Peugeot 3008 Hybrid 4 (2017 year). Instruction — part 9
3
Ease of use and comfort
127
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Mats
When fitting the mat for the first time, on the
driver's side use only the fixings provided in the
wallet attached.
The other mats are simply placed on the
carpet.
Removal
Refitting
To avoid any risk of jamming of the
pedals:
-
only use mats which are suited to
the fixings already present in the
vehicle; these fixings must be used,
-
never fit one mat on top of another.
The use of mats not approved by
PEUGEOT may interfere with access to
the pedals and hinder the operation of
the cruise control / speed limiter.
The mats approved by PEUGEOT have
two fixings located below the seat.
Fitting
To remove the mat on the driver's side:
F move the seat as far back as possible,
F unclip the fixings,
F remove the mat.
To refit the mat on the driver's side:
F position the mat correctly,
F refit the fixings by pressing,
F check that the mat is secured correctly.
128
Ease of use and comfort
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
1. Front courtesy lamp
2. Front map reading lamps
Courtesy lamps
Front and rear courtesy lamps
Front and rear map reading
lamps
It switches off gradually:
-
when the vehicle is locked,
-
when the ignition is switched on,
-
30 seconds after the last door is closed.
In permanent lighting mode, the lighting time
varies according to the circumstances:
-
with the ignition off, approximately ten minutes,
-
in energy economy mode, approximately
thirty seconds,
-
with the engine running, unlimited.
Take care not to put anything in contact
with the courtesy lamps.
3. Rear courtesy lamp
4. Rear map reading lamps
When the courtesy lamp is in the
"permanent lighting" position, the rear
courtesy lamp also comes on, except if
it is in the "permanently off" position.
To switch off the rear courtesy lamp, put
it in the "permanently off" position.
In this position, the courtesy
lamp comes on gradually:
-
when the vehicle is unlocked,
-
when the key is removed from the ignition,
-
on opening a door,
-
when the remote control locking button is
used to locate your vehicle.
Permanently off.
Permanent lighting.
F With the ignition on, press the
corresponding switch.
3
Ease of use and comfort
129
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Interior mood lighting
The dimmed passenger compartment lighting improves visibility in the vehicle when the light is poor.
The interior mood lighting switches off
automatically when the sidelamps are switched
off.
At night, the interior mood lighting comes on
automatically when the sidelamps are switched
on.
The interior mood lighting can be
activated or deactivated and its
brightness adjusted in the Driving
menu of the touch screen.
The interior mood lighting is also
managed by the i-Cockpit Amplify
function.
Depending on version, the interior mood
lighting includes:
-
two LEDs located in the front courtesy
lamp,
-
a light source in the storage compartment
at the front of the centre console,
-
a light source for each of the front
footwells,
-
light guides on the front door panels and
the sides of the centre console,
-
illuminated bezels for the front cup holders,
-
a light source for each of the front door
pockets,
-
illuminated rails for the panoramic sunroof
blind.
For more information on the i-Cockpit Amplify
function, refer to the corresponding section.
130
Ease of use and comfort
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Rear seats
Rear head restraints
Bench seat with a fixed cushion and split folding backrests (2/3-1/3) to adapt the boot load space.
They have two positions:
- a
high position, for when the seat is in
use:
F pull the head restraint fully up.
- a
low position, for stowing, when the seat
is not in use:
F press the lug A to release the head
restraint and push it fully down.
The rear head restraints can be removed.
Never drive with passengers seated at
the rear when the head restraints are
removed; they must be in place and in
the high position.
The head restraint for the centre seat
and those for outer seats are not
interchangeable.
To remove a head restraint:
F pull the head restraint as far up as it will go,
F press the lug A to release the head
restraint and remove it completely,
F stow the head restraint.
To refit a head restraint:
F introduce the rods of the head restraint
into the guides of the corresponding seat
backrest,
F push the head restraint down as far as it
will go,
F press the lug A and then push the head
restraint fully down.
3
Ease of use and comfort
131
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
The folding of the backrest is
accompanied by a slight lowering of the
corresponding cushion.
To obtain a flat surface, it is necessary
to place the adjustable boot floor in the
high position.
When the backrest is released, the red
indicator is visible in the release grip.
Folding from the passenger compartment
F Press the backrest release grip 1.
F Guide the backrest 3 down to the horizontal
position.
Folding the backrests
Each section of the backrest has two release
controls:
-
a grip 1 on the outer edge of the backrest,
-
a lever 2 on the boot side trim.
First:
F lower the head restraints,
F if necessary, move the front seats forward,
F fold away the rear armrest,
F check that nothing or no person might
interfere with the folding of the backrests
(clothing, luggage, ...),
F check that the outer seat belts are lying
correctly on the backrests.
Folding or unfolding the seat backrests
must only be done with the vehicle
stationary.
132
Ease of use and comfort
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Returning the backrests to
their original position
Folding from the boot
F Pull the backrest release lever 2 towards
you.
The backrest 3 folds fully onto the cushion.
First check that the outer seat belts are
lying vertically alongside the backrest
latching rings.
F Put the backrest 3 in the upright position
and push on it to latch it home.
F Check that the red indicator is no longer
visible in the release grip 1.
F Ensure that the outer seat belts are not
trapped during the manoeuvre.
Caution, a backrest that has not latched
correctly compromises the safety of
passengers in the event of sudden
braking or an accident.
The contents of the boot may be thrown
forward - Risk of serious injury!
3
Ease of use and comfort
133
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Rear fittings
A 230 V / 50 Hz socket (maximum power:
150 W) is located on the back of the centre
console under a protective cover.
This socket works with the engine running, as
well as in STOP mode with Stop & Start.
F Raise the protective cover.
F Check that the green indicator lamp is on.
F Connect your multimedia or other electrical
device (telephone charger, laptop
computer, CD-DVD player, baby food
warmer...).
230 V / 50 Hz power socket
In the event of a fault with the socket, the green
warning lamp flashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Connect only one device at a time to
the socket (no extension or multi-way
connector).
Connect only devices with class II
insulation (shown on the device).
Do not use a device with a metal case
(electric shaver, ...).
As a safety measure, when electrical
consumption is high and when required
by the vehicle's electrical system
(particular weather conditions, electrical
overload...), the current supply to
the socket will be cut off; the green
indicator lamp goes off.
F To connect a 12 V accessory (max power:
120 W), lift the cover and connect a
suitable adaptor.
12 V accessory socket
The connection of an electrical device
not approved by PEUGEOT, such as a
USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor telephone
reception or interference with displays
in the screens.
134
Ease of use and comfort
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Rear armrest
F Lower the rear armrest for a more
comfortable position.
The armrest incorporates two cup holders.
Ski flap
Opening
F Lower the rear armrest.
F Pull the flap handle downwards.
F Lower the flap.
F Load the objects from inside the boot.
Comfort and storage arrangement for rear
passengers.
Arrangement for storing and transporting long
objects.
3
Ease of use and comfort
135
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Boot fittings
1. Load space cover
2. 12 V accessory socket (120 W)
3. Boot lamp
4. Rear seat folding controls
5. Hooks
6. Stowing rings
7. Adjustable boot floor (2 positions)
8. Storage well / Tool box under the floor
The stowing rings are designed for
securing luggage by attaching a
retaining net to the rings.
Such nets are available as an option or
as an accessory.
For more information, contact a
PEUGEOT dealer.
For the installation of a high load
retaining net, refer to the corresponding
section.
136
Ease of use and comfort
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Luggage cover
It is in two parts:
-
a fixed part with an open storage space,
-
a mobile part which rises as the tailgate
opens, with an open storage space.
To remove the luggage cover:
F unhook the two cords,
F raise the moving part slightly, then unclip it
on each side,
F unclip the fixed part on each side, then
remove the luggage cover.
The luggage cover can be stowed under the
boot floor.
Under sudden deceleration, objects
placed on the luggage cover may be
turned into projectiles.
12 V accessory socket
F To connect a 12 V accessory (max power:
120 W), remove the cap and connect an
appropriate adaptor.
F Switch on the ignition.
The connection of an electrical device
not approved by PEUGEOT, such as a
USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor telephone
reception or interference with displays
in the screens.
3
Ease of use and comfort
137
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
High load retaining net
This removable net allows the use of the entire
loading volume up to the roof:
-
behind the front seats (row 1) when the rear
seats are folded,
-
behind the rear seats (row 2) when the
luggage cover is removed.
It provides protection for the occupants of the
vehicle in the event of sudden braking.
Behind the front seats
F Fold the rear seats.
F Remove the cover trims located on each
side of the roof.
F Position the net's upper hooks in the roof,
on each side in turn.
F Attach the net straps to the lower
anchorages, located on the front seat outer
runners.
F Pull on the straps to stretch the net.
Behind the rear seats
F Remove the luggage cover.
F Remove the cover trims on each side,
located high up in the roof.
F Position the net's upper hooks in the roof,
on each side in turn
F Attach the net straps to the lower rings,
located on each of the boot side trims.
F Pull on the straps to stretch the net.
Once fitted, the net does not prevent
folding of the rear seat backrests.
138
Ease of use and comfort
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Adjustable boot floor
This two-position floor allows you to optimise
the volume of the boot by means of the outer
stops placed on the sides:
-
High position (100 kg max): you obtain a
flat floor up to the front seats, when the
rear seats are folded.
-
Low position (150 kg max): maximum boot
volume.
To change the height of the floor:
F Push the floor fully forwards then use the
side stops to move the floor to the desired
position.
To support the floor in the raised position:
F From the high position, raise the floor
towards the load space cover.
F Take it past the retractable stops, then rest
the floor on these stops.
On certain versions, the adjustable boot
floor cannot be fitted in the low position.
3
Ease of use and comfort
139
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Sliding boot floor
F From the high position, press the handle
and pull the boot floor towards you, as far
as it will go.
This position facilitates loading and unloading
of the boot.
Maximum load: 100 kg.
Storage well
F Raise the boot floor fully for access to the
storage well.
Depending on version, this houses:
-
a temporary puncture repair kit with the
vehicle's tools,
-
a spare wheel with the vehicle's tools.
It also allows storage of the luggage cover.
140
Ease of use and comfort
3008-2_en_Chap03_ergonomie-et-confort_ed01-2016
Boot lamp
This comes on automatically when the boot is
opened and goes off automatically when the
boot is closed.
The lighting time varies according to the
circumstances:
-
when the ignition is off, approximately
ten minutes,
-
in energy economy mode, approximately
thirty seconds,
-
when the engine is running, no limit.
4
Lighting and visibility
141
3008-2_en_Chap04_eclairage-et-visibilite_ed01-2016
Without AUTO lighting
With AUTO lighting
F Turn the ring A to place the desired symbol
against the mark.
Exterior lighting control stalk
Lighting off (ignition off) /
Daytime running lamps (engine running).
Automatic illumination of headlamps.
Daytime running lamps / Dipped
beam / Main beam.
Sidelamps only.
Dipped or main beam headlamps.
Displays
Selection of main lighting mode
Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
Headlamp dipping
F Pull the stalk B toward you to switch
between dipped and main beam
headlamps.
In the lighting off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining a
pull on the stalk.
Main lighting
"Highway" function
On versions fitted with "Full LED"
technology headlamps, the range
of the dipped beam headlamps is
automatically increased once the
speed of the vehicle is above 68 mph
(110 km/h).
A fault with a lamp is signalled by
the permanent illumination of this
warning lamp, accompanied by the
display of a message and an audible
signal.
Lighting and visibility
142
3008-2_en_Chap04_eclairage-et-visibilite_ed01-2016
In good or rainy weather, by both
day and night, use of the front and
rear foglamps is prohibited. In these
situations, the power of their beams
may dazzle other drivers. They should
only be used in fog or falling snow.
In these weather conditions, you should
switch on the foglamps and dipped
beam headlamps manually, as the
sunshine sensor may detect sufficient
light.
Do not forget to switch off the foglamps
when they are no longer necessary.
Foglamps
Rear foglamps
The sidelamps or dipped or main beam
headlamps must be on.
Front and rear foglamps
The main or dipped beam headlamps
must be on.
Rotate and release ring C:
F forward to switch on the rear foglamps.
F backward to switch them off.
Rotate and release ring C:
F forward a first time to switch on the front
foglamps,
F forward a second time to switch on the rear
foglamps,
F backward a first time to switch off the rear
foglamps,
F backward a second time to switch off the
front foglamps.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст