Peugeot 307 SW Dag (2007.5). Instruction — part 2
20
INSTRUMENTS and CONTROLS
1.
Engine oil temperature indicator.
2.
Sport programme indicator light.
3.
Gear lever position indicator.
4.
Snow programme indicator light.
5. Rev counter.
6.
Coolant temperature indicator.
7.
Low fuel level warning light.
8. Fuel gauge.
9.
Speedometer.
10.
Service indicator, oil level indica-
tor, distance recorder and cruise
control/speed limiter.
11.
Trip recorder zero reset button.
12. Lighting rheostat button.
13.
Left-hand direction indicator.
14.
Central STOP warning light.
15.
Right-hand direction indicator.
16.
Service warning light.
17.
Handbrake, brake l uid level and
electronic brake force distribution
warning light.
18.
Anti-lock braking system(ABS)
warning light.
19. Electronic stability control(ESP/
ASR) warning light.
20. Driver's seat belt not fastened
warning light.
21.
Emission control system warning
light.
22.
Air bags warning light.
23.
Passenger air bag disarmed indi-
cator light * .
24.
Dipped beam headlamps indica-
tor light.
25.
Main beam headlamps indicator
light.
26.
Front fog lamps indicator light.
27.
Rear fog lamp indicator light.
28.
Engine oil pressure warning light * .
29.
Battery charge warning light * .
PETROL SPORT INSTRUMENT PANEL DIALS: AUTOMATIC
GEARBOX
* According to country.
21
INSTRUMENTS and CONTROLS
OPERATION WARNING
LIGHTS
A permanently lit warning light or
one that l ashes with the engine
running, indicates an operating fault
in the relevant unit. Some warning
lights may be linked to buzzers and
a message on the multifunction dis-
play. Do not ignore this warning:
contact a PEUGEOT dealer as soon
as possible.
If the Central STOP warning light
comes on when you are driving,
stop immediately where it is safe
to do so.
Central STOP
warning light
This light comes on
for a few seconds
each time the ignition is switched on.
It is linked to the "engine oil pres-
sure" * , "low brake l uid level" and
"electronic brake force distribution
fault" warning lights and the coolant
temperature gauge.
Stop immediately if it l ashes with
the engine running .
Contact a PEUGEOT dealer.
It also comes on in the event of a
puncture, accompanied by an audible
signal and a message on the multi-
function display locating the wheel
concerned.
Service warning light
This light comes on for a
few seconds each time
the ignition is switched on.
If it remains on or comes
on when the engine is running, ac-
companied by an audible signal and
a message on the multifunction dis-
play, it indicates one of the following:
- a battery charge fault * ,
- an automatic gearbox operation
fault,
- an engine immobiliser system
fault,
- an engine management system
fault,
- a speed control system fault
(cruise control/speed limiter),
- a rear parking assistance system
fault,
- an automatic switching on of the
lights system fault,
- an automatic headlamp adjust-
ment system fault,
- a tyre under-inl ation detection
system fault ,
- a del ated tyre,
- a l at remote control battery,
- one or more door(s) open at a vehi-
cle speed above 6 mph (10 km/h),
- a low diesel additive reservoir
level (Diesel),
- a lack of engine oil,
- the start of saturation of the par-
ticle emission i lter (Diesel) due
to exceptionally prolonged urban
driving conditions: low speed,
long trafi c jams, ...
In order to regenerate the i l-
ter, you are advised to drive at
a speed of 40 mph (60 km/h) or
above for at least i ve minutes
(until the warning light is switched
off) as soon as possible, when
trafi c conditions permit. If the
warning light remains on, contact
a PEUGEOT dealer.
During regeneration of the par-
ticle emission i lter, relay noise
may be heard from underneath
the fascia.
- the presence of water in the die-
sel i lter (Diesel) * .
Risk of damage to the injection
system.
Contact a PEUGEOT dealer as
soon as possible.
- a low coolant level ** .
Stop immediately.
Warning:
wait for the engine to
cool before topping up the level.
The cooling system is pressu-
rised.
In order to avoid any risk of scal-
ding, unscrew the cap by two
turns to allow the pressure to
drop. When the pressure has
dropped, remove the cap and top
up the level.
Contact a PEUGEOT dealer.
* According to country.
** According to engine.
22
INSTRUMENTS and CONTROLS
Electronic stability
programme (ESP/ASR)
warning light
This comes on for a few
seconds each time the igni-
tion is switched on.
If the light remains on or comes on
when the engine is running and the
vehicle is moving, it is accompanied
by an audible signal and a message
on the multifunction display; contact
a PEUGEOT dealer.
When the engine is running and the
vehicle is moving, it l ashes if the
system is activated.
It is lit continuously when the system
is disarmed.
Emission control system
warning light
This comes on each time
the ignition is switched on.
It should switch off a few seconds af-
ter the engine is started.
If the light comes on when the en-
gine is running,accompanied by an
audible signal and a message on the
multifunction display,this indicates a
malfunction of the emission control
system.
Contact a PEUGEOT dealer as soon
as possible.
Handbrake, low brake
l uid level and electronic
brake force distribution
fault warning light
Linked to the central STOP
warning light.
This comes on for a few seconds
each time the ignition is switched
on.
Illumination of this light is accompa-
nied by an audible signal and a mes-
sage on the multifunction display
indicating:
- that the handbrake is applied or
has not been released correctly,
- an excessive drop in the brake
l uid level (if the light remains
on even with the handbrake re-
leased),
- a malfunction of the electronic
brake force distribution, if linked
to the ABS warning light.
Stop immediately
in the last two
cases.
Contact a PEUGEOT dealer.
Anti-lock braking system
(ABS) warning light
This light comes on for a
few seconds each time the
ignition is switched on.
If it remains on or comes on above
8 mph (12 km/h),this indicates a mal-
function of the ABS.
However, the vehicle retains conven-
tional servo-assisted braking.
Illumination of this light is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Seat belt unfastened/not
fastened warning light
When the ignition is switched
on, the light comes on if the
driver has not fastened his
seat belt.
With the engine running and the
doors closed, the light switches off
automatically after 30 seconds.
If the seat belt is unfastened:
- below 12 mph (20 km/h), the light
comes on constantly,
- above 12 mph (20 km/h) and for
two minutes, the light l ashes ac-
companied by an audible signal
of increasing volume. Once these
two minutes have elapsed, the
light remains on until the driver
fastens his seat belt.
23
INSTRUMENTS and CONTROLS
Battery charge warning
light *
This comes on for a few
seconds each time the igni-
tion is switched on.
If it comes on with the engine run-
ning, it is accompanied by an audible
signal and a message on the multi-
function display.
According to country, this warning
light may be replaced by the service
warning light.
It can indicate:
- faulty operation of the charging
circuit,
- loose battery or starter terminals,
- a cut or slack alternator belt,
- an alternator fault.
Contact a PEUGEOT dealer.
Low fuel level
warning light
This comes on for a
few seconds each
time the ignition is
switched on.
When this light comes on with the en-
gine running, it is accompanied by an
audible signal and a message on the
multifunction display.
When the warning light comes on, you
have enough fuel left to drive approxi-
mately 30 miles (50 km) . The tank
capacity is approximately 60 litres.
Diesel pre-heat light
This comes on for a few
seconds each time the igni-
tion is switched on.
Wait until it goes out before trying the
starter.
Engine oil pressure
warning light *
Linked to the central STOP
warning light.
If it comes on with the engine run-
ning, it is accompanied by an audible
signal and a message on the multi-
function display.
Stop immediately.
If there is a lack of oil in the lubrica-
tion circuit, top up the level.
Contact a PEUGEOT dealer without
delay.
Engine oil pressure warning *
Linked to the central STOP
warning
light.
When the engine is running, the en-
gine oil pressure warning message is
accompanied by an audible signal.
Stop immediately .
If there is a lack of oil in the lubrica-
tion circuit, top up the level.
Contact a PEUGEOT dealer as soon
as possible.
Air bag warning light
This comes on for a few
seconds each time the igni-
tion is switched on.
Illumination of this warning light, with
the engine running, is accompanied
by an audible signal and a message
on the multifunction display indicat-
ing:
- a fault in the front air bags,
or
- a fault in the side air bags or cur-
tain air bags.
Contact a PEUGEOT dealer.
Passenger air bag
disarmed indicator light *
This comes on for a few
seconds each time the igni-
tion is switched on.
If the passenger air bag is disarmed,
the indicator light remains on.
In all cases, if the indicator light
l ashes,contact a PEUGEOT dealer.
* According to country.
24
INSTRUMENTS and CONTROLS
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high. The central
STOP
warning light l ashes, accom-
panied by an audible signal and a
message on the multifunction dis-
play.
You must stop immediately.
Warning:
wait for the engine to cool
before topping up the level.
The cooling system is pressurised.
In order to avoid any risk of scalding,
unscrew the cap two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level.
Contact a PEUGEOT dealer.
Coolant temperature indicator
When the engine is running, this indi-
cates the temperature of the oil.
The temperature is too high if the
maximum graduation is reached.
You must stop immediately.
Contact a PEUGEOT dealer.
Park
Automatic gearbox lever
positions indicator
Reverse
Neutral
Drive
Manual mode:
1st gear engaged
2nd gear engaged
3rd gear engaged
4th gear engaged
Engine oil temperature
indicator
5th gear *** engaged
6th gear *** engaged
*** According to model.
25
INSTRUMENTS and CONTROLS
In the event of under-revving or over-
revving, the gear selected l ashes for
a few seconds, then the actual gear
engaged is displayed.
This comes on when the
"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the
"SNOW"
programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light
This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note
: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since
the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.
Example: 4,800 miles/km remain
before the next service. For i ve sec-
onds after the ignition is switched on,
the display indicates:
INSTRUMENT PANEL
DISPLAY
26
INSTRUMENTS and CONTROLS
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , re-
lease the button; the spanner disap-
pears.
Important:
after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least i ve
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The spanner l ashes for 5 seconds
after the ignition is switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit. The display indi-
cates the total and trip distance.
Note:
the spanner may also come on
if more than two years have elapsed
since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
Service indicator zero re-set
27
INSTRUMENTS and CONTROLS
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service informa-
tion.
Oil level correct
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunc-
tion of the engine
oil level gauge.
Contact a PEUGEOT
dealer.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
Flashing of "OIL" ,
linked with the serv-
ice warning light,
accompanied by an
audible signal and
a message on the
multifunction display, indicates a lack
of oil which could damage the engine.
If the lack of oil is coni rmed by a
check using the dipstick, it is essen-
tial that the level is topped up.
Lack of oil
Dipstick
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up the
level via the oil i ller cap,
using the type of oil suit-
ed to your engine.
A
= max.
B = min.
Trip recorder zero reset
button
Lighting rheostat
25
INSTRUMENTS and CONTROLS
In the event of under-revving or over-
revving, the gear selected l ashes for
a few seconds, then the actual gear
engaged is displayed.
This comes on when the
"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the
"SNOW"
programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light
This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note
: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since
the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.
Example: 4,800 miles/km remain
before the next service. For i ve sec-
onds after the ignition is switched on,
the display indicates:
INSTRUMENT PANEL
DISPLAY
25
INSTRUMENTS and CONTROLS
In the event of under-revving or over-
revving, the gear selected l ashes for
a few seconds, then the actual gear
engaged is displayed.
This comes on when the
"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the
"SNOW"
programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light
This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note
: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since
the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.
Example: 4,800 miles/km remain
before the next service. For i ve sec-
onds after the ignition is switched on,
the display indicates:
INSTRUMENT PANEL
DISPLAY
26
INSTRUMENTS and CONTROLS
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , re-
lease the button; the spanner disap-
pears.
Important:
after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least i ve
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The spanner l ashes for 5 seconds
after the ignition is switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit. The display indi-
cates the total and trip distance.
Note:
the spanner may also come on
if more than two years have elapsed
since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
Service indicator zero re-set
26
INSTRUMENTS and CONTROLS
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , re-
lease the button; the spanner disap-
pears.
Important:
after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least i ve
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The spanner l ashes for 5 seconds
after the ignition is switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit. The display indi-
cates the total and trip distance.
Note:
the spanner may also come on
if more than two years have elapsed
since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
Service indicator zero re-set
27
INSTRUMENTS and CONTROLS
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service informa-
tion.
Oil level correct
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunc-
tion of the engine
oil level gauge.
Contact a PEUGEOT
dealer.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
Flashing of "OIL" ,
linked with the serv-
ice warning light,
accompanied by an
audible signal and
a message on the
multifunction display, indicates a lack
of oil which could damage the engine.
If the lack of oil is coni rmed by a
check using the dipstick, it is essen-
tial that the level is topped up.
Lack of oil
Dipstick
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up the
level via the oil i ller cap,
using the type of oil suit-
ed to your engine.
A
= max.
B = min.
Trip recorder zero reset
button
Lighting rheostat
28
INSTRUMENTS and CONTROLS
TRIP COMPUTER
Press the button, located at the
end of the wipers stalk
, to dis-
play the various items of trip com-
puter data in succession.
The trip computer data is the following:
System which provides current infor-
mation concerning the route travelled
(range, consumption, ...).
Press the control for more than
two seconds to reset the distance
travelled, the average consump-
tion and the average speed to
zero.
Monochrome display A
Zero reset
Data displays
- the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.
The next press then returns you
to the normal display.
29
INSTRUMENTS and CONTROLS
- the current information
tab with:
• the range,
•
the current consumption,
•
the distance remain-
ing to be travelled,
Colour display
Route zero reset
Monochrome display C
Press the button, located at the
end of the wipers stalk
, to dis-
play the various trip computer
tabs in succession:
Data displays
- the route "1" tab with:
the distance travelled,
•
the average consump-
tion,
•
the average speed,
for the i rst route.
- the route "2" tab with:
•
the distance trav-
elled,
•
the average con-
sumption,
•
the average speed,
for
the
second
route.
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, consumption, …).
When the route required is dis-
played, press the control for more
than two seconds.
Routes "1" and "2"
are independent
but their use is identical.
Route "1"
permits, for example, daily
calculations, and route "2" monthly
calculations.
30
INSTRUMENTS and CONTROLS
Distance remaining to be
travelled
(km or miles)
This is the distance remain-
ing to be travelled to the i nal destina-
tion. It is either calculated instantly by
the navigation system if guidance is
activated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed
(km/h or mph)
This is the average speed
calculated since the last
trip computer zero reset
(ignition on).
Range
(km or miles)
This indicates the number
of miles (or kilometres)
which can still be travelled with the
fuel remaining in the tank in relation
to the average consumption over the
last few miles (kilometres) travelled.
Current consumption
(l/100 km or km/l or mpg)
This is the average quantity
of fuel consumed over the
last few seconds.
Average consumption
(l/100 km or km/l or mpg)
This is the average quan-
tity of fuel consumed since
the last trip computer zero reset.
Distance travelled
(km or miles)
This indicates the dis-
tance travelled since the
last trip computer zero
reset.
A few definitions…
When the range falls below 20 miles
(30 km), dashes are displayed. After
i lling with at least 5 litres of fuel, the
range is recalculated and is displayed
when it exceeds 60 miles (100 km).
If dashes are displayed con-
tinuously while driving in
place of the digits, contact a
PEUGEOT dealer.
This function is only displayed
from 20 mph (30 km/h).
This i gure may increase fol-
lowing a change of driving
style or relief, resulting in a
signii cant change in the cur-
rent consumption.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст