Peugeot 5008 (2017 year). Instruction — part 8
3
111
Ease of use and comfort
Sun visor
Component which protects against sunlight
from the front or the side, also equipped with an
illuminated vanity mirror.
Glove box
F To open the glove box, raise the handle.
The glove box is lit when the lid is opened.
F With the ignition on, raise the concealing
flap; the mirror is illuminated automatically.
This sun visor is also equipped with a ticket
holder.
It houses the front passenger airbag
deactivation switch A.
It also gives access to the housing for scented
air freshener B cartridges.
Never drive with the glove box open when
a passenger is at the front – it may cause
injury during sharp deceleration!
Cigarette lighter/12 V
accessory socket(s)
You can use this socket to connect a telephone
charger, a bottle warmer, etc.
After use, put the cigarette lighter back into
place straight away.
The connection of an electrical device
not approved by PEUGEOT, such as a
USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor telephone
reception or interference with displays in
the screens.
F To use the cigarette lighter, press it in
and wait a few seconds until it pops out
automatically.
F To use a 12 V accessory (max power:
120 W), remove the cigarette lighter and
connect a suitable adaptor.
112
Ease of use and comfort
USB port
The USB port also allows a smartphone to be
connected by MirrorLink™ or CarPlay
®
, so that
certain applications on the smartphone can be
used in the touch screen.
FOCAL
®
premium Hi-Fi
system
10 speakers incorporating exclusive FOCAL
®
technologies offer the pleasure of pure and
detailed sound inside the vehicle:
- High fidelity woofer / mid-range speakers:
Polyglass technology delivering balance
and precise sound.
- TNF tweeters: Inverted dome aluminium
technology giving optimum sound
dispersion and very detailed treble.
- Sub-woofer: 200 mm triple coil Power
Flower™ technology for defined and
dynamic reproduction of low frequencies.
- 12-way active amplification – 515 Watts:
Hybrid Class AB / Class D technology
providing breadth and finesse in the high
frequency signals, as well as real power in
the bass.
Wireless charger
This system allows the wireless charging of a
portable device, such as a smartphone, using
the principle of magnetic induction, based on
the Qi 1.1 standard.
The portable device to be charged must be
compatible with the Qi standard, either by
design or by using a compatible holder or shell.
The charging zone is identified by the Qi
symbol.
The USB port allows the connection of a
portable device, such as an iPod
®
-type digital
audio player, or a USB memory stick.
The USB reader reads your audio files which
are then transferred to the audio system and
played via the vehicle’s loudspeakers.
These files are managed via the steering wheel
controls or from the audio system.
When connected to the USB port,
the portable device can be charged
automatically.
While charging, a message is displayed
if the power consumption of the portable
device exceeds the amperage supplied by
the vehicle.
For more details on the Audio equipment and
telematics, and particularly the USB port,
consult the corresponding section.
Your vehicle is equipped with a high-fidelity
sound system designed by the French brand
FOCAL
®
, a specialist in acoustics for more
than 35 years and recognised throughout the
world for its patented innovations and its unique
audio signature.
3
113
Ease of use and comfort
Operation
The charger works with the engine running and
in STOP mode of Stop & Start.
Charging is managed by the smartphone.
For versions with Keyless Entry and Starting,
operation of the charger may be interrupted
when opening a door or switching off the
ignition.
Charging
F First ensure that the charging zone is clear
of other articles.
F Place a portable device in the middle of the
charging zone.
F Once the portable device is detected, the
charge indicator lamp comes on in green.
The system only supports charging one
portable device at a time.
Do not leave any metal objects (coins,
keys, vehicle remote control, etc.) in
the charging area while a device is
being charged – risk of overheating or
interrupting the charging process!
Checking operation
F Charging of the portable device's battery
then starts.
F Once the portable device's battery is fully
charged, the charge indicator lamp goes off.
The state of the charge indicator lamp allows
the operation of the charger to be monitored.
Charge indicator
lamp
Meaning
Off
Engine switched off.
No compatible
portable device
detected.
Charging finished.
Fixed, green
Compatible portable
device detected.
Charging...
Flashing, orange
Foreign object
detected in the
charging zone.
Portable device not
well centred in the
charging zone.
Fixed, orange
Fault with the
portable device's
battery meter.
Temperature of the
portable device's
battery too high.
Charger fault.
114
Ease of use and comfort
If the indicator lamp is lit orange:
Front armrest
Comfort device for the driver and front
passenger.
It includes a refrigerated storage space.
Opening
Storage
Closing
Scented air freshener
A complete air freshener system for the
passenger compartment. It is supplied by a
three-fragrance cartridge.
This system operates only with the engine
running.
Activation / Settings
Activation and adjustment of settings is done in
the touch screen:
- either directly in the Applications menu,
- or by personalising an ambience for the
i-Cockpit Amplify function.
In the Applications menu:
- remove the portable device, then replace it
in the middle of the charging zone.
or
- remove the portable device and try again in
a quarter of an hour.
If the problem persists, have the system
checked by a PEUGEOT dealer or a qualified
workshop.
F Press the lever beneath the cover.
The cover opens in two parts.
The small removable tray can be installed in
front of or behind the storage space.
A ventilation nozzle circulates fresh air.
F Fold the two parts of the cover back.
F
Select "Scented air freshener",
F select a fragrance from the three offered,
F select a delivery intensity to activate the
system,
or
F select "OFF" to deactivate it.
The modifications are taken into account
immediately.
3
115
Ease of use and comfort
The scented air freshener is also
managed by the i-Cockpit Amplify
function.
For more information on the i-Cockpit Amplify
function, refer to the corresponding section.
Changing the cartridge
Access to the cartridge is in the glove box.
F Ignition on, pull the tab 1 in the direction of
the arrow to release the used cartridge.
F Remove the used cartridge 2 from its
housing.
The air freshener stops working with the
cartridge removed.
F Remove the two seals from the new
cartridge.
F Insert the new cartridge into its housing
observing the direction of fitment.
The air freshener is ready to operate again.
Recommendations
Do not discard the original cartridge, which
serves as a blanking plug if the air freshener is
not used.
Retain the cartridge sealing caps which serve
as packaging if the cartridge is not used.
Replacement cartridges are available from
PEUGEOT dealers or from the brand's internet
website.
As a safety measure:
- use only the cartridges designed for
the system,
- do not try to fit or remove a cartridge
when driving,
- do not try to refill or dismantle the
cartridges.
Keep cartridges out of the reach of
children or pets.
Do not allow the fluid in the cartridge to
come into contact with the skin or eyes.
In the event of ingestion of the fluid in the
cartridge, consult a doctor, showing them
the product packaging or label.
116
Ease of use and comfort
Removing
To remove the mat on the driver's side:
F move the seat as far back as possible,
F unclip the fixings,
F remove the mat.
Refitting
To avoid any risk of jamming of the pedals:
- only use mats which are suited to the
fixings already present in the vehicle;
these fixings must be used,
- never place one mat on top of another.
The use of mats not approved by
PEUGEOT may interfere with access to
the pedals and hinder the operation of the
cruise control / speed limiter.
The mats approved by PEUGEOT have
two fixings located below the seat.
Mats
Fitting
When fitting the mat for the first time, on the
driver's side use only the fixings provided in the
wallet attached.
The other mats are simply placed on the
carpet.
To refit the mat on the driver's side:
F position the mat correctly,
F reattach the fixings by pressing,
F check that the mat is secured correctly.
Courtesy lamps
1.
Front courtesy lamp
2.
Front map reading lamps
3.
Rear courtesy lamp
4.
Rear map reading lamps
3
117
Ease of use and comfort
Front and rear courtesy lamps
In this position, the courtesy
lamp comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when opening a door,
- when the remote control locking button is
activated, in order to locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
Permanently off.
Permanent lighting.
In "permanent lighting" mode, the lighting time
varies according to the circumstances:
- when the ignition is off, approximately ten
minutes,
- in energy saving mode, approximately thirty
seconds,
- with the engine running, unlimited.
When the front courtesy lamp is in the
"permanent lighting" position, the rear
courtesy lamp also comes on, except if it
is in the "permanently off" position.
To switch off the rear courtesy lamp, put it
in the "permanently off" position.
Front and rear map reading
lamps
Take care not to put anything in contact
with the courtesy lamps.
F With the ignition on, press the
corresponding switch.
Interior ambient lighting
The dimmed passenger compartment lighting
improves visibility in the vehicle when the light
is poor.
At night, the interior ambient lighting comes on
automatically when the sidelamps are switched
on.
118
Ease of use and comfort
The ambient lighting switches off automatically
when the sidelamps are switched off.
The interior ambient lighting can
be activated or deactivated and its
brightness adjusted in the Vehicle /
Driving menu of the touch screen.
The interior ambient lighting is also
managed by the i-Cockpit Amplify
function.
For more information on the
i-Cockpit Amplify function, refer
to the corresponding section.
Rear fittings
230 V / 50 Hz power socket
In the event of a fault, the green warning lamp
flashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Connect only one device at a time to
the socket (no extension or multi-way
connector).
Connect only devices with class II
insulation (shown on the device).
Do not use a device with a metal case
(electric shaver, etc.).
Depending on the version, the ambient lighting
includes:
- two LEDs located in the front courtesy lamp,
- a light source in the storage compartment at
the front of the centre console,
- a light source for each of the front footwells,
- illuminated guides on the front door panels
and on the sides of the centre console,
- illuminated bezels for the front cup holders,
- a light source for each of the front door
pockets,
- illuminated rails along the panoramic
sunroof blind.
It is located at the back of the centre console
beneath a protective cover.
This socket (max. power: 150 W) operates with
the engine running, as well as in STOP mode of
Stop & Start.
F Raise the protective cover.
F Check that the green indicator lamp is on.
F Connect your multimedia or other electrical
device (telephone charger, laptop computer,
CD-DVD player, bottle warmer, etc.).
As a safety measure, when electrical
consumption is high and when required by
the vehicle's electrical system (particular
weather conditions, electrical overload,
etc.), the current supply to the socket will
be cut off; the green indicator lamp goes
off.
3
119
Ease of use and comfort
12 V accessory socket
F To connect a 12 V accessory (max power:
120 W), lift the cover and connect a suitable
adaptor.
The connection of an electrical device
not approved by PEUGEOT, such as a
USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor telephone
reception or interference with displays in
the screens.
"Aircraft" type tables
Side blinds
Always guide the blind slowly using the
tab, both up and down.
F To use the table, lower it fully until it locks in
the low position.
F To store it, raise the table, passing the point
of resistance, to the high position.
On the passenger side, do not forget to
fold it before placing the backrest in the
table position.
For more information on the Front seats
and in particular setting the "table"
position for the backrest, refer to the
corresponding section.
Do not place hard or heavy objects on the
table.
They could become dangerous projectiles
in the event of emergency braking or
impact.
Fitted to the windows in row 2, they protect the
passenger compartment from the sun's rays.
F Pull the central tab to unroll the blind.
F Position the blind's clip on the hook.
120
Ease of use and comfort
Depending on version, the storage boxes are
fitted in the floor, at the foot of the side seats on
the second row.
On the left side, it may also contain the
temporary puncture repair kit.
To open them, lift the cover by the notch.
Storage boxes
Boot fittings
1.
Load space cover
2.
12 V accessory socket (maximum
power: 120 Watts)
3.
Boot lamp
4.
Luggage retaining strap
5.
Storage brackets of the load space
cover
6.
Armrest with cup holder and storage
7.
Open storage compartment
8.
Concertina floor
9.
Stowing rings
3
121
Ease of use and comfort
Load space cover
In 5-seat configuration, it is installed behind
the second row seats, with the third row seats
stored folded away.
In 7-seat configuration, it is stored behind the
third row seats.
Installation
Removal
F Remove the guides of the roller from the
rails in pillars B.
F Guide the roller as it reels in.
F Unlock the roller by pressing one of the
handles located at the ends of the roller
bracket.
F Position the left and right ends of the roller
in cut-outs A, with the mobile flap at the
front.
F Pull out the roller until it reaches the boot
pillars.
F Insert the guides of the roller into the rails in
pillars B.
Storage behind the 3
rd
row seats
F Make sure that the 3
rd
row seats are folded
away.
F Fold the first two concertina boards.
F Position the roller in the space located
above the armrest, side by side, tilting it
slightly.
F Slide the roller to the stop position, until it
reaches the notches arranged at the back of
the boot, with the two hinges facing down.
F Unfold the third row seats.
The folded concertina boards can be placed in
the horizontal or upright position.
To fold the 3
rd
row seats with the roller stored at
the back, it is necessary to raise the concertina
boards in order to give access to the seat
unlocking controls (red straps).
When sharp deceleration occurs, objects
placed on the load space cover can turn
into projectiles.
122
Ease of use and comfort
High load retaining net
It offers protection to the occupants when
very sharp braking occurs.
Behind the front seats
Once fitted, the net does not prevent
tipping of the backrests.
Behind the rear seats
This removable net allows the entire loading
volume to be used up to the roof:
- behind the front seats (1
st
row) when the
rear seats are folded down,
- behind the rear seats (2
nd
row) when the
load space cover is removed.
F Fold down the rear seats.
F Insert the ends of the bar, one after the
other, into the fixing points of the roof.
F Attach the net straps to the lower rings,
located on the outer slides of the front
seats.
F Pull on the straps to stretch the net.
F Remove the load space cover.
F Insert the ends of the bar, one after the
other, into the fixing points of the roof.
F Attach the straps of the net to the lower
rings, located on each side trim of the boot.
F Pull on the straps to stretch the net.
3
123
Ease of use and comfort
12 V accessory socket
The connection of an electrical device
not approved by PEUGEOT, such as a
USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor telephone
reception or interference with displays in
the screens.
Boot lighting
F To connect a 12 V accessory (max power:
120 W), remove the cap and connect an
appropriate adaptor.
F Switch on the ignition.
This comes on automatically when the boot is
opened and goes off automatically when the
boot is closed.
The lighting time varies according to the
circumstances:
- when the ignition is off, approximately
ten minutes,
- in energy economy mode,
approximately thirty seconds,
- with the engine running, unlimited.
124
Lighting and visibility
Exterior lighting control
stalk
Main lighting
Selection of main lighting mode
F Turn ring A to align the desired symbol with
the marking.
Automatic illumination of headlamps.
Daytime running lamps / Dipped
beam / Main beam.
Sidelamps only.
Dipped or main beam headlamps.
"Highway function"
On versions fitted with "Full LED"
technology headlamps, the range of the
dipped beam headlamps is automatically
increased once the speed of the vehicle is
above 70 mph (110 km/h).
Without AUTO lighting
With AUTO lighting
Headlamp dipping
F Pull stalk B towards you to switch between
dipped and main beam headlamps or to
activate automatic headlamp dipping.
In the lighting off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining a
pull on the stalk.
Displays
Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
Lighting off (ignition off) /
Daytime running lamps (engine
running).
A fault with a lamp is signalled by
the permanent illumination of this
warning lamp, accompanied by the
display of a message and an audible
signal.
125
4
Lighting and visibility
Foglamps
In clear weather or rain, during the day or
at night, it is prohibited to switch on the
front or rear foglamps. In these situations,
the power of their beams may dazzle other
drivers. They should only be used in fog
or snow.
In these weather conditions, it is your
responsibility to switch on the foglamps
and dipped beam headlamps manually as
the sunshine sensor may detect sufficient
light.
Switch off the foglamps when they are no
longer necessary.
Rear foglamps
The main or dipped beam headlamps
must be on.
Rotate and release ring C:
F forwards to switch on the rear foglamps.
F backwards to switch them off.
Front and rear foglamps
The sidelamps or dipped or main beam
headlamps must be on.
Rotate and release ring C:
F once forwards to switch on the front
foglamps,
F forwards a second time to switch on the rear
foglamps.
F once backwards to switch off the rear
foglamps,
F backwards a second time to switch off the
front foglamps.
126
Lighting and visibility
Switching off the lamps when the
ignition is switched off
On switching off the ignition, all of the
lamps turn off immediately, except for
dipped beam if automatic guide-me-home
lighting is activated.
Switching on the lamps after the
ignition is switched off
To reactivate the lighting control, rotate
ring A to the 0 position – lamps off, then to
the desired position.
On opening the driver's door a temporary
audible signal warns the driver that the
lighting is on.
They will go off automatically after a
period of time that depends on the state of
charge in battery (entering energy-saving
mode).
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal surface of the
glass of the headlamps and rear lamps is
normal; it disappears after the lamps have
been on for a few minutes.
Travelling abroad
If using your vehicle in a country that
drives on the other side of the road, the
headlamps must be adjusted to avoid
dazzling oncoming drivers.
Contact a PEUGEOT dealer or a qualified
workshop.
Daytime running lamps/
sidelamps
The LEDs of these lamps light up automatically
when the engine starts, at the front and back of
the vehicle.
They provide the following functions:
- Daytime running lamps (lighting control
stalk at position "0" or "AUTO" with
adequate light level).
- Sidelamps (lighting control stalk at position
"AUTO" with low light levels or "Sidelamps
only" or "Dipped/main beam headlamps").
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст