Peugeot Expert (2022 year). Manual in english — page 7
Safety
IL:
Seat position suitable for the installation
(b) The seat can be installed centrally in the
(3)
Installation possible only behind the driver's
5
of an Isofix Semi-UniversaL seat which is
vehicle; it then prevents the use of the outer
seat with individual passenger seat.
either:
seats.
(4)
The seat in row 2 must be adjusted so that
- "rearward facing" fitted with an upper
there is no contact between the child in row
strap or a support leg,
For information on securing the upper
3 and the seat immediately in front.
- "forward facing" fitted with a support leg,
strap using the ISOFIX mountings, refer
- a carrycot fitted with an upper strap or a
to the corresponding section.
(5)
The front seat must be adjusted so that
support leg.
there is no contact between the child in row
(1) Installing a carrycot on this seat may
2 and the seat immediately in front.
X: Seat position not suitable for the installation
prevent the use of one or more of the other
of an ISOFIX child seat or carrycot for the
seats in this row.
(6)
The front seat must be adjusted so that
specified weight group.
there is no contact between the child in row
(2) Installation possible only behind the driver's
2 and the seat immediately in front (with the
(a)
Refer to the current legislation in the country
seat.
front seat adjusted to 2 notches ahead of
in which you are driving before placing a
the centre of the slide).
child in this seat position.
i-Size child seats
i-Size child seats have two latches that are anchored to the two rings A.
These i-Size child seats also have:
- either an upper strap that is attached to ring B.
- or a support leg that rests on the vehicle floor, compatible with the approved i-Size seat position.
Their role is to prevent the child seat from tipping forward in the event of a collision.
For more information on the ISOFIX mountings, refer to the corresponding section.
127
Safety
Locations for i-Size child seats
In accordance with the new European regulations, this table indicates the options for installing i-Size child seats on seats in the vehicle fitted with i-Size
approved ISOFIX mountings.
Seat
i-Size restraint system
Passenger seat with passenger
Not i-Size
airbag deactivated "OFF" or
activated "ON"
Row 1 (a)
With 2-seat bench seat in row 1
Outer seats
Not i-Size
Centre seat
Not i-Size
Row 2
With individual seats in row 1
Outer seats
Not i-Size
Centre seat
Not i-Size
128
Safety
Seat
i-Size restraint system
5
Combi, Business, Active
With 2-seat bench seat in row 1
Fixed one-piece bench seat, outer
i-UF
seats and centre seat (b)
Row 2
Seat and bench seat, outer seats
i-UF
and centre seat (b)
With individual seats in row 1
Fixed one-piece bench seat, outer
i-U
seats and centre seat (b)
Seat and bench seat, outer seats
i-U
and centre seat (b)
Combi, Business, Active
Fixed one-piece bench seat, outer
i-U (c)
seats and centre seat (b)
Seat and bench seat, outer seats
i-U (c)
Row 3
and centre seat (b)
129
Safety
Seat
i-Size restraint system
Allure, Business VIP
Rear seats with seat and bench
i-U (c)
seat
Rear seats with 2 individual seats
i-UF (c, d)
Row 2 and 3
(Excluding group 0)
Rear seats with 1 individual seat
i-UF (c, d)
(Excluding group 0)
i-U: Suitable for forward facing and rearward facing "Universal" i-Size restraint systems.
i-UF: Only suitable for forward facing "Universal" i-Size restraint systems.
(a) Refer to the current legislation in the country in which you are driving before placing a child in this seat position.
(b) The seat can be installed centrally in the vehicle; it then prevents the use of the outer seats.
(c) The seat in row 2 cannot be used when an i-Size child seat is installed immediately behind.
(d) Install an i-Size child restraint system only if seats are installed in forward direction.
Locking/Unlocking
Manual child lock
► Rotate the control located on the edge of the
Mechanical system to prevent opening of the
side door up to lock it, or down to unlock it.
sliding side door using its interior lever.
130
Safety
Any other status of the indicator lamp
Electric child lock
5
indicates a malfunction of the electric
Remote control system to
child lock.
prevent opening of the rear
doors (sliding side door(s), side-
With the child lock activated, it is still
hinged rear doors or tailgate
possible to open the doors from outside.
(depending on version)) using
their interior controls.
This system is independent and in no
This control prevents the opening of the rear
circumstances does it take the place of
doors using their interior handles and the use of
the central locking control.
the rear electric windows.
Check the status of the child lock each time
► The system is locked/unlocked using the
you switch on the ignition.
remote control key or the back-up key for the
Activation/Deactivation
Always keep the electronic key with you when
Keyless Entry and Start system.
leaving the vehicle, even for a short time.
In the event of a serious impact, the electric
child lock is switched off automatically to
permit the exit of the rear passengers.
Child lock on rear
windows
► With the ignition on, press this button to
This mechanical system
activate/deactivate the child lock.
prevents opening of the left-
A message is displayed, confirming activation/
hand and/or right-hand rear side
deactivation of the child lock.
windows.
When the indicator lamp is on, the child lock is
activated.
In the event of a serious impact, the
electric child lock is deactivated
automatically.
131
Driving
Be aware of the effect of side winds on the
Never drive on surfaces covered with
Driving recommendations
vehicle.
vegetation (e.g. tall grass,
► Observe the driving regulations and remain
Maintenance
accumulated dead leaves, crops, debris)
vigilant whatever the traffic conditions.
such as a field, a country lane overgrown
► Monitor your environment and keep your
Inflate to the minimum pressure indicated on the
with bushes or a grassy verge.
hands on the wheel to be able to react to
label, or even over-inflate by 0.2 to 0.3 bar for
This vegetation could come into contact with
anything that may happen any time.
long journeys.
the vehicle's exhaust system or other systems
► Drive smoothly, anticipate the need for
which are very hot. Risk of fire!
Important!
braking and maintain a longer safety distance,
especially in bad weather.
Never leave the engine running in a
Make sure you do not leave any item in
► Stop the vehicle before performing operations
closed space without sufficient
the passenger compartment which could
that require sustained attention (e.g. settings).
ventilation. Internal combustion engines emit
act like a magnifying glass under the effect of
► During long trips, take a break every 2 hours.
toxic exhaust gases such as carbon
the sun's rays and cause a fire. Risk of fire or
To ensure the durability of the vehicle and
monoxide. Danger of poisoning and death!
damage to interior surfaces!
for safety reasons, remember that certain
precautionary measures must be taken when
In very severe wintry conditions
Never leave the vehicle unattended,
driving the vehicle:
(temperature below -23°C), let the engine
with the engine running. If you have to
Manoeuvre cautiously, at low speed
run for 4 minutes before moving off, to ensure
leave your vehicle with the engine running,
Manoeuvre slowly.
the correct operation and durability of the
apply the parking brake and put the gearbox
Before turning, check that there are no obstacles
mechanical components of your vehicle
into neutral or position N or P (depending on
at mid-height along the sides.
(engine and gearbox).
the type of gearbox).
Before reversing, check that there are no
obstacles, particularly at high level behind the
Never drive with the parking brake
Never leave children inside the vehicle
vehicle.
applied. Risk of overheating and
unsupervised.
Be aware of the external dimensions, if ladders
damaging the braking system!
are fitted.
On flooded roads
Drive the vehicle carefully
Never park the vehicle and never
We strongly advise against driving on flooded
Take corners gently.
leave the engine running on a
roads, as this could cause serious damage to the
Anticipate the need to brake as the stopping
flammable surface (e.g. dry grass, dead
engine or gearbox, as well as to your vehicle's
distance is increased, particularly on wet or icy
leaves).The vehicle exhaust system is very
electrical systems.
roads.
hot, even several minutes after the engine
stops. Risk of fire!
132
Driving
Cooling the traction battery
If the outside temperature is high, let the
6
The cooling fan comes on during
engine idle for 1 to 2 minutes after the
charging to cool the on-board charger and the
vehicle comes to a stop, to help it to cool.
traction battery.
Before setting off
On the inside
Nose weight
During use, you may hear certain perfectly
If the vehicle absolutely must drive through a
normal noises specific to electric vehicles, such
► Distribute the load in the trailer so that the
flooded section of road:
as:
heaviest items are located as close as possible
► Check that the depth of the water does not
- Traction battery relay when starting.
to the axle, and the nose weight (at the point
exceed 15 cm, taking account of waves that
- Vacuum pump when braking.
where it joins your vehicle) approaches the
might be generated by other users.
- Vehicle tyres or aerodynamics when driving.
maximum permitted, without exceeding it.
► Deactivate the Stop & Start function.
- Jolting and knocking noise during hill starts.
► Drive as slowly as possible without stalling. In
Tyres
all cases, do not exceed 6 mph (10 km/h).
► Check the tyre pressures of the towing
Towing
► Do not stop and do not switch off the engine.
vehicle and of the trailer, observing the
On leaving the flooded road, as soon as safety
Driving with a trailer places greater
recommended pressures.
conditions allow, make several light brake
demands on the towing vehicle and
Lighting
applications to dry the brake discs and pads.
particular care must be taken.
► Check the electrical signalling on the trailer
If in doubt about the state of your vehicle,
and the headlamp beam height of your vehicle.
contact a PEUGEOT dealer or a qualified
Do not exceed the maximum towable
workshop.
If a genuine PEUGEOT towing device is
weights.
At altitude: reduce the maximum load by
used, the rear parking sensors will be
Noise (Electric)
deactivated automatically to avoid activating
10% per 1,000 metres of altitude; the lower
On the outside
air density at high altitudes decreases engine
the audible signal.
performance.
Due to the vehicle’s quiet operation when
driving, the driver must pay particular attention.
When driving
When manoeuvring, the driver must always
New vehicle: do not tow a trailer until the
Cooling
check the vehicle's immediate surroundings.
vehicle has driven at least 620 miles
At speeds of up to 19 mph (30 km/h), the
(1,000 kilometres).
Towing a trailer uphill causes the coolant
pedestrian horn warns other road users of the
temperature to increase. The maximum towable
vehicle’s presence.
load depends on the gradient and the exterior
133
Driving
temperature. The fan’s cooling capacity does not
In the event of a fault, you are informed
With the conventional key / With the
increase with engine speed.
by illumination of this warning lamp, an
remote control key
► Reduce speed and lower the engine speed to
audible signal and a message on the screen.
limit the amount of heating produced.
The vehicle will not start; contact a PEUGEOT
► Pay constant attention to the coolant
dealer as soon as possible.
temperature.
If this warning lamp and the
Starting/switching off the
STOP warning lamp come
on, stop the vehicle and switch off the engine as
engine
soon as possible.
Brakes
Starting
Using the engine brake is recommended to limit
The parking brake must be applied.
the overheating of the brakes. Braking distances
are increased when towing a trailer.
► With a manual gearbox, place the gear
1. Stop position.
lever in neutral, fully depress the clutch pedal
2. Ignition on position.
Side wind
and keep the pedal down until the engine starts.
3. Starting position.
Bear in mind that the vehicle will be more
► With an automatic gearbox, place the
► Insert the key into the ignition switch. The
susceptible to wind when towing.
selector in position P then depress the brake
system recognises the starting code.
pedal.
► Unlock the steering column by simultaneously
Anti-theft protection
turning the steering wheel and the key.
In certain circumstances, you may have
Electronic immobiliser
to turn the steering wheel firmly to move
The remote control contains an electronic chip
the wheels (if the wheels are against a kerb,
which has a special code. When the ignition is
for example).
switched on, this code must be recognised in
order for starting to be possible.
► Turn the key to position 2, Ignition On, to
A few seconds after switching off the ignition,
activate the engine pre-heating system.
this system locks the engine control system,
► Wait until this warning lamp goes off in
therefore preventing the engine from being
the instrument panel, then turn the key to
started in the event of a break-in.
position 3 without pressing the accelerator pedal,
to operate the starter motor until the engine
134
Driving
starts. As soon as the engine starts, release the
With the Keyless Entry and Start
Never leave the engine running in an
6
key so it returns to position 2.
enclosed area without adequate ventilation:
internal combustion engines emit toxic
The warning lamp does not come on if
exhaust gases, such as carbon monoxide.
the engine is already warm. In some
Danger of poisoning and death!
climatic conditions, the following
recommendations should be followed:
For Diesel vehicles, when the
- In mild conditions, do not leave the engine
► Place the remote control inside the vehicle, in
temperature is below zero,
at idle to warm up but move off straight away
the recognition zone.
starting will only occur once the pre-heating
and drive at moderate speed.
► Press the "START/STOP" button.
warning lamp goes off.
- In wintry conditions, the pre-heater warning
If this warning lamp comes on after pressing
lamp will stay on for a longer period after
The steering column unlocks and the engine
the "START/STOP" button, keep the brake
switching on the ignition; wait until it goes off
starts more or less instantly.
or clutch pedal depressed until the warning
before starting.
- In very severe wintry
The warning lamp does not come on if
lamp goes off, without pressing the "START/
conditions (temperature below -23 °C), to
the engine is already warm. In some
STOP" button again, until the engine starts
ensure correct operation and durability of your
climatic conditions, it is advised to follow the
and is running.
vehicle’s mechanical components (engine
recommendations below:
and gearbox), leave the engine running for
- In mild conditions, do not leave the engine
The "Keyless Entry and Start" system
4 minutes before moving off.
to warm up while stationary, but move off
remote control must be within the
Never leave the engine running in an
straight away and drive at moderate speed.
recognition zone.
enclosed area without adequate ventilation:
- In wintry conditions, when the ignition is
Never leave the vehicle with the engine
internal combustion engines emit toxic
switched on, the duration of lighting of the
running and with the remote control on your
exhaust gases, such as carbon monoxide.
preheating indicator lamp is extended. Wait
person.
Danger of poisoning and death!
until it goes off before starting the engine.
If the remote control leaves the recognition
- In very severe wintry
zone, a message is displayed.
conditions (temperature below -23°C),
Move the remote control into the zone in
If the engine does not start straight away,
to ensure correct operation and preserve
order to be able to start the engine.
switch off the ignition.
the lifespan of the vehicle's mechanical
Wait a few seconds before operating the
starter motor again. If the engine does not
components, engine and gearbox, leave the
If one of the starting conditions is not
start after several attempts, do not keep
engine running for 4 minutes before moving
met, a message is displayed on the
trying: you risk damaging the starter motor
off.
instrument panel. In some circumstances, you
and the engine.
must turn the steering wheel while pressing
135
Driving
the "START/STOP" button to assist unlocking
Avoid attaching heavy objects to the key
- never place one mat on top of another.
of the steering column. A message is
or the remote control, which would weigh
The use of mats not approved by PEUGEOT
displayed.
down on its blade in the ignition switch and
may interfere with access to the pedals and
could cause a malfunction.
hinder the operation of the cruise control /
speed limiter.
Switching off
Key left in the ignition
The mats approved by PEUGEOT have two
fixings located below the seat.
With the conventional key/With the
When opening the driver's door, an alert
remote control key
message is displayed, accompanied by
Starting/Switching off the
► Immobilise the vehicle.
an audible signal, to remind you that the key
► Turn the key all the way to position 1 (Stop)
electric motor
is still in the ignition switch at position 1
and remove it from the ignition.
(Stop).
Starting
► To lock the steering column, turn the steering
If the key has been left in the ignition switch
wheel until it locks.
The drive selector must be in mode P.
at position 2 (Ignition on), the ignition will be
► If using a conventional or remote control
To facilitate unlocking of the steering
switched off automatically after one hour.
key, depress the brake pedal and turn the key
column, it is recommended that the
To switch the ignition back on, turn the key
to position 3 until the motor starts, without
wheels be returned to the straight ahead
to position 1 (Stop), then back to position 2
depressing the accelerator. As soon as the motor
position before switching off the engine.
(Ignition on).
starts, release the key so it returns to position 2.
► If using Keyless Entry and Start, depress the
► Check that the parking brake is correctly
With Keyless Entry and Start
brake pedal and briefly press the "START/STOP"
applied, particularly on sloping ground.
► Immobilise the vehicle.
button.
Never switch off the ignition before the
► Keep your foot on the brake pedal until the
► With the remote control in the recognition
complete immobilisation of the vehicle.
READY indicator lamp comes on and an audible
zone, press the "START/STOP" button.
With the engine off, the braking and steering
signal is emitted, indicating that the vehicle is
The engine stops and the steering column locks.
assistance systems are also turned off: risk of
ready to drive.
loss of control of the vehicle.
If the vehicle is not immobilised, the
► With your foot on the brake, select mode D
engine will not stop.
or R.
As a safety measure, never leave the
► Release the brake pedal, then accelerate.
vehicle without taking the remote control
To avoid any risk of jamming the pedals:
On starting, the instrument panel lights up
with you, even for a short time.
- only use mats which are suited to the
and the power indicator needle performs one
fixings already present in the vehicle; these
sweep then moves to the "neutral" position. The
fixings must be used,
136
Driving
steering column automatically unlocks (you may
► Press this button again to switch off the
Forced switch-off (also called
6
hear a sound and feel the steering wheel move).
ignition and allow the vehicle to be locked.
Back-up switch-off)
Switching off
In case of emergency only, the engine can be
Back-up starting
► If using a conventional or remote control
switched off without conditions (even when
A back-up reader is fitted to the steering column,
key, turn the key fully to position 1 (Stop).
driving).
to enable the engine to be started if the system
► If using Keyless Entry and Start, press the
► To do this, press and hold the "START/
fails to detect the key in the recognition zone, or
"START/STOP" button.
STOP" button for about 5 seconds.
if the battery in the electronic key is flat.
Before exiting the vehicle, check that:
In this case, the steering column locks as soon
- The drive selector is in mode P.
as the vehicle stops.
- The READY indicator lamp is off.
"Key off" mode
The drive selector moves automatically
"Key off" mode allows you to lock the vehicle
to mode P when the motor is switched off
while leaving the engine running without the
or when the driver's door is opened.
key or Keyless Entry and Start being inside the
► Place and hold the remote control against the
vehicle.
If the driver's door is opened while the
back-up reader.
This mode allows electrical devices to continue
required conditions for switching off are
► With a manual gearbox, place the gear lever
operating to ensure thermal comfort, vehicle
not met, an audible signal is emitted,
in neutral, then fully depress the clutch pedal.
security and operation of the vehicle systems
accompanied by the display of a warning
► With an automatic gearbox or a drive
needed for the task.
message.
selector, select mode P, then depress the brake
pedal.
► Press the "START/STOP" button.
Special case with Keyless
The engine starts.
Entry and Start
Remote control not recognised
Switching on the ignition without
If the remote control is no longer in the
KEY
starting the engine
recognition zone, a message appears on the
OFF
instrument panel when closing a door or trying to
With the "Keyless Entry and Start"
switch off the engine.
► To activate or deactivate this mode, press this
electronic key inside the vehicle, pressing
► Press the "START/STOP" button for about
button (the button's indicator lamp is on when
the "START/STOP" button, without depressing
3 seconds to confirm switching off the engine,
the mode is activated).
any of the pedals, allows the ignition to be
then contact a PEUGEOT dealer or a qualified
switched on.
workshop.
137
Driving
With an electric motor, this mode remains
With a manual gearbox, engage a gear
Indicator lamp
active for about 10 minutes after the
and then switch off the ignition.
This indicator lamp comes on both on the
vehicle is locked.
instrument panel and on the control to
With an automatic gearbox, place the
confirm that the parking brake has been applied,
gear selector in position P, then switch
accompanied by display of the message
Manual parking brake
off the ignition.
"Parking brake applied".
The indicator lamp goes out to confirm the
Application
release of the parking brake, accompanied by
Electric parking brake
the display of the message "Parking brake
► With your foot on the brake pedal, pull
released".
the parking brake lever up to immobilise your
In automatic mode, this system applies the
The indicator lamp flashes in response to a
vehicle.
parking brake when the engine is switched off
manual request to apply or release the brake.
and releases it when the vehicle moves off.
Release on level ground
In the event of a battery failure, the
► With your foot on the brake pedal, pull the
electric parking brake will not operate.
parking brake lever up gently, press the release
As a safety measure, with a manual gearbox,
button, then lower the lever fully.
if the parking brake is not applied, immobilise
When the vehicle is being driven, this
the vehicle by engaging a gear.
warning lamp coming on, accompanied
As a safety measure, with an automatic
by an audible signal and a message, indicates
gearbox or drive selector, if the parking brake
that the parking brake is still applied or has not
is not applied, immobilise the vehicle by
been fully released.
placing the supplied chock against one of the
At any time, with the engine running:
wheels.
When parking on a slope or on a steep
► To apply the parking brake, briefly pull the
Contact a PEUGEOT dealer or a qualified
slope with a loaded vehicle, turn the
control.
workshop.
wheels against the kerb then apply the
► To release it, briefly push the control while
parking brake.
pressing the brake pedal.
Automatic mode is activated by default.
Pressing the brake pedal facilitates the
This automatic operation can be deactivated in
application and release of the manual
certain situations.
parking brake.
138
Driving
Before leaving the vehicle, check that the
If the brake pedal is not depressed, the
With an automatic gearbox or drive
6
parking brake is applied: the parking
parking brake is not released and a
selector, if the brake does not release
brake indicator lamps on the instrument panel
message is displayed.
automatically, check that the front doors are
and the control must be on fixed.
properly closed.
If the parking brake is not applied, there is an
Manual application
audible signal and a message is displayed on
When stationary with the engine running,
With the vehicle stationary:
opening the driver's door.
do not depress the accelerator pedal
► Briefly pull the control.
unnecessarily. Risk of parking brake release.
The control indicator lamp flashes to confirm the
Never leave a child alone inside the
application request.
vehicle, as they could release the parking
Automatic application
brake.
Automatic operation
With the vehicle stationary, the parking brake
is applied automatically when the engine is
When the vehicle is parked: on a
Automatic release
switched off.
steep slope, heavily loaded or during
First ensure that the engine is running and that
towing
It is not applied automatically if the
the driver's door is closed.
With a manual gearbox, turn the wheels
engine stalls or enters STOP mode with
The electric parking brake gradually releases
toward the pavement and engage a gear.
Stop & Start.
automatically as the vehicle moves off.
With an automatic gearbox or a drive selector,
With a manual gearbox
turn the wheels toward the pavement and
In automatic mode, the parking brake
► Fully depress the clutch pedal and engage
select mode P.
can be manually applied or released at
first gear or reverse.
When towing, the vehicle is approved for
any time using the control.
► Depress the accelerator pedal and release
parking on slopes of up to 12%.
the clutch pedal.
With an automatic gearbox
Special cases
Manual operation
► Depress the brake pedal.
► Select mode D, M or R.
Immobilising the vehicle with the
Manual release
► Release the brake pedal and depress the
engine running
accelerator pedal.
With the ignition on or engine running:
To immobilise the vehicle with the engine
With a drive selector
► Press the brake pedal.
running, briefly pull the control.
► Depress the brake pedal.
► While maintaining pressure on the brake
► Select mode D, B or R.
pedal, briefly push the control.
► Release the brake pedal and depress the
accelerator pedal.
139
Driving
Parking the vehicle with the brake
Emergency braking
released
If depressing the brake pedal fails to provide
effective braking or in exceptional circumstances
In very cold conditions (ice), applying the
(e.g. driver unwell, assisted driving), the vehicle
parking brake is not recommended.
can be braked by sustained pulling on the
To immobilise the vehicle, engage a gear or
electric parking brake control. Braking continues
place the chocks against one of the wheels.
for as long as the control is kept pulled, and
ceases when the control is released.
With an automatic gearbox or drive
The ABS and DSC systems stabilise the vehicle
selector, mode P is automatically
► Start the engine.
during emergency braking.
selected when the ignition is switched off. The
► Use the control to apply the parking brake, if
If emergency braking malfunctions, the message
wheels are blocked.
it is released.
"Parking brake fault" will be displayed on the
For more information on Free-wheeling, refer
► Take your foot fully off the brake pedal.
instrument panel.
to the corresponding section.
► Keep the control pushed in the release
If the ABS and DSC systems
direction for 10 to a maximum of 15 seconds.
malfunction, indicated by lighting
With an automatic gearbox or a drive
► Release the control.
one or both warning lamps on the instrument
selector, if you open the driver's
► Depress and hold the brake pedal.
panel, the vehicle’s stability is no longer ensured.
door while mode N is engaged, an audible
► Pull the control in the application direction for
► In this case, ensure the vehicle's stability by
signal will sound and mode P will be
2 seconds.
successive and repeated "pull-release" actions
engaged. The audible signal stops when the
This indicator lamp on the instrument
on the electric parking brake control until the
driver's door is closed.
panel comes on to confirm deactivation of
vehicle comes to a complete stop.
the automatic functions.
► Release the control and the brake pedal.
Deactivating automatic
Hill start assist
From this point onwards, only the manual
operation
functions, using the control, allow the parking
This system keeps the vehicle briefly stationary
In some situations, for example when it is
brake to be applied and released.
(for approximately 2 seconds) when making a hill
extremely cold or when towing (e.g. caravan,
► Follow this procedure again to reactivate
start, while you transfer your foot from the brake
breakdown), it may be necessary to deactivate
automatic operation (confirmed by the indicator
pedal to the accelerator pedal.
automatic operation of the system.
lamp on the instrument panel going out).
The system is only active when:
- The vehicle is completely stationary, with your
foot on the brake pedal.
- Certain slope conditions are met.
- The driver’s door is closed.
140
Driving
Do not leave the vehicle while it is being
Facing uphill, with the vehicle stationary,
6-speed manual gearbox
6
held temporarily by hill start assist.
the vehicle is held for a short time when the
If someone needs to get out of the vehicle
driver releases the brake pedal:
Engaging 5th or 6th gear
with the engine running, apply the parking
- If first gear or neutral is engaged on a manual
brake manually. Then check that the parking
gearbox.
► Move the gear selector fully to the right to
brake indicator lamp and the P indicator lamp
- If mode D or M is selected on an automatic
engage 5th or 6th gear.
in the electric parking brake control are on
gearbox.
Failure to follow this instruction could
fixed.
- If mode D or B is selected on the drive
cause permanent damage to the gearbox
selector.
(inadvertent engagement of 3rd or 4th gear).
The hill start assist function cannot be
deactivated. However, using the parking
Engaging reverse gear
brake to immobilise the vehicle interrupts its
operation.
If your vehicle has an automatic gearbox
and you have to move off on a steep
slope (uphill or downhill) with a loaded
Facing downhill, with the vehicle stationary
vehicle, press the brake pedal, select
and reverse gear engaged, the vehicle is held
position D, release the parking brake then
for a short time when the driver releases the
release the brake pedal.
brake pedal.
Malfunction
Operation
If the event of a malfunction, these
warning lamps light up on the
► Raise the ring under the knob and move the
instrument panel, accompanied by the display of
gear lever to the left, then forwards.
a message.
Only engage reverse gear when the
Have it checked by a PEUGEOT dealer or a
vehicle is stationary with the engine at
qualified workshop.
idle.
As a safety precaution and to facilitate
engine starting:
- always select neutral,
141
Driving
- depress the clutch pedal.
The information appears on the
instrument panel, in the form of an "up" or
"down" arrow and the recommended gear.
Gear shift indicator
The system adapts the gear change
(Depending on engine)
instructions according to the driving
This system is designed to reduce fuel
conditions (e.g. slope, load) and driving style
consumption by recommending the most suitable
(e.g. power demand, acceleration, braking).
gear.
The system never suggests:
- engaging first gear.
Operation
- engaging reverse gear.
Depending on the driving situation and
P.
Park.
the vehicle's equipment, the system may
R. Reverse.
recommend skipping one or more gears.
Automatic gearbox
N. Neutral.
Gear engagement recommendations are
D. Drive (automatic operation).
Automatic 6 or 8-speed gearbox, with electronic
not to be considered mandatory. Indeed, the
M. Manual (manual operation with sequential
management of gear changes. It also offers a
configuration of the road, the traffic density and
changing of the gears).
manual mode with sequential gear changes
safety remain determining factors when choosing
via control paddles located behind the steering
the best gear. Therefore, the driver remains
Position N can be used in traffic jams or
wheel.
responsible for deciding whether or not to follow
in a car wash tunnel.
the system’s advice.
Gear selector
The system cannot be deactivated.
On certain BlueHDi Diesel versions with a
To turn the gear selector in complete
manual gearbox, the system may suggest
safety, it is recommended that you keep
shifting into neutral (N is displayed on the
your foot on the brake pedal.
instrument panel) so that the engine can go into
standby (STOP mode of Stop & Start), in certain
driving conditions.
With an automatic gearbox, the system is
only active in manual operation.
142
Driving
Steering mounted controls
When you move the selector or press button M,
If P is displayed on the instrument panel
6
the corresponding gear and indicator lamp are
but the selector is in another position,
shown on the instrument panel.
place the selector in position P to allow the
The "-" symbol is displayed if a value is invalid.
engine to be started.
► If the message "Foot on the brake" is
If position N is selected inadvertently while
displayed on the instrument panel, press
driving, allow the engine to return to idle, then
the brake pedal firmly.
select position D to accelerate.
Starting the vehicle
When the engine is running at idle with
► With your foot on the brake, select
the brakes released, if position R, D or M
position P.
is selected, the vehicle moves even without
► Start the engine.
the accelerator being pressed.
If the conditions are not met, there is an audible
Never leave children inside the vehicle
► Pull the right-hand "+" or left-hand "-" control
signal, accompanied by a message on the
unsupervised.
paddle towards you to change up or down.
instrument panel screen.
As a safety measure, never leave the vehicle
The steering mounted controls do not
► Release the parking brake, unless it is set to
without taking your key or remote control with
allow neutral to be selected and reverse
automatic mode (with electric parking brake).
you, even for a short time.
gear to be engaged or disengaged.
► Select position R, N or D.
When carrying out maintenance with the
engine running, apply the parking brake and
If you are setting off from a steep slope
select position P.
Information displayed on
with a loaded vehicle, depress the
brake pedal, select position D, release the
the instrument panel
With an automatic gearbox, never try to
parking brake, unless it is set to automatic
mode (with electric parking brake), then
start the engine by pushing the vehicle.
release the brake pedal.
Automatic operation
► Gradually release the brake pedal.
Or
► Select position D for automatic
► Accelerate gradually in order to release the
changing of the gears.
electric parking brake (if it is set to automatic
The gearbox then operates in auto-adaptive
mode).
mode, without any intervention on the part of the
The vehicle moves off immediately.
driver. It continuously selects the most suitable
gear according to the driving style, the road
profile and the load in the vehicle.
143
Driving
► For maximum acceleration without
Creeping (moving without
It is only possible to change from one
touching the selector, fully depress the
gear to another if the vehicle speed and
using the accelerator)
accelerator pedal (kick-down).
engine speed permit.
The gearbox changes down automatically or
This function facilitates manoeuvring of the
holds the gear selected until the maximum
vehicle at low speed (when parking, in traffic
If the engine speed is too low or too high,
engine speed is reached.
jams, etc.).
the selected gear flashes for a few
When braking, the gearbox changes down
With the engine at idle, parking brake released
seconds, then the gear actually engaged is
automatically to provide effective engine braking.
and position D, M or R selected, the vehicle
shown.
If you release the accelerator sharply, the
moves as soon as you take your foot off
When the vehicle is stationary or moving very
gearbox will not shift to a higher gear for safety
the brake pedal (even without pressing the
slowly, the gearbox automatically selects gear
reasons.
accelerator).
M1.
Never select position N while the vehicle
As a safety precaution, never leave the
is moving.
vehicle with the engine running and the
To preserve the brakes while descending
Never select positions P or R unless the
doors closed.
a steep incline, use engine braking to
vehicle is completely stationary.
reduce your speed (change down or select a
lower gear).
Manual operation
Keeping the brake pedal pressed
Temporary manual control
► With the selector in position D, press
continuously for long periods can overheat
button M to enable 6- or 8-speed
of gear changes
the brakes, with the risk of damaging the
sequential gear changing.
braking system or making it inoperative.
You can temporarily assume control of gear
The indicator lamp for the button comes on.
Only use the brakes when necessary, to slow
changing using the "+" et "-” steering-mounted
► Operate the "+" or "-" steering mounted
or stop the vehicle.
controls. The gear change request will be
controls.
executed if the engine speed permits.
M appears and the engaged gears are
This function allows you to anticipate certain
Depending on the road configuration
shown in succession on the instrument
situations, such as overtaking another vehicle or
(e.g. mountainous road), manual
panel.
approaching a bend in the road.
operation may be preferable.
► You can revert to automatic operation at any
After a few seconds with no inputs via the control
Automatic operation may not always be
time by pressing button M again.
paddles, the gearbox reverts to automatic
suitable, and does not enable engine braking.
The indicator lamp for the button goes off.
operation.
In manual mode, there is no need to
release the accelerator pedal while
changing gear.
144
Driving
Invalid value during manual
When positioned on a steep slope with a
If your vehicle has an automatic gearbox,
6
loaded vehicle, depress the brake
do not try to start the engine by pushing
operation
pedal, select position P, apply the parking
the vehicle.
This symbol is displayed if a gear is not
brake, unless it is set to automatic mode (with
engaged correctly (gear selector between
electric parking brake), then release the brake
two positions).
pedal.
Drive selector (Electric)
► Place the selector "correctly" at a position.
In all circumstances, ensure that the
Switching off the vehicle
selector is in position P before leaving
Before switching off the engine, select position
your vehicle.
P then apply the parking brake to immobilise
the vehicle, unless this is set to automatic mode
(with electric parking brake).
Malfunction
Check that mode P has been engaged and that
When the ignition is on, a message appears on
the electric parking brake has been applied
the instrument panel to indicate a fault with the
automatically; if not, apply it manually.
gearbox.
The corresponding indicator lamps in the
In this case, the gearbox goes into back-up
selector and the electric parking brake control
mode and is locked in 3rd gear. You may feel a
lever must be on, as well as those on the
significant jolt (without risk to the gearbox) when
The drive selector is a pulse selector with a
instrument panel.
changing from P to R and from N to R.
regenerative braking function.
The drive selector provides traction control
Do not exceed 62 mph (100 km/h), local speed
A point of resistance may be noticed
based on the driving style, the road profile and
restrictions permitting.
when moving to position P.
the vehicle load.
Have it checked by a PEUGEOT dealer or a
If the selector is not in position P, when the
With regenerative braking activated, it also
qualified workshop.
driver's door is opened or approximately 45
manages engine braking when the accelerator
seconds after the ignition is switched off,
There is a risk of damaging the gearbox:
pedal is released.
an audible signal sounds and a message
- If the accelerator and brake pedals are
P. Park
appears.
depressed simultaneously.
Button for parking the vehicle: the front
► Return the drive selector to position P;
- In the event of a battery failure, forcing the
wheels are locked (the button lights up to
the audible signal stops and the message
selector from position P to another position.
indicate that it is activated).
disappears.
R. Reverse
To engage reverse gear, with your foot on the
brake pedal.
145
Driving
N. Neutral
Regenerative braking
With the brake pedal
To move the vehicle with the ignition off and
When the brake pedal is depressed, the
With the Brake function and when
so allow it to free-wheel.
intelligent braking system automatically recovers
decelerating
For more information on Free-wheeling, refer
some of the energy and uses it to recharge the
The Brake function emulates engine braking,
to the corresponding section.
traction battery.
slowing the vehicle with no need to depress the
D. Drive (automatic forward gear)
This energy recovery also reduces use of the
brake pedal. The vehicle slows more quickly
B. Brake (regenerative braking)
brake pads, thereby limiting their wear.
when the driver releases the accelerator pedal.
Regenerative braking (the button lights up to
The energy recovered when the accelerator
The driver may experience a different
indicate its activation).
pedal is released is then used to partially
sensation when depressing the brake
recharge the traction battery, thereby increasing
pedal compared to a vehicle without
Information displayed on
the vehicle's driving range.
regenerative braking.
the instrument panel
The resulting deceleration of the vehicle
When the ignition is switched on, the drive
does not cause the brake lamps to come
selector status is displayed on the instrument
Driving modes (Electric)
on.
panel:
Driving modes are selected using the following
P : Park.
► From mode D, press button B to activate/
control:
R : Reverse.
deactivate the function (the button lights up when
N : Neutral.
the function is activated).
D : Drive (automatic forward gear).
D on the instrument panel is replaced with B.
B : Brake (regenerative braking activated).
The status of the function is saved when the
ignition is switched off.
Operation
In some situations (e.g. battery full,
► Move the selector by pressing it forwards
extreme temperatures), the amount of
(N or R) or rearwards (N or D) once or twice,
regenerative braking may be temporarily
passing the point of resistance if necessary.
limited, resulting in less deceleration.
For example, to change from P to R (with your
The driver must remain alert to traffic
foot on the brake pedal), either push forwards
conditions and must always be ready to use
twice without passing the point of resistance or
► Press the control to display the modes on the
the brake pedal.
push just once, passing the point of resistance.
instrument panel, and depending on version, on
the screen with 3D Connected Navigation.
146
Driving
When starting the vehicle, no mode can be
Primarily designed for urban use, the function
With touch screen
6
selected until the READY indicator lamp is
is intended to reduce fuel consumption and
The settings are changed via the vehicle
displayed.
exhaust emissions as well as the noise level
configuration menu.
When the message disappears, the selected
when stationary.
mode is activated and remains indicated on the
The function does not affect the functionalities of
If the system has been deactivated in
instrument panel (except Normal mode).
the vehicle, in particular the braking.
STOP mode, the engine restarts
Each time the ignition is switched on, Normal
immediately.
Driving on flooded roads
mode is selected by default.
Before entering into a flooded area, it is
Normal
The system is reactivated automatically
strongly recommended that you deactivate
whenever the engine is started by the
This optimises the driving range and dynamic
the Stop & Start system.
driver.
performance.
For more information on Driving
To obtain maximum torque and power, depress
recommendations, particularly on flooded
the accelerator pedal fully.
roads, refer to the corresponding section.
Operation
Eco
Main conditions for operation
Optimises energy consumption, by reducing
Deactivation/Reactivation
- The driver’s door must be closed.
the output of the heating and air conditioning
With audio system
- The sliding side door must be closed.
(without actually deactivating them) and limiting
- The driver's seat belt must be fastened.
both motor torque and power.
- The level of charge in the battery must be
Power
sufficient.
Provides equivalent vehicle performance when
- The temperature of the engine must be within
fully laden (GVW) to when the vehicle is in
its nominal operating range.
Normal mode and when unladen.
- The outside temperature must be between
0°C and 35°C.
Stop & Start
Putting the engine into standby
The Stop & Start function puts the engine
► To deactivate or reactivate the system, press
(STOP mode)
temporarily into standby - STOP mode - during
this button.
The engine automatically enters standby mode
phases when the vehicle is stationary (e.g. red
The indicator lamp is on when the system is
as soon as the driver indicates their intention to
lights, traffic jams). The engine automatically
deactivated.
stop:
restarts - START mode - as soon as the driver
With a manual gearbox: at speeds below 12
indicates the intention of moving off again.
mph (20 km/h) or with the vehicle stationary
147
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст