Peugeot 5008 (2023 year). Manual in english — page 3
Ease of use and comfort
When driving
Manually-adjusted seats
5. Lumbar support adjustment
3
Maintain a good driving position and hold the
(only on the driver's seat)
steering wheel with both hands at the 'quarter to
► Turn the knob forwards or backwards
three' position, so that you can easily and quickly
to increase or decrease the level of lumbar
reach the controls behind and near the steering
support.
wheel.
‘AGR’ certified seats
Never adjust the seats or steering wheel
when driving.
Additional adjustments
Always keep your feet on the floor.
Front seats
Before moving the seat backwards,
ensure that there is no person or object
1.
Longitudinal adjustment of the seat position
that might prevent the full travel of the seat.
► Raise the control bar and slide the seat
1.
Seat cushion length adjustment
There is a risk of trapping or pinching
forwards or backwards.
► Pull the handle forwards to release the
passengers if present in the rear seats or of
► Release the bar to lock the seat in
cushion, then move the front part of the seat
jamming the seat if large objects are placed
position in one of the notches.
cushion forwards or backwards.
on the floor behind the seat.
2.
Seat cushion height adjustment
2.
Seat cushion angle electric adjustment
► Raise or lower the control as many times
► Press and hold the front or rear of the
as needed to obtain the desired height.
button to raise or lower the front part of the
3.
Seat backrest angle adjustment
seat cushion.
► Turn the knob forwards or backwards to
recline the backrest to the desired angle.
or
► For a passenger seat that can be placed
in the table position, pull the handle and
guide the backrest forwards or backwards.
4.
Head restraint height adjustment
Refer to the corresponding section.
43
Ease of use and comfort
3. Lumbar support electric adjustment
Folding the backrest
Front head restraints
The control allows independent adjustment of
the depth and vertical position of the lumbar
Adjusting the height
support.
► Press and hold the front or rear of the
control to increase or reduce the lumbar
support.
► Press and hold the top or bottom of the
control to raise or lower the lumbar support
area.
Placing the passenger seat
► Pull the control fully upwards to release the
in the table position
backrest.
The backrest of the passenger seat can be fully
► Tip the backrest fully forwards.
Upwards:
folded forwards and secured in this position.
► Pull the head restraint up to the desired
This function, when associated with folding
In this position, the backrest can support
position; you can feel the head restraint clicking
of the backrest of the rear seats, helps with
a maximum load of 30 kg.
into position.
transporting long and bulky objects.
When sharp deceleration occurs, objects
Downwards:
First steps:
placed on the folded backrest can turn into
► Press lug A to lower the head restraint.
► Lower the head restraint.
projectiles.
► Fold up the “aircraft” type table (depending
The head restraint is correctly adjusted
on version).
when its upper edge is level with the top
Returning the backrest into position
► Move the seat backwards to allow space for
of the head.
► Pull the control fully upwards to release the
the head restraint.
backrest.
► Adjust the seat to the lowest position.
► Raise the backrest and guide it backwards
Removing a head restraint
► Check that there is nothing that might
until it latches into place.
► Pull the head restraint fully up.
interfere with folding of the backrest (seat belt,
► Check that the backrest is correctly latched
► Press lug A to release the head restraint and
child seat, items of clothing, bags, etc.).
into place.
raise it fully.
Deactivation of the front passenger
► Stow the head restraint securely.
airbag is recommended.
44
Ease of use and comfort
Refitting a head restraint
5. Lumbar support adjustment
3
► Insert the head restraint rods into the guides
The control allows independent adjustment of
in the corresponding seat backrest.
the depth and vertical position of the lumbar
► Push the head restraint fully down.
support.
► Press the lug A to release the head restraint
► Press and hold the front or rear of the
and push it down.
control to increase or reduce the lumbar
► Adjust the height of the head restraint.
support.
► Press and hold the top or bottom of the
Never drive with the head restraints
control to raise or lower the lumbar support
removed; they should be in place and
area.
adjusted for the occupant of the seat.
Memorising driving
Electrically-adjusted driver's
positions
seat
1.
Seat cushion height and angle adjustment/
Associated with the electrically-adjusted driver’s
Longitudinal adjustment of the seat position
seat, this function allows two driving positions
To carry out these electric adjustments,
► Raise or lower the front of the control to
to be memorised, to make these adjustments
switch on the ignition or start the engine
obtain the desired seat cushion angle.
easier if there are frequent driver changes.
if the vehicle has gone into energy economy
► Raise or lower the rear of the control to
It records the electric adjustments made to the
mode.
raise or lower the seat cushion.
seat and door mirrors.
These electric adjustments are accessible
► Slide the control forwards or backwards to
about 1 minute after opening the driver's door.
move the seat forwards or backwards.
They are deactivated about 1 minute after
2.
Seat backrest angle adjustment
switching the ignition off.
► Turn the control forwards or backwards to
recline the backrest to the desired angle.
3.
Head restraint height adjustment
Refer to the corresponding section.
4.
Seat cushion length adjustment
► Pull the handle forwards to release the
cushion, then move the front part of the seat
cushion forwards or backwards.
Using buttons M/1/2
45
Ease of use and comfort
► Enter the vehicle and switch the ignition on.
Heated seats
Prolonged use of heated seats is not
► Adjust your seat and the door mirrors.
recommended for people with sensitive
► Press button M, then press button 1 or 2
skin.
within 4 seconds.
There is a risk of burns for people whose
An audible signal confirms the memorisation.
perception of heat is impaired (e.g. illness,
Memorising a new position cancels the previous
taking medication).
position.
To keep the heated pad intact and to prevent
a short circuit:
Recalling a stored position
- Do not place heavy or sharp objects on the
seat.
While the seat is moving, take care that
The function is active only with the engine
- Do not kneel or stand on the seat.
no person or object hinders the
running and when the outside temperature is
- Do not spill liquids onto the seat.
automatic movement of the seat.
below 20°C.
- Never use the heating function if the seat
With the ignition on or engine running
► Press the button corresponding to the seat.
is damp.
► Press button 1 or 2 to recall the
► Each press changes the heating level; the
corresponding position.
corresponding number of indicator lamps come
Multipoint massage
An audible signal sounds when adjustment is
on.
System with a choice of type of massage and
complete.
► To switch off the heating, press the button
adjustment of its intensity.
You can interrupt the current movement by
until all of the indicator lamps are off.
This system operates with the engine running, as
pressing button M, 1 or 2 or by using one of the
The system status is memorised when the
well as in STOP mode of the Stop & Start.
seat adjustment controls.
ignition is switched off.
The massage settings are adjusted via the touch
A stored position cannot be recalled while
Do not use the function when the seat
screen.
driving.
is not occupied.
From the front seat:
The recalling of stored positions is deactivated
Reduce the heating intensity as soon as
► Press this button; its green indicator
45 seconds after switching off the ignition.
possible.
lamp comes on.
When the seat and passenger compartment
The settings page is displayed on the touch
have reached a satisfactory temperature,
screen with the last memorised settings.
switch the function off; reducing electrical
If the settings suit you and you make no
consumption in turn decreases energy
changes, the display returns to its previous state,
consumption.
and the function activates immediately.
Seats must be adjusted one after another,
starting with the driver's seat.
46
Ease of use and comfort
To modify the settings:
► Adjust the height and reach to suit your
As a safety measure, the mirrors should
3
► Begin with the driver’s seat.
driving position.
be adjusted to reduce the "blind spots".
► Select a massage intensity from the three
► Push the control to lock the steering wheel.
The objects that you see in the mirrors are
levels offered: "1" (Low), "2" (Normal) or "3"
in fact closer than they appear. Take this
For safety reasons, these adjustments
(High).
into account in order to correctly judge the
must only be carried out with the vehicle
► Select another type of massage from those
distance of vehicles approaching from behind.
stationary.
offered.
► Wait for the driver's seat settings page to
Manual folding
disappear.
Mirrors
The mirrors can be folded manually (parking
► Next, proceed with the passenger's seat in
obstruction, narrow garage, etc.).
the same way.
► Turn the mirror towards the vehicle.
The changes are applied immediately.
Door mirrors
Once activated, the system starts a one hour
Electric folding
massage cycle, made up of sequences of 6
Adjustment
Depending on equipment, the door mirrors can
minutes of massage followed by 3 minutes at
be folded electrically.
rest.
The system automatically stops at the end of the
► From the inside, with the
cycle; the indicator lamp for the button goes off.
ignition on, place control A in the
central position.
► Pull control A backwards.
Steering wheel
► Lock the vehicle from the outside.
adjustment
If the mirrors are folded using control A,
they will not unfold when the vehicle is
unlocked.
► Move control A to the right or to the left to
select the corresponding mirror.
Electric unfolding
► Move control B in any of the four directions
► From outside: unlock the vehicle.
to adjust.
► From inside: with the ignition on, place
► When stationary, pull the control to release
► Return control A to its central position.
control A in the central position and then pull it
the steering wheel.
rearwards.
47
Ease of use and comfort
Depending on version, the automatic
Interior rear view mirror
Rear head restraints
door mirror folding/unfolding function is
configured via the Driving / Vehicle touch
screen menu.
Otherwise, this setting can be carried out at a
PEUGEOT dealer or a qualified workshop.
Automatic tilting in reverse gear
Depending on version, this function allows to
automatically tilt the mirrors downwards to assist
with parking manoeuvres in reverse gear.
With the engine running, on engaging reverse
gear, the mirror glasses tilt downwards.
They return to their initial position:
- A few seconds after coming out of reverse
The electrochrome system uses a sensor that
gear.
detects the level of exterior brightness and that
- Once the vehicle speed exceeds 6 mph
coming from the rear of the vehicle, in order to
(10 km/h).
automatically and gradually switch between day
- When the engine is switched off.
and night usage.
This function is set via the Driving/
To ensure optimum visibility while
Vehicle touch screen menu.
manoeuvring, the mirror automatically
brightens when reverse gear is engaged.
Demisting/Defrosting
The system is deactivated if the load in the
The demisting/defrosting of the door
boot exceeds the height of the load space
mirrors works with the demisting/
cover or if the load space cover has items
defrosting of the rear screen.
placed on it.
For more information on Rear screen
High position (use):
demisting/defrosting, refer to the
► Pull the head restraint fully up.
corresponding section.
Low position (stowing; when the seats are not
in use):
► Press the lugs A to release the head restraint
and push it down.
48
Ease of use and comfort
The rear head restraints can be removed.
Folding the backrests
► Check that the centre seat belt buckle is
3
Removing a head restraint
stored in its housing.
► Pull the head restraint fully up.
The folding of the backrest is
► Press the lugs A to release the head restraint
accompanied by a slight lowering of the
and remove it completely.
corresponding cushion.
► Store the head restraint.
To obtain a flat surface, it is necessary to
place the adjustable boot floor in the high
Refitting a head restraint
position.
► Insert the head restraint rods into the guides
When the backrest is released, the red
in the corresponding seat backrest.
indicator in the release grip is visible.
► Push the head restraint down as far as it will
go.
► Press the lugs A to release the head restraint
Folding from the passenger
and push it down.
Each section of the backrest has two release
compartment
controls:
Never drive with passengers seated at
- A grip 1 on the outer edge of the backrest.
the rear when the head restraints are
- A lever 2 on the boot side trim (depending on
removed; the head restraints should be in
version).
place and in the high position.
The backrests should only be
The head restraint for the central
manoeuvred when the vehicle is
seat and those for the side seats
stationary.
are not interchangeable.
First steps:
► Lower the head restraints.
► Lift up the rear armrest.
Rear bench seat
► If necessary, move the front seats forward.
► Press the backrest release grip 1.
► Check that no person or object might interfere
► Guide the backrest 3 down to the horizontal
with the folding of the backrests (e.g. clothing,
position.
luggage).
► Check that the outer seat belts are lying flat
Bench seat with fixed cushions and split folding
on the backrests.
backrests (2/3-1/3) to adapt the boot load space.
49
Ease of use and comfort
Folding from the boot
► Put the backrest 3 in the upright position and
push it firmly to latch it home.
► Check that the red indicator is no longer
visible in the release grip 1.
► Ensure that the outer seat belts were not
trapped during the operation.
Please note: an incorrectly latched
backrest compromises the safety of
passengers in the event of sudden braking or
an accident.
The contents of the boot may be thrown
forward - risk of serious injury!
► Pull the backrest release lever 2 towards you.
The backrest 3 folds fully onto the cushion.
Second row seats
Repositioning the backrests
First check that the outer seat belts are
A. Longitudinal adjustment
lying vertically flat alongside the backrest
B. Seat backrest angle adjustment and folding
latching rings.
Seat adjustment
C. Folding the backrest from behind and
emergency exit for third row passengers
The three second row seats are independent
D. Access to third row seats
and of the same width. Their backrests can be
folded to adapt the boot load space.
50
Ease of use and comfort
Longitudinal adjustment
► Lift control handle B1 and guide the backrest
Before and while performing the
3
backwards or forwards, raising yourself slightly
operation on the seats, check that the
if needed.
passengers, children in particular, keep their
► Release the handle and ensure the backrest
hands and their feet far from the moving parts
is properly locked on one of the positions offered.
of the seats (hinges, slides, etc.) - risk of
Central seat
serious injury!
► Lift control strap B2 and guide the backrest
backwards or forwards, raising yourself slightly
Folding from the outside
if needed.
► Release the strap and ensure the backrest is
properly locked on one of the positions offered.
Flat floor
► Raise control bar A and slide the seat
forwards or backwards.
► Release the bar to lock the seat in position in
one of the notches.
Seat backrest angle adjustment
► Pull handle B1 or strap B2 until the backrest
is fully folded.
► Release the control.
► Gently push the backrest forwards so that
the backrest tilts until it is folded onto the seat
cushion.
Folding the backrests
► Check that the "aircraft" type tables of the
front seats are properly folded.
► Place the second row seats in the maximum
rear position.
Side seats
51
Ease of use and comfort
Folding from the boot
► Straighten the backrest until it locks.
Before unfolding the continuity panels,
check that the 2nd row seats are pulled as
Before performing any operations on the
far back as possible.
rear seats, to avoid damage to the seat
belts, check that the outer seat belts are
properly tensioned. The central seat belt must
Accessing third row seats
be stored in the headlining.
The third row seats are accessed via the second
row side seats.
Continuity panels
When loading, for example, or from the third row
seats:
► Pull strap C to unlock the desired seat and
give the backrest a slight push forwards.
Repositioning the seat
From the outside or from the third row seats:
► Check that the "aircraft" type tables of the
Each seat has a continuity panel at the bottom of
front seats are properly folded up.
the backrest, which, once unfolded:
► Pull paddle D and guide the backrest
- allows for a continuous loading surface in the
forwards to tilt it and move the seat forwards.
boot, whatever the position of the seats,
To put the seat back in place:
- prevents objects from sliding beneath the 2nd
► Straighten the backrest until the seat locks.
row seats.
Whatever the initial position of the seat, it is
The continuity panels are held against the
placed automatically a third of the way along
backrests with a magnetic fixing element.
the longitudinal adjustment range in order to
These continuity panels are not designed
preserve enough space for passengers in the
to support a weight greater than 30 kg.
third row seats.
► Place the continuity panels of the 2nd row
seats back up against the backrests.
52
Ease of use and comfort
If this system fails (paddle D), the third
► Pull one of the straps; the 3 sections of the
3
row passengers can also get out after
corresponding panel fold into concertina form.
having folded the backrest of the second row
When the 3rd row seats are straightened, these
seats using strap C.
folded concertina panels can be left upright or
Do not let children operate the seats
flat behind the seats (freeing up the seat well as
unsupervised.
a storage space).
Positioning the seats
Third row seats
These operations are carried out from the boot
When there is a seat at the back of the boot, the
sill.
removable support is fixed against the front wall
of its housing.
If the seat is removed from the back of the boot
The two third row seats are stored in a retracted
for extra storage space, the removable support
position in the bottom of the boot. Each one is
must be installed on the two lugs on the central
covered with rigid concertina panels, secured to
wall.
the vehicle.
Folding the concertina
Do not let children operate the seats
unsupervised.
panels
Each concertina panel can support a
maximum load of 100 kg with the third
► Remove the load space cover roller.
row seats folded away.
► Straighten the continuity panels of the 2nd row
With the third row seats removed and the
seats.
removable concertina panels supports
► Fold back the concertina panel and straighten
installed, the maximum load is limited to
it vertically.
50 kg.
► Pull the black strap E, located behind the
backrest.
The backrest tilts backwards bringing the seat
cushion with it; the seat locks in the open
position.
53
Ease of use and comfort
The load space cover roller can be stored behind
► Reposition the concertina panels above the
the backrests of the 3rd row seats.
retracted seats.
For more information on the Boot fittings, and
Before doing anything to the 3rd row
in particular the load space cover roller, refer to
seats, straighten the continuity panels of
the corresponding section.
the 2nd row seats.
Do not try to fold back a seat in the 3rd row
Storing the seats
without having opened it until the backrest is
fully locked.
Do not leave anything on or underneath the
► Lift the yellow lever G, located on the right-
cushions of the 3rd row seats when they are
hand side, as far upwards as possible to unlock
being folded.
the seat.
Do not guide strap F when storing the seat -
your fingers may get trapped!
Removing the seats
Removing the right-hand seat first is
recommended in order to facilitate access to the
left-hand seat unlocking control.
► Straighten the continuity panels of the 2nd row
seats.
► Place the head restraints in the low position.
► Check that the seat belts in the 3rd row are
► While keeping the yellow lever held up as far
properly stored along the side trims without
as possible, raise the rear part of the seat using
being folded or twisted.
the red strap F.
► Pull red strap F, located at the bottom of the
backrest.
The seat is unlocked.
► Push the backrest slightly forwards.
The seat must be in the folded-away position.
The backrest tilts and folds onto the cushion; the
These operations must be performed from the
folded seat is stored at the back of its storage
boot sill.
area.
► Fold back the concertina panel.
54
Ease of use and comfort
► While holding it by the sides at the plastic
Seat modularity
3
covers, tilt the seat forwards.
► Simultaneously place both hooks located at
the front of the seat onto the coloured securing
lugs on the right and left at the bottom of the seat
well.
Configuration examples
Check that the front hooks of the seat are
positioned correctly on the two lugs.
► Once the rear part of the seat has been
If they are not, you must remove the seat and
raised, take hold of each side of the seat
start the procedure again.
cushion, at the plastic covers, then bring the seat
towards you, keeping it at the same angle.
Repositioning the seats
These operations must be performed from the
boot sill.
7 seats
5 seats
Transport of
As long as the seat is not in the correct
objects
position, it must be held with both hands
by the sides, keeping it folded.
► Release the rear part of the seat which will
► Check in advance that the seat storage well
lock in place under its own weight.
is empty and that the removable support is
The yellow lever G folds back automatically.
properly secured against the front wall.
If the seat is not perfectly horizontal, do
not press on the backrest and do not try
to unfold it - risk of damaging the mechanism!
Take out the seat and start the operation
again.
6 seats
4 seats
By folding the second row seats and
retracting the third row seats, you obtain
55
Ease of use and comfort
a continuous storage floor through to the back
Air distribution
regulate the automatic air conditioning
of the front seats.
system.
By placing the front passenger seat in the
► Operate the air conditioning system for at
table position, you obtain a continuous
least 5 to 10 minutes once or twice a month to
storage floor through to the dashboard.
keep it in good working order.
► If the system does not produce cold air,
Operations on the seats must only be
switch it off and contact a PEUGEOT dealer
done when the vehicle is stationary.
or a qualified workshop.
When towing a large load on a steep gradient
in high temperatures, switching off the air
conditioning increases the available engine
Heating and Ventilation
power, enhancing the towing capacity.
1.
Windscreen demisting/de-icing vents
Air intake
2.
Front side window demisting/de-icing vents
The air circulating in the passenger compartment
Avoid driving for too long with the
3.
Adjustable and closable side air vents
is filtered and originates either from the
ventilation off or with prolonged operation
4.
Adjustable and closable central air vents
exterior, via the grille located at the base of the
of interior air recirculation. Risk of misting and
5.
Air outlets to the front footwells
windscreen, or from the inside in air recirculation
deterioration of the air quality!
6.
Air outlets to the rear footwells
mode.
7.
Adjustable and closable air vents, with blower
Controls
(depending on version)
If the interior temperature is very high
after the vehicle has stood for a long
Depending on version, the controls are
time in the sunshine, air the passenger
accessible in the Climate touch screen menu
Advice
compartment for a few moments.
or are grouped together on the centre console
Using the ventilation and air
Put the air flow control at a setting high
panel.
conditioning system
enough to quickly change the air in the
► To ensure that air is distributed evenly,
passenger compartment.
keep the external air intake grilles at the base
of the windscreen, the nozzles, the vents, the
Condensation created by the air
air outlets and the air extractor in the boot
conditioning results in a discharge of
free from obstructions.
water underneath the vehicle. This is perfectly
► Do not cover the sunshine sensor located
normal.
on the dashboard; this sensor is used to
56
Ease of use and comfort
Servicing the ventilation and air
Dual-zone automatic air
3
conditioning system
► Ensure that the passenger compartment
conditioning
filter is in good condition and have the filter
This system automatically controls the activation
elements replaced regularly.
of the air conditioning system, regulating the
We recommend using a composite passenger
temperature, air flow and air distribution inside
compartment filter. Its specific active additive
the passenger compartment.
helps protect against polluting gases and bad
This system works with the engine running, but
smells.
access to the ventilation and its controls remains
► To ensure correct operation of the
possible with the ignition on.
air conditioning system, have it checked
Press the Climate menu button to display
according to the recommendations in the
the system controls page.
Manufacturer’s service schedule.
Stop & Start
The heating and air conditioning systems
1.
Temperature adjustment
only operate when the engine is running.
2.
Air flow adjustment
Temporarily deactivate the Stop & Start
3.
Air distribution adjustment
system to maintain a comfortable temperature
4.
Interior air recirculation
in the passenger compartment.
5.
Air conditioning on/off
For more information on the Stop &
6.
Maximum air conditioning
Start system, refer to the corresponding
7.
Switching the system off
section.
8.
Automatic visibility programme
9.
Automatic comfort programme on/off
Rechargeable hybrid vehicles
10.
Access to the secondary page
Intensive use of the air conditioning
11.
Selection of settings for the Automatic
reduces the vehicle range in Electric mode.
comfort programme (Soft/Normal/Fast)
12.
"AQS (Air Quality System)" function (with
pollution sensor) (depending on version)
13.
Mono-zone/Dual-zone
57
Ease of use and comfort
14. Temperature conditioning (depending on
- "Normal": offers the best compromise
Automatic Visibility
version)
between a comfortable temperature and quiet
programme
"REAR" function (depending on version)
operation (default setting).
- "Fast": provides strong and effective air flow.
For more information on button 8, refer to the
To change the current setting (shown by the
“Front Demisting/Defrosting” section.
Adjusting the temperature
corresponding indicator lamp), press button 11
The driver and front passenger can each choose
"Air Quality System" (AQS)
repeatedly until the desired setting is displayed.
their own temperature setting.
To ensure passenger comfort in the rear seats,
function
The value indicated corresponds to a level of
favour "Normal" and "Fast" settings.
Using a pollution sensor, this function
comfort and not to a precise temperature.
This setting is associated with automatic mode
automatically activates recirculation of the
► Press one of the buttons 1 to increase (red)
only. However, on deactivation of AUTO mode,
interior air once a certain level of polluting
or decrease (blue) the value.
the indicator lamp for the most recently selected
substances in the exterior air is detected.
It is recommended that you avoid a difference of
setting remains on.
When the air quality returns to a satisfactory
more than 3°C in the settings for left and right.
Changing the setting does not reactivate AUTO
level, recirculation of interior air is automatically
mode if it was deactivated.
deactivated.
Automatic Comfort
In cold weather with the engine cold, the
This function is not designed to detect
programme
unpleasant odours.
air flow is increased gradually until the
This automatic mode ensures optimum
comfort setting has been reached, in order to
Recirculation is automatically activated when the
management of the passenger compartment
limit the delivery of cold air into the passenger
windscreen wash is used or when reverse gear
temperature, air flow and air distribution, based
compartment.
is engaged.
on the selected comfort level.
On entering the vehicle, if the interior
The function does not operate if the exterior
► Press button 9 to activate or deactivate the
temperature is much colder or warmer than
temperature is below 5 °C, to avoid the risk of
air conditioning system’s automatic mode .
the comfort setting requested, there is no
misting of the windscreen and side windows.
The indicator lamp in the button lights up
need to alter the value displayed to more
To activate or deactivate the function, go to the
when the air conditioning system is operating
quickly reach the required level of comfort.
secondary page by using the "OPTIONS" button,
automatically.
The system automatically corrects the
then press button 12.
You can adjust the intensity of the
temperature difference as quickly as possible.
automatic Comfort programme by using the
Manual control
"OPTIONS" button to select one of the available
It is possible to manually adjust one or more
settings:
of these functions, while the system retains
- "Soft": provides soft and quiet operation by
automatic control of the other functions:
limiting air flow.
- air flow.
58
Ease of use and comfort
- air distribution.
Air conditioning on/off
Mono-zone/Dual-zone
3
The indicator lamp in the "AUTO” button goes
The air conditioning system is designed to
The passenger temperature setting can be linked
out if a setting is changed.
operate effectively in all seasons, with the
to the driver's setting (mono-zone function).
► Press button 9 again to reactivate the
windows closed.
It is available in the secondary page which can
automatic Comfort programme.
It is used to:
be accessed via the "OPTIONS" button.
- lower the temperature in summer,
► Press button 13 to activate the "MONO"
Adjusting the air flow
- increase the effectiveness of demisting in
function; its status is displayed as "ON".
► Press one of the buttons 2 (- or +) to increase
winter, above 3°C.
The function is automatically deactivated if the
or decrease air flow.
► Press button 5 to activate/deactivate the air
passenger uses their temperature adjustment
The air flow symbol (a fan) is filled in according
conditioning system.
buttons (dual-zone function).
to the request.
When the system is activated, the indicator lamp
When the air flow is reduced to a minimum,
in the button comes on.
“REAR” function
ventilation stops.
"OFF" is displayed alongside the fan.
Air conditioning does not operate when
the air flow is disabled.
Adjusting the air distribution
To obtain cool air more quickly, enable interior
► Press the buttons 3 to adjust the air flow
air recirculation for a brief period. Then return
distribution inside the passenger compartment.
to the intake of exterior air.
Windscreen and side windows.
Switching off the air conditioning may result in
some discomfort (humidity or misting).
Central and side air vents.
Maximum air conditioning
Footwells.
This function automatically adjusts the
temperature setting to the lowest possible, the
The lighting of the button indicates that air is
air distribution towards the central and side air
being blown in the specified direction.
vents, the air flow to maximum and activates
For a uniform distribution of air in the passenger
interior air recirculation.
compartment, the three buttons can be activated
When this function is activated, the rear air
► Press button 6 to activate/deactivate the
simultaneously.
vents blower starts up. In this case, the rear
function (the indicator lamp will come on/switch
In AUTO mode, the indicator lamps in all three
passengers can control the air flow from these
off).
buttons 3 are off.
air vents independently of the air conditioning air
Once the function is deactivated, the system
flow control for the front air vents.
returns to the previous settings.
59
Ease of use and comfort
When the function is deactivated, the maximum
The temperature is no longer regulated. A slight
The programme automatically manages the air
air flow distributed by the rear air vents is limited
flow of air can still be felt, due to the forward
conditioning (depending on version), air flow
by the air conditioning air flow setting for the
movement of the vehicle.
and air intake, and provides optimum distribution
front air vents.
towards the windscreen and side windows.
The function is available on the secondary
It is possible to manually change the air flow
Interior air recirculation
page, which can be accessed by pressing the
without deactivating the automatic Visibility
“OPTIONS” button.
The intake of exterior air prevents the formation
programme.
► Press button 14 to activate the "REAR"
of mist on the windscreen and side windows.
With Stop & Start, when demisting has
function; its status is displayed as "ON".
Recirculating the interior air isolates the
been activated, STOP mode is not
► Press the “large fan” or “small fan” button to
passenger compartment from outside odours
available.
increase or decrease the air flow.
and fumes and allows the desired passenger
The corresponding indicator lamps come on.
compartment temperature to be achieved more
If all of the indicator lamps are off, a slight air
rapidly.
In wintry conditions, before moving off,
flow can still be felt as a result of the vehicle's
► Press this button to activate/deactivate
remove all snow or ice on the windscreen
movement.
the function (confirmed by the
near the camera.
illumination/extinction of the indicator lamp).
Otherwise, the operation of the equipment
Ventilation with the ignition
using the camera may be affected.
This function is activated automatically
on
when reverse gear is engaged.
When the ignition is switched on, the ventilation
Heated windscreen
system and the air flow 2 and air distribution
3 settings in the passenger compartment are
Front demisting
activated, for a period which depends on the
- defrosting
battery charge.
This function does not include the air
conditioning system.
Automatic Visibility
programme
Switching the system off
This mode allows the windscreen and side
► Press button 7; all the indicator lamps of the
windows to be demisted or defrosted as quickly
system go out.
as possible.
This action deactivates all of the functions of the
► Press this button to activate/deactivate
air conditioning system.
the mode (confirmed by the illumination/
extinction of the indicator lamp).
60
Ease of use and comfort
In cold weather, this system heats the bottom of
Depending on version, it also demists/defrosts
► Select the time of entry into the vehicle and
3
the windscreen, as well as the area alongside
the doors mirrors.
the desired days. Press OK.
the left-hand windscreen pillar.
► Press this button to activate/deactivate
► Press ON to activate this programming.
Without changing the settings for the air
the function (confirmed by the
The pre-conditioning sequence begins
conditioning system, it allows faster release
illumination/extinction of the indicator lamp).
approximately 45 minutes before the
of the windscreen wiper blades when they
Demisting/defrosting switches off automatically
programmed time when the vehicle is connected
are frozen to the windscreen and helps avoid
to prevent an excessive consumption of
(20 minutes when it is not connected) and is
the accumulation of snow resulting from the
electrical current.
maintained for 10 minutes after.
operation of the windscreen wipers.
Switch off demisting/defrosting when
you no longer need it; reducing
Switching on/off
electrical consumption in turn decreases
energy consumption.
Temperature
pre-conditioning
This indicator lamp comes on fixed when
a temperature pre-conditioning cycle is
(Rechargeable hybrid)
programmed. It flashes when temperature pre-
This function allows you to programme the
conditioning is in progress.
► With the engine running, press this button to
temperature in the passenger compartment to
activate/deactivate the function (confirmed by an
You can set multiple programmes.
reach a pre-defined, non-modifiable temperature
indicator lamp).
Each one is saved in the system.
(approx. 21°C) before you enter the vehicle, on
The function is activated when the outside
To optimise the driving range, we recommend
the days and at the times of your choice.
temperature drops below 0°C. It is deactivated
starting a programme while the vehicle is
This function is available when the vehicle is
automatically when the engine is switched off.
connected.
connected or not connected.
Programming can also be carried out
Programming
Rear screen
from a smartphone using the
(With PEUGEOT Connect Nav)
MYPEUGEOT APP application.
demisting/defrosting
In the Climate > OPTIONS menu:
With PEUGEOT Connect Radio, programming
This demisting/defrosting only works with the
Select Temperature conditioning.
can only be carried out from a smartphone using
engine running.
the application.
► Press + to add a programme.
61
Ease of use and comfort
For more information on Remote functions,
Make sure you do not leave any item in
Front fittings
refer to the corresponding section.
the passenger compartment which could
act like a magnifying glass under the effect of
The fan noise that occurs during
the sun's rays and cause a fire - risk of fire or
temperature pre-conditioning is perfectly
damage to interior surfaces!
normal.
Sun visor
Operating conditions
► With the ignition on, raise the concealing
- The function is only activated when the
flap; depending on the version, the mirror is
ignition is switched off and the vehicle
illuminated automatically.
locked.
This sun visor is also equipped with a ticket
- When the vehicle is not connected, the
holder.
function is only activated if the battery charge
level is greater than 20%.
Glove box
- When the vehicle is not connected and a
1.
Grab handle
► To open the glove box, lift the handle.
recurring programme is active (e.g. from Monday
2.
Sun visor
With the ignition on, the glove box is lit when
to Friday), if two temperature pre-conditioning
3.
Card holder
open.
sequences are run without the vehicle being
4.
Storage compartment below the steering
used, the programme will be deactivated.
wheel
5.
Illuminated glove box
6.
Door pockets
7.
USB socket / Front 12 V accessory socket
(120 W)
8.
Storage compartment or Wireless
smartphone charger
9.
Storage compartment
10.
Cup holder
11.
Front armrest with storage
12.
USB sockets or Rear 12 V socket (120 W)
13.
Storage compartment or Rear blower
62
Ease of use and comfort
It houses the front passenger airbag deactivation
Power supply and recharging.
When the USB socket is used, the
3
switch.
portable device charges automatically.
Likewise, plus exchange of multimedia
While charging, a message is displayed if the
Never drive with the glove box open
data with the audio system.
power drawn by the portable device exceeds
when a passenger is at the front. It may
Likewise, plus use of smartphone
the current supplied by the vehicle.
cause injury during sharp deceleration!
applications with the touch screen.
For more information about how to use this
equipment, refer to the sections describing
12 V accessory socket
the audio and telematics systems.
FOCAL® Hi-Fi system
The USB socket allows the connection of a
portable device or a USB memory stick.
► Plug in a 12 V accessory (with a maximum
It reads the audio files that are sent to your audio
rated power of 120 W) using a suitable adapter.
system and played via the vehicle's speakers.
Observe the maximum power rating to
These files can be managed using the steering-
avoid damaging the accessory.
mounted controls or those on the touch screen.
Depending on version, the USB
socket located on the centre
The connection of an electrical device
The vehicle is equipped with a high-fidelity
console also allows a smartphone to be
not approved by PEUGEOT, such as a
acoustic system from the French brand FOCAL®.
connected by Android Auto® or CarPlay®,
USB charger, may adversely affect the
10 speakers incorporating exclusive FOCAL®
enabling certain smartphone applications to be
operation of vehicle electrical systems,
technologies offer the pleasure of pure and
used on the touch screen.
causing faults such as poor radio reception or
detailed sound inside the vehicle:
For best results, use a cable made or approved
interference with displays in the screens.
- Polyglass technology central speaker/mid-
by the device manufacturer.
range satellite speakers: sound immersion and
These applications can be managed using the
spatialisation.
USB socket
steering-mounted controls or the audio system
- Polyglass technology woofers/mid-ranges with
These symbols determine the type of use of a
controls.
high excursion: balance, dynamics and precision
USB socket:
of sound.
63
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст