RCA sockets.

This permits the connection of a mobile

telephone charger, a baby's bottle

warmer, etc.

To open, press the button.
To close, press the cover.
It includes special compartments for

storing a pen, a mobile telephone,

coins or tokens and credit cards.

2. Audio equipment concealing fl ap

Lower the fl ap fully to lock it in place.
Press the fl ap to raise it.

3. Central storage compartment

4. Passenger's upper glove box

To open, press the button.
To close, press the cover.
It includes special compartments for

storing a pair of spectacles, keys, fi ve

CDs and four audio cassettes or nine

audio CDs.

5. Passenger's lower glove box

6. Lighter or 12 V socket for

accessories (120 W)

12. Mat fi tting/removal
When removing the front mat, push

the seats as far back as possible and

remove the fi xings.
When refi tting, position the mat

correctly on the pins and clip the

fi xings. Check that the mat is secured

correctly.
To prevent the mat from becoming

caught under the pedals:
-

only use mats suited to the fi xings

already present in the vehicle. It

is imperative that these fi xings are

used.

- never

fi t one mat on top of another.

7. Cooled compartment

It can hold up to three cans.
Slide the closer, located on the right, to

open (upwards) or close (downwards)

the air inlet.

8. Can holder and ashtray

This retractable and lit support contains

up to two can holders, a removable

ashtray and a location for the lighter

when it is used as a 12 V socket

(120 W).

9. Storage compartment or

additional telematics control

The storage compartment must not be

used as an ashtray.
If fi tted on your vehicle, the additional

telematics control is located on the

centre console.

10. Storage compartment

11. Door tray with space for a bottle

of water

Bluetooth.

78

Practical information