Peugeot 308 Dag (2007.5). Instruction — part 6
!
i
75
GLASS PANORAMIC ROOF
Component which has a tinted glass
panoramic surface to increase the light
and visibility in the passenger compart-
ment. Fitted with an electric shutter in
several sections to improve tempera-
ture and noise related comfort.
- manual mode
Pull or press control
A gently.
The shutter stops when you release
the control.
- automatic mode
Pull or press control
A firmly.
One press opens or closes the shutter
completely.
Pressing the control again stops the
shutter.
Safety auto-reverse
In automatic mode and at the end of its
travel, if the shutter meets an obstacle
while closing it stops and moves back
slightly.
One-touch electric shutter
There are two options for opening and
closing:
i
76
FUEL TANK
Capacity of the tank: approximately
60 litres.
To fill the tank safely:
it is essential that the engine is
switched off,
open the fuel filler flap,
insert the key in the cap, then turn it
to the left,
When filling is complete:
put the cap back in place,
turn the key to the right, then remove
it from the cap,
close the flap.
remove the cap and secure it on the
hook, located on the inside of the
flap,
fill the tank, but
do not continue
after the 3rd cut-off of the nozzle;
this could cause malfunctions.
Low fuel level
Filling
A label affixed to the inside of the flap
reminds you of the type of fuel to be
used according to your engine.
Operating fault
A fuel gauge malfunction is indicated by
the return of the fuel level indicator nee-
dle to zero.
Contact a PEUGEOT dealer.
When the fuel tank minimum
level is reached, this warning
light comes on on the instru-
ment panel, accompanied by
an audible signal and a message on the
multifunction display.
You have enough fuel left to drive
approximately 30 miles (50 km).
If you run out of fuel, refer to the "Practi-
cal information» section also.
77
LIGHTING CONTROLS
System for selection and control of the
various front and rear lights providing
the vehicle’s lighting.
Main lighting
The various front and rear lights of the
vehicle are designed to adapt the driv-
er’s visibility progressively in relation to
the climatic conditions:
- side lights, to be seen,
- dipped headlamps to see without daz-
zling other drivers,
- main beam headlamps to see clearly
when the road is clear,
- directional headlamps for improved
visibility when cornering.
Additional lighting
Other lights are installed to fulfil the re-
quirements of particular driving condi-
tions:
- rear fog lamps to be seen from a dis-
tance,
- front fog lamps for even better visibil-
ity,
- daytime lights to be seen during the
day.
Programming
Various automatic lighting control
modes are also available according to
the following options:
- follow-me-home lighting,
- automatic lighting,
- directional lighting.
Model without AUTO lighting
Model with AUTO lighting
automatic switching on of
the lights,
Manual controls
The lighting commands are issued di-
rectly by the driver by means of the ring
A and the lever B.
A. main lighting mode selection ring,
with:
lights off,
side lights only,
B. lever for inversion of the lights by
pulling: dipped headlamps/main
beam headlamps.
In the lights off and side lights modes,
the driver can switch on the main beam
headlamps directly ("headlamp flash")
for as long as he pulls the lever.
dipped headlamps or main
beam headlamps.
Displays
Lighting of the corresponding indicator
light on the instrument panel confirms
the selective switching on of the lighting
selected.
!
i
78
Model with rear fog lamp only
rear fog lamp
To switch on the fog lamp, turn the
ring
C forwards.
When the lights are switched off auto-
matically (with AUTO model), the fog
lamp and the dipped headlamps will re-
main on.
To switch off all of the lights, turn the
ring
C rearwards.
Model with front and rear fog lamps
front and rear fog lamps
To switch on the fog lamps, turn the
ring
C forwards.
To switch off the rear fog lamp, turn
the ring
C rearwards twice in succes-
sion.
When the lights are switched off auto-
matically (with AUTO model) or when
the dipped headlamps are switched off
manually, the fog lamps and the side
lights will remain on.
Turn the ring rearwards to switch
off the fog lamps, the side lights will
then switch off.
C. fog lamps selection ring.
The fog lamps operate with the dipped
and main beam headlamps.
i
i
79
Follow-me-home lighting
The temporary maintaining of the
dipped headlamps lighting after the ve-
hicle’s ignition has been switched off
makes the driver’s exit easier when the
light is poor.
Switching on
With the ignition off, "flash" the head-
lamps using the lever
B.
A second "headlamp flash" switches
the function off again.
Switching off
The follow-me-home lighting switches
off automatically after a set time.
Daytime lights
On vehicles fitted with daytime lights,
the corresponding lights comes on
when the vehicle is started*.
* According to country.
The instruments and controls (instru-
ment panel, multifunction display, air
conditioning control panel, ...) are not
lit, except on switching to the automatic
switching on of the lights mode or when
the lights are switched on manually.
Exterior welcome lighting
The remote switching on of the lights
makes your approach to the vehicle
easier in poor light when in automatic
switching on of the lights mode.
Switching on
Press the open padlock on the re-
mote control.
The dipped headlamps and the side
lights come on; your vehicle is also
unlocked.
Switching off
The exterior welcome lighting switches
off automatically after a set time, when
the ignition is switched on or on locking
the vehicle.
Programming
The function is activated or
deactivated via the multi-
function display configura-
tion menu.
Programming
The duration of maintaining
of the lighting is selected
via the multifunction dis-
play configuration menu.
In countries in which this function is im-
posed by regulations*, it is activated by
default.
The side lights and the number plate
lights are also switched on.
!
i
80
Coupling with the "Follow-me-
home" lighting
Association with the automatic lighting
provides the "follow-me-home" lighting
with the following additional options:
- selection of the duration of maintaining
of the lighting for 15, 30 or 60 seconds
in the vehicle parameters on the multi-
function display configuration menu,
- automatic activation of "follow-me-
home" lighting when automatic light-
ing is in operation.
Automatic lighting
The side lights and dipped headlamps
are switched on automatically, without
any action on the part of the driver,
when a low level of external light is de-
tected or in certain cases of activation
of the windscreen wipers.
As soon as the brightness returns to a
sufficient level or after the windscreen
wipers are switched off, the lights are
switched off automatically.
Activation
Turn ring
A to the "AUTO" position.
The automatic lighting is accompa-
nied by a message on the multifunc-
tion display.
Deactivation
Turn ring
A to a position other than
"AUTO". Deactivation is accompa-
nied by a message on the multifunc-
tion display.
Operating fault
In the event of a malfunction
of the brightness sensor, the li-
ghts come on, this warning light
is displayed on the instrument
panel and/or a message appears on the
multifunction display, accompanied by
an audible signal.
In this case, contact a PEUGEOT dealer.
MANUAL HEADLAMP
ADJUSTMENT
To avoid causing a nuisance to other
road users, the height of the halogen
headlamps should be adjusted in rela-
tion to the load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
2. 5 people + maximum authorised
load.
3. Driver + maximum authorised load.
i
i
79
Follow-me-home lighting
The temporary maintaining of the
dipped headlamps lighting after the ve-
hicle’s ignition has been switched off
makes the driver’s exit easier when the
light is poor.
Switching on
With the ignition off, "flash" the head-
lamps using the lever
B.
A second "headlamp flash" switches
the function off again.
Switching off
The follow-me-home lighting switches
off automatically after a set time.
Daytime lights
On vehicles fitted with daytime lights,
the corresponding lights comes on
when the vehicle is started*.
* According to country.
The instruments and controls (instru-
ment panel, multifunction display, air
conditioning control panel, ...) are not
lit, except on switching to the automatic
switching on of the lights mode or when
the lights are switched on manually.
Exterior welcome lighting
The remote switching on of the lights
makes your approach to the vehicle
easier in poor light when in automatic
switching on of the lights mode.
Switching on
Press the open padlock on the re-
mote control.
The dipped headlamps and the side
lights come on; your vehicle is also
unlocked.
Switching off
The exterior welcome lighting switches
off automatically after a set time, when
the ignition is switched on or on locking
the vehicle.
Programming
The function is activated or
deactivated via the multi-
function display configura-
tion menu.
Programming
The duration of maintaining
of the lighting is selected
via the multifunction dis-
play configuration menu.
In countries in which this function is im-
posed by regulations*, it is activated by
default.
The side lights and the number plate
lights are also switched on.
!
i
80
Coupling with the "Follow-me-
home" lighting
Association with the automatic lighting
provides the "follow-me-home" lighting
with the following additional options:
- selection of the duration of maintaining
of the lighting for 15, 30 or 60 seconds
in the vehicle parameters on the multi-
function display configuration menu,
- automatic activation of "follow-me-
home" lighting when automatic light-
ing is in operation.
Automatic lighting
The side lights and dipped headlamps
are switched on automatically, without
any action on the part of the driver,
when a low level of external light is de-
tected or in certain cases of activation
of the windscreen wipers.
As soon as the brightness returns to a
sufficient level or after the windscreen
wipers are switched off, the lights are
switched off automatically.
Activation
Turn ring
A to the "AUTO" position.
The automatic lighting is accompa-
nied by a message on the multifunc-
tion display.
Deactivation
Turn ring
A to a position other than
"AUTO". Deactivation is accompa-
nied by a message on the multifunc-
tion display.
Operating fault
In the event of a malfunction
of the brightness sensor, the li-
ghts come on, this warning light
is displayed on the instrument
panel and/or a message appears on the
multifunction display, accompanied by
an audible signal.
In this case, contact a PEUGEOT dealer.
MANUAL HEADLAMP
ADJUSTMENT
To avoid causing a nuisance to other
road users, the height of the halogen
headlamps should be adjusted in rela-
tion to the load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
2. 5 people + maximum authorised
load.
3. Driver + maximum authorised load.
!
i
80
Coupling with the "Follow-me-
home" lighting
Association with the automatic lighting
provides the "follow-me-home" lighting
with the following additional options:
- selection of the duration of maintaining
of the lighting for 15, 30 or 60 seconds
in the vehicle parameters on the multi-
function display configuration menu,
- automatic activation of "follow-me-
home" lighting when automatic light-
ing is in operation.
Automatic lighting
The side lights and dipped headlamps
are switched on automatically, without
any action on the part of the driver,
when a low level of external light is de-
tected or in certain cases of activation
of the windscreen wipers.
As soon as the brightness returns to a
sufficient level or after the windscreen
wipers are switched off, the lights are
switched off automatically.
Activation
Turn ring
A to the "AUTO" position.
The automatic lighting is accompa-
nied by a message on the multifunc-
tion display.
Deactivation
Turn ring
A to a position other than
"AUTO". Deactivation is accompa-
nied by a message on the multifunc-
tion display.
Operating fault
In the event of a malfunction
of the brightness sensor, the li-
ghts come on, this warning light
is displayed on the instrument
panel and/or a message appears on the
multifunction display, accompanied by
an audible signal.
In this case, contact a PEUGEOT dealer.
MANUAL HEADLAMP
ADJUSTMENT
To avoid causing a nuisance to other
road users, the height of the halogen
headlamps should be adjusted in rela-
tion to the load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
2. 5 people + maximum authorised
load.
3. Driver + maximum authorised load.
!
i
81
DIRECTIONAL LIGHTING
When the dipped or main beam head-
lamps are on, this function enables the
light beam to follow the direction of the
road.
The use of this function, coupled with
the xenon headlamps only, considera-
bly improves the quality of your lighting
when cornering.
with directional lighting
without directional lighting
Programming
Operating fault
The function is activated or
deactivated via the multi-
function display configura-
tion menu.
If a malfunction occurs, this
warning light flashes on the in-
strument panel, accompanied
by a message on the multifunc-
tion display.
Contact a PEUGEOT dealer.
AUTOMATIC ADJUSTMENT
OF THE DIRECTIONAL
HEADLAMPS
In order to avoid causing a nuisance to
other road users, this system corrects
the height of the xenon headlamps beam
automatically and when stationary, in re-
lation to the load in the vehicle.
If a malfunction occurs, this
warning light and/or the service
warning light is displayed on the
instrument panel, accompanied
by an audible signal and a message on
the multifunction display.
The system then places your head-
lamps inb the lowest position.
!
i
81
DIRECTIONAL LIGHTING
When the dipped or main beam head-
lamps are on, this function enables the
light beam to follow the direction of the
road.
The use of this function, coupled with
the xenon headlamps only, considera-
bly improves the quality of your lighting
when cornering.
with directional lighting
without directional lighting
Programming
Operating fault
The function is activated or
deactivated via the multi-
function display configura-
tion menu.
If a malfunction occurs, this
warning light flashes on the in-
strument panel, accompanied
by a message on the multifunc-
tion display.
Contact a PEUGEOT dealer.
AUTOMATIC ADJUSTMENT
OF THE DIRECTIONAL
HEADLAMPS
In order to avoid causing a nuisance to
other road users, this system corrects
the height of the xenon headlamps beam
automatically and when stationary, in re-
lation to the load in the vehicle.
If a malfunction occurs, this
warning light and/or the service
warning light is displayed on the
instrument panel, accompanied
by an audible signal and a message on
the multifunction display.
The system then places your head-
lamps inb the lowest position.
82
WIPER CONTROLS
System for selection and control of the
various front and rear wiping modes for
the elimination of rain and cleaning.
The vehicle’s various front and rear wip-
ers are designed to improve the driver’s
visibility progressively in relation to the
climatic conditions.
Manual controls
The wiper commands are issued direct-
ly by the driver by means of the lever
A
and the ring
B.
Model with intermittent wiping
Model with AUTO wiping
fast (heavy rain),
normal (moderate rain),
intermittent (proportional to
the speed of the vehicle),
automatic, then single
wipe (see following
page).
park,
single wipe (press down-
wards),
Programming
Various automatic wiper control modes
are also available according to the fol-
lowing options:
- automatic wiping for the windscreen
wipers,
- rear wiping on engaging reverse
gear.
Windscreen wipers
A. wiping speed selection lever:
or
!
83
Windscreen and headlamp wash
B. rear wiper selection ring:
park,
intermittent wipe,
wash-wipe (set duration).
Reverse gear
When reverse gear is engaged, the
rear wiper will come into operation if the
windscreen wipers are operating.
Programming
Pull the windscreen wiper stalk to-
wards you. The windscreen wash
then the windscreen wipers operate
for a fixed period.
If the dipped headlamps are on, the
headlamp washers operate at the same
time.
Rear wiper
The function is activated or
deactivated via the multi-
function display configura-
tion menu.
This function is activated
by default.
Screenwash/headlamp
wash low
In the case of vehicles fitted with
headlamp washers, when the
minimum level of the reservoir is
reached, this warning light and/or
the service warning light is displayed on
the instrument panel, accompanied by an
audible signal and a message on the mul-
tifunction display.
Next time you stop, fill the screenwash/
headlamp wash reservoir.
The warning light is displayed when the ig-
nition is switched on, or every time the stalk
is operated, until the reservoir is filled.
!
i
i
84
Special position of the
windscreen wipers
Automatic windscreen wiping
The windscreen wipers operate auto-
matically, without any action on the part
of the driver, if rain is detected (sensor
behind the interior mirror), adapting their
speed to the intensity of the rainfall.
Activation
This is controlled manually by the dri-
ver by pushing lever
A to the "AUTO"
position.
It is accompanied by a message on the
multifunction display.
In the minute following switching off of
the ignition, any action on the stalk po-
sitions the wipers in the centre of the
windscreen.
This action enables you to position the
wiper blades for winter parking, clean-
ing or replacement.
To park the wipers after this has been
done, switch on the ignition and operate
the stalk.
Switching off
This is controlled manually by the driver
by moving lever
A upwards and return-
ing it to position
"0".
It is accompanied by a message on the
multifunction display.
Operating fault
If an automatic wiping malfunction oc-
curs, the wipers will operate in intermit-
tent mode.
Contact a PEUGEOT dealer to have the
system checked.
!
i
i
84
Special position of the
windscreen wipers
Automatic windscreen wiping
The windscreen wipers operate auto-
matically, without any action on the part
of the driver, if rain is detected (sensor
behind the interior mirror), adapting their
speed to the intensity of the rainfall.
Activation
This is controlled manually by the dri-
ver by pushing lever
A to the "AUTO"
position.
It is accompanied by a message on the
multifunction display.
In the minute following switching off of
the ignition, any action on the stalk po-
sitions the wipers in the centre of the
windscreen.
This action enables you to position the
wiper blades for winter parking, clean-
ing or replacement.
To park the wipers after this has been
done, switch on the ignition and operate
the stalk.
Switching off
This is controlled manually by the driver
by moving lever
A upwards and return-
ing it to position
"0".
It is accompanied by a message on the
multifunction display.
Operating fault
If an automatic wiping malfunction oc-
curs, the wipers will operate in intermit-
tent mode.
Contact a PEUGEOT dealer to have the
system checked.
i
i
!
85
COURTESY LIGHTS
Selection and control of the various
passenger compartment lights.
1. Front courtesy light
2. Map reading lights
3. Rear side reading lights
4. Rear courtesy light
Front and rear courtesy lights
In this position, the courtesy li-
ght comes on gradually:
Map reading lights
With the ignition on, press the cor-
responding switch.
- when the vehicle is unlocked,
- when the key is removed from the ig-
nition,
- when a door is opened,
- when the remote control locking button is
activated, in order to locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
Permanently off.
Permanent lighting.
Rear side reading lights
With the ignition on, the first press of
the corresponding switch switches
on the reading light concerned in
permanent lighting mode.
Following a second press, it comes on:
- when the vehicle is unlocked,
- when the key is removed from the
ignition,
- when a door is opened,
- when the remote control locking
button is pressed, in order to locate
your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is
closed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст