Peugeot Expert (2022 year). Manual in english — page 8
Driving
(depending on engine), with the gear lever in
Restarting the engine (START mode)
The warning lamp in this button flashes
neutral and the clutch pedal released.
The engine automatically restarts as soon as the
and a message appears, accompanied by
With an automatic gearbox: with the brake
driver indicates the intention of moving off again:
an audible signal.
pedal depressed or the gear selector in
With a manual gearbox: with the clutch pedal
Have it checked by a PEUGEOT dealer or a
position N, with the vehicle stationary.
fully depressed.
qualified workshop.
Time counter
With an automatic gearbox:
The vehicle stalls in STOP mode
- With the selector in position D or M: with the
A time counter adds up the time spent in standby
All of the instrument panel warning lamps come
brake pedal released.
during the journey. It is reset to zero every time
on if there is a fault.
- With the selector in position N and the brake
the ignition is switched on.
Depending on version, a warning message
pedal released: with the selector at D or M.
may also be displayed, prompting you to place
Special cases:
- With the selector in position P and the brake
the gear selector in position N and depress the
pedal depressed: with the selector at R, N, D
The engine will not go into standby if the
brake pedal.
or M.
conditions for operation are not met and in the
► Switch off the ignition then start the engine
- Reverse gear engaged.
following cases:
again with the key or the "START/STOP" button.
- Steep slope (ascending or descending).
Special cases
12 V battery
- Vehicle has not exceeded 6 mph (10 km/h)
The engine will restart automatically if the
The Stop & Start system requires a
since the last engine start (with the key or the
conditions for operation are met again and in the
12 V battery of specific technology and
START/STOP button).
following cases:
specification.
- Needed to maintain a comfortable temperature
- With a manual gearbox: vehicle speed
All work must be carried out only by a
in the passenger compartment.
exceeds 16 mph (25 km/h) or 2 mph (3 km/h)
PEUGEOT dealer or a qualified workshop
- Demisting active.
(depending on engine).
In these cases, this indicator lamp flashes
- With an automatic gearbox, vehicle speed
for a few seconds, then goes off.
exceeds 2 mph (3 km/h).
Tyre under-inflation
After the engine has restarted, STOP
In these cases, this indicator lamp flashes
detection
mode is not available until the vehicle
for a few seconds, then goes off.
has reached a speed of 5 mph (8 km/h).
This system automatically checks the pressures
Malfunctions
of the tyres while driving.
During parking manoeuvres, STOP mode
Depending on the vehicle’s equipment:
It compares the information given by the wheel
is not available for a few seconds after
In the event of a system malfunction, this
speed sensors with reference values, which
coming out of reverse gear or turning the
warning lamp flashes on the instrument
must be reinitialised every time the tyre
steering wheel.
panel.
pressures are adjusted or a wheel changed.
148
Driving
The system triggers an alert as soon as it
Snow chains
Driving too slowly may not ensure
6
detects a drop in the inflation pressure of one or
The system does not have to be
optimum monitoring.
more tyres.
reinitialised after fitting or removing snow
The alert is not immediately triggered in the
chains.
event of a sudden loss of pressure or tyre
Under-inflation detection does not
blow-out. This is because analysis of the
replace the need for vigilance on the part
Spare wheel
values read by the wheel's speed sensors
of the driver.
The steel spare wheel does not have an
can take several minutes.
This system does not avoid the need to
under-inflation detection sensor.
The alert may be delayed at speeds below
regularly check the tyre pressures (including
25 mph (40 km/h), or when adopting a sporty
the spare wheel) as well as before a long
driving mode.
journey.
Under-inflation alert
Driving with under-inflated tyres, particularly
This is signalled by the fixed illumination
The alert is kept active until the system is
in adverse conditions (heavy load, high
of this warning lamp, accompanied by an
reinitialised.
speed, long journey):
audible signal and, depending on equipment, the
- worsens road-holding,
display of a message.
- lengthens braking distances,
► Reduce speed immediately, avoid excessive
Reinitialisation
- causes premature wear of the tyres,
steering movements and avoid sudden braking.
► The system must be reinitialised after any
- increases fuel consumption.
► Stop the vehicle as soon as it is safe to do
adjustment to the pressure of one or more tyres,
so.
and after changing one or more wheels.
The inflation pressures specified for the
vehicle can be found on the tyre pressure
The loss of pressure detected may not
Before reinitialising the system, make
label.
always cause visible deformation of the
sure that the pressures of the four tyres
For more information on the Identification
tyre.
are correct for the conditions of use of the
markings, refer to the corresponding section.
Do not rely on just a visual check.
vehicle and conform to the values written on
the tyre pressure label.
► Using a compressor, such as the one in
Check the pressures of the four tyres before
Checking tyre pressures
the temporary puncture repair kit, check the
performing the reinitialisation.
This check should be done when the
pressures of all four tyres when cold.
The system does not advise if a pressure is
tyres are "cold" (vehicle stopped for 1 hour or
► If it is not possible to carry out this check
incorrect at the time of reinitialisation.
after a journey of less than 6 miles (10 km) at
immediately, drive carefully at reduced speed.
moderate speeds).
► In the event of a puncture, use the
Otherwise, add 0.3 bar to the pressures
temporary puncture repair kit or the spare wheel
shown on the label.
(depending on equipment).
149
Driving
With dashboard button
the whole manoeuvre, in particular using the
Driving and manoeuvring
mirrors.
aids - General
recommendations
Radar(s)
The operation of the radar(s), along with
Driving and manoeuvring aids cannot, in
any associated functions, may be affected
any circumstances, replace the need for
by the accumulation of dirt (e.g. mud, ice),
vigilance on the part of the driver.
in poor weather conditions (e.g. heavy rain,
The driver must comply with the Highway
snow), or if the bumpers are damaged.
► With the vehicle stationary, press this
Code, must remain in control of the vehicle in
If the front bumper is to be repainted, contact
button for about 3 seconds then release it.
all circumstances and must be able to retake
a PEUGEOT dealer or a qualified workshop;
Reinitialisation is confirmed by an audible signal.
control of it at all times. The driver must adapt
certain types of paint could interfere with the
the speed to climatic conditions, traffic and
operation of the radar(s).
Without dashboard button
the state of the road.
With the vehicle stationary, the
It is the driver's responsibility to constantly
system is reinitialised via the
monitor traffic conditions, assess the distance
vehicle configuration menu.
and relative speed of other vehicles, and
anticipate their manoeuvres before using the
Malfunction
direction indicator and changing lanes.
Driving aids camera
In the event of a malfunction,
These systems do not make it possible to
This camera and its associated functions
these warning lamps light up on
exceed the laws of physics.
may be impaired or not work if the windscreen
the instrument panel.
area in front of the camera is dirty, misty,
In this case, the tyre under-inflation monitoring
Driving aids
frosty, covered with snow, damaged or
function is no longer performed.
You should hold the steering wheel with
masked by a sticker.
Have it checked by a PEUGEOT dealer or a
both hands, always use the door and interior
In humid and cold weather, demist the
qualified workshop.
mirrors, always leave your feet close to the
windscreen regularly.
pedals and take a break every 2 hours.
Poor visibility (inadequate street lighting,
heavy rain, thick fog, snowfall), dazzle
Manoeuvring aids
(headlamps of an oncoming vehicle, low sun,
The driver must always check the
reflections on a damp road, leaving a tunnel,
surroundings of the vehicle before and during
alternating shade and light) can also impair
detection performance.
150
Driving
In the event of a windscreen replacement,
always detected by the system: distance
If this is not the case, when the vehicle is
6
contact a PEUGEOT dealer or a qualified
measurements may be distorted.
stationary, set the display to the required
workshop to recalibrate the camera;
The sensors do not systematically detect
units of speed so that it complies with what is
otherwise, the operation of the associated
obstacles that are too low (pavements, studs)
authorised locally.
driving aids may be disrupted.
or too thin (trees, posts, wire fences).
In case of doubt, contact a PEUGEOT dealer
Certain obstacles located in the sensors’ blind
or a qualified workshop.
Other cameras
spots may not be detected or may no longer
The images from the camera(s)
be detected during the manoeuvre.
displayed on the touch screen or on the
Certain materials (fabrics) absorb sound
Head-up display
instrument panel may be distorted by the
waves: pedestrians may not be detected.
System which projects various information onto a
terrain.
smoked blade placed in the driver's field of vision
In the presence of areas in shade, or in
Maintenance
to avoid the driver having to take their eyes off
conditions of bright sunlight or inadequate
Clean the bumpers and door mirrors and
the road.
lighting, the image may be darkened and with
the field of vision of the cameras regularly.
lower contrast.
When washing your vehicle at high pressure,
Display in operation
Obstacles may appear further away than they
direct the spray from at least 30 cm away
actually are.
from the radar, sensors and cameras.
Sensors
Mats/Pedal trims
The operation of the sensors, as well as
The use of mats or pedal trims not
any associated functions, may be disrupted
approved by PEUGEOT may interfere with
by noise pollution such as that emitted by
the operation of the speed limiter or cruise
noisy vehicles and machinery (e.g. lorries,
control.
pneumatic drills), by the accumulation of
To avoid any risk of jamming the pedals:
snow or dead leaves on the road or in the
- Ensure that the mat is secured correctly.
event of damaged bumpers and mirrors.
- Never fit one mat on top of another.
When reverse gear is engaged, an audible
Once the system has been activated, the
signal (long beep) indicates that the sensors
Units of speed
following information is grouped together in the
may be dirty.
Ensure that the units of speed displayed
head-up display:
A front or rear impact to the vehicle can
on the instrument panel (mph or km/h) are
A. The speed of the vehicle.
upset the sensors’ settings, which is not
those for the country you are driving in.
B. Cruise control/speed limiter information.
151
Driving
C. If the vehicle is so equipped, inter-vehicle
Activation/Deactivation
When stationary or while driving, no
distance information, automatic emergency
► With the engine running, press button 1 to
objects should be placed around the
braking alerts and navigation instructions.
activate the system and deploy the projection
projection blade (or in its recess) so as not to
D. If the vehicle is so equipped, speed limit
blade.
impede its movement and correct operation.
information.
In certain extreme weather conditions
For more information about Navigation,
(rain and/or snow, bright sunshine, etc.),
refer to the sections describing the audio
the head-up display may not be legible or
and telematics systems.
may suffer temporary interference.
Some sunglasses may hamper reading of the
information.
Selectors
To clean the projection blade, use a clean,
soft cloth (such as a spectacles cloth or
microfibre cloth). Do not use a dry or abrasive
cloth, or detergent or solvent products, due to
the risk of scratching the projection blade or
► Press and hold button 2 to deactivate the
damaging the non-reflective coating.
system and retract the projection blade.
The state of the system is saved when the
engine is switched off and restored on restarting.
This system operates when the engine is
running, and the settings are saved when
Adjusting the height
the ignition is switched off.
► With the engine running, adjust the display to
the desired height using the buttons 4:
• up to move the display up,
Memorising speeds
• down to move the display down.
This function allows you to save speed
1.
On.
settings which are then used to set the two
2.
Off (long press).
Brightness adjustment
systems: the speed limiter (limits the speed
3.
Brightness adjustment.
► With the engine running, adjust the
of the vehicle) or cruise control (vehicle
4.
Display height adjustment.
brightness of the information display using the
cruising speed).
buttons 3:
You can save 6 speed settings for each of the
• on the "sun" to increase the brightness,
two systems.
• on the "moon" to decrease the brightness.
152
Driving
Programming
Road signs recognition
instrument panel must match that of the
6
country you are driving in.
The speed thresholds can be set in the
vehicle configuration menu using the
For more information, refer to the
touch screen.
General recommendations on the use
Automatic sign reading is a driving aid
► Select the system for which you want to
of driving and manoeuvring aids.
system and does not always display the
memorise new speed settings:
correct speed limits.
- speed limiter
The speed limit signs present on the road
always take priority over those displayed by
or
the system.
- cruise control.
The system is designed to detect signs that
conform to the Vienna Convention on road
signs.
Activation/Deactivation
This system displays the maximum speed
The settings are changed via the
authorised locally on the instrument panel, using:
vehicle configuration menu.
- Speed limit signs detected by the camera.
- Speed limit information from the navigation
Information displayed on
system’s mapping.
the instrument panel
Navigation mapping should be regularly
updated in order to receive accurate
► Press the button corresponding to the speed
speed limit information from the system.
setting you want to change.
► Enter the new value using the numerical
The units for the speed limit (mph or
keypad and confirm.
km/h) depend on the country you are
► Confirm to record the changes and quit the
driving in.
menu.
This should be taken into account to ensure
Memorised speeds are recalled
you observe the speed limit.
by pressing this button.
For the system to work properly when
changing countries, the speed unit of the
153
Driving
Head-up display
Storing the speed setting
The driver can, if desired, adjust the
speed of the vehicle according to the
In addition to Road signs recognition, the
information given by the system.
driver can select the speed displayed as a speed
setting for the speed limiter or cruise control
Operating limits
using the speed limiter or cruise control 'store'
The system does not take account of reduced
button.
speed limits, especially those imposed in the
following cases:
For more information on the Speed
1. Speed limit indication
- Poor weather (rain, snow).
limiter, Cruise control or Adaptive
- Atmospheric pollution.
cruise control, refer to the corresponding
Speed display
- Towing.
sections.
- Driving with a space-saver type spare wheel
or snow chains fitted.
Steering-mounted controls
- Tyre repaired using the temporary puncture
repair kit.
- Young drivers.
The system may not display the speed limit if it
The system is active but is not detecting speed
does not detect a speed limit sign within a preset
limit information.
period and in the following situations:
- Road signs that are obstructed, non-standard,
damaged or bent.
1. Speed limiter/cruise control mode selection
- Obsolete or incorrect maps.
2. Memorise the speed setting
On detection of speed limit information, the
system displays the value.
154
Driving
Information displayed on the
Storing the speed setting
Speed limiter
6
instrument panel
For more information, refer to the
General recommendations on the use
of driving and manoeuvring aids.
► Switch on the speed limiter/cruise control.
This system prevents the vehicle from
The speed limiter/cruise control information is
exceeding the speed programmed by the
displayed.
driver (speed setting).
Upon detecting a sign suggesting a new speed
The speed limiter is switched on manually.
setting, the system displays the value and
The minimum speed setting is 19 mph (30 km/h).
"MEM" flashes for a few seconds, prompting you
The speed setting remains in the system
to save it as a new speed setting.
memory when the ignition is switched off.
Head-up display
If there is a difference of less than 6 mph
For more information on this
(9 km/h) between the speed setting and
button and the Adaptive cruise
the speed displayed by the Road signs
control, refer to the corresponding section.
recognition, the "MEM" symbol is not
displayed.
For more information on
Memorising speeds, refer to the
Depending on the road conditions, several
corresponding section.
speeds may be displayed.
► Press button 2 once to save the suggested
For more information on Speed limit
speed value.
recognition and memorising the speed
A message is displayed, confirming the request.
limit in particular, refer to the corresponding
► Press button 2 again to confirm and save the
3. Speed limit indication.
section.
new speed setting.
4. Request to memorise the speed.
The display then reverts to its previous state.
5. Current speed setting.
155
Driving
Steering-mounted control
For more information on Memorising speeds
Switching on/Pausing
or the Road signs recognition, refer to the
► Turn thumbwheel 1 to the "LIMIT" position
corresponding sections.
to select speed limiter mode; the function is
paused.
Information displayed on
► If the speed limit setting is suitable (most
the instrument panel
recent speed setting programmed in the system),
press button 4-II to switch the speed limiter on.
► Pressing 4-II again temporarily pauses the
function (pause).
Adjusting the limit speed
setting
You do not have to switch the speed limiter on in
order to set the speed.
To modify the limit speed setting based on the
Head-up display
vehicle’s current speed:
1.
ON (LIMIT position)/OFF (position 0)
► For steps of +/- 1 mph (1 km/h), briefly
2.
Reduce the speed setting
press 2-SET- or 3-SET+ repeatedly.
3.
Increase the speed setting
► For steps of +/- 5 mph (5 km/h), press and
4.
Pause/resume speed limiter with the speed
hold 2-SET- or 3-SET+.
setting previously stored
To change the limit speed setting using
5.
Depending on version:
memorised speeds, via the touch screen:
Display the speed thresholds saved using the
► Press 5-MEM to display the memorised
Memorising speeds function
speed settings.
or
► Press the touch screen button for the desired
Use the speed suggested by the Road signs
speed setting.
recognition function (MEM display)
The selection screen closes after a few
6.
Display and adjustment of the programmed
7.
Speed limiter on/pause indication.
moments.
inter-vehicle distance
8.
Speed limiter mode selection indication.
This setting becomes the new limit speed.
9.
Speed setting value.
To modify the speed limit setting based on the
speed suggested by the Road signs recognition
function displayed on the instrument panel:
156
Driving
► Press 5-MEM once; a message is displayed,
Malfunction
Exceeding the programmed speed
6
confirming the memorisation request.
setting
► Press 5-MEM again to save the suggested
You can temporarily exceed the speed
speed.
setting by pressing the accelerator pedal (the
The new speed setting value is displayed on the
programmed speed flashes).
In the event of a malfunction, dashes are
instrument panel.
To return to the speed setting, release the
displayed flashing and then fixed instead of the
accelerator pedal (when the set speed is
speed setting.
Temporarily exceeding the
reached again, the displayed speed stops
Have it checked by a PEUGEOT dealer or a
flashing).
programmed speed
qualified workshop.
► To temporarily exceed the programmed
Operating limits
speed threshold, fully depress the accelerator
Cruise control - Specific
Never use the system in the following
pedal.
recommendations
situations:
The speed limiter is deactivated temporarily and
- In an urban area with the risk of
the displayed programmed speed flashes.
The cruise control function does not
pedestrians crossing the road.
If it is exceeded for a prolonged period of time,
guarantee compliance with the maximum
- In heavy traffic.
an audible warning is triggered.
authorised speed and the safety distance
- On winding or steep roads.
Simply release the accelerator pedal to return to
between vehicles, the driver remains
- On slippery or flooded roads.
below the programmed speed.
responsible for their driving.
- In poor weather conditions.
When the limit speed is exceeded but this is not
In the interest of public safety, only use cruise
- In the event of restricted visibility for the
due to action by the driver (in case of a steep
control if the traffic conditions enable vehicles
driver.
slope, for example), an audible signal triggers
to drive at a steady speed and maintain an
- Driving on a speed circuit.
immediately.
adequate safety distance.
- Driving on a rolling road.
Once the speed of the vehicle returns to the
Remain vigilant while cruise control is
- When using snow chains, non-slip covers
programmed setting, the speed limiter functions
activated. If you press and hold one of the
or studded tyres.
again: the display of the programmed speed
speed setting modification buttons, your
setting becomes fixed again.
vehicle may change speed very abruptly.
Switching off
When descending a steep hill, the cruise
Cruise control
control system cannot prevent the vehicle
► Turn the thumbwheel 1 to the "0" position:
from exceeding the set speed. Brake if
For more information, refer to the
the display of information on the speed limiter
necessary to control the vehicle speed.
General recommendations on the use
disappears.
On steep climbs or when towing, the set
of driving and manoeuvring aids and the
speed may not be reached or maintained.
157
Driving
Cruise control - Specific
Steering-mounted control
Information displayed on
recommendations.
the instrument panel
This system automatically maintains the
vehicle’s speed at the value programmed
by the driver (speed setting), without the use of
the accelerator pedal.
Cruise control is switched on manually.
It requires a minimum vehicle speed of 25 mph
(40 km/h).
With a manual gearbox, third gear or higher must
be engaged.
1.
ON (CRUISE position)/OFF (position 0)
With an automatic gearbox, mode D or second
Head-up display
2.
Activate cruise control at the current speed/
gear or higher in mode M must be engaged.
decrease speed setting
With a drive selector, mode D or B must be
3.
Activate cruise control at the current speed/
engaged.
increase speed setting
Cruise control remains active after
4.
Pause/resume cruise control with the speed
changing gear, regardless of the gearbox
setting previously saved
type, on engines fitted with the Stop & Start
5.
Depending on version:
function.
Display the speed thresholds saved using the
Memorising speeds function
Switching off the ignition cancels any
or
speed setting.
Use the speed suggested by the Road signs
recognition function (MEM display)
6. Cruise control pause/resume indication.
For more information on Memorising speeds
7. Cruise control mode selection indication.
or the Road signs recognition, refer to the
8. Speed setting value.
corresponding sections.
Switching on/pausing
► Turn thumbwheel 1 to the "CRUISE" position
to select cruise control mode; the function is
paused.
158
Driving
► Press button 2-SET- or 3-SET+ to activate
As a precaution, we recommend setting
To return to the programmed speed, simply
6
cruise control and save a speed setting when
a cruise speed fairly close to the current
release the accelerator pedal.
the vehicle has reached the desired speed; the
speed of your vehicle, to avoid any sudden
Once the vehicle has returned to the
vehicle’s current speed is saved as the speed
acceleration or deceleration of the vehicle.
programmed speed, cruise control takes over
setting.
again and the programmed speed setting stops
To change the cruise speed setting using
► Release the accelerator pedal.
flashing.
memorised speed settings and from the touch
► Pressing button 4-II temporarily pauses the
screen:
When descending a steep hill, the cruise
function (pause).
► Press 5-MEM to display the memorised
control system cannot prevent the
► Pressing button 4-II again resumes operation
speed settings.
vehicle from exceeding the programmed
of the cruise control (ON).
► Press the touch screen button for the desired
speed.
Cruise control can also be paused
speed setting.
You may have to brake to control the speed of
temporarily:
The selection screen closes after a few
your vehicle. In this case, the cruise control is
- by pressing the brake pedal.
moments.
automatically paused.
- by pressing the clutch pedal with a manual
This setting becomes the new cruise speed.
To activate the system again, with the vehicle
gearbox (depending on the engine fitted).
To change the cruise speed setting using the
speed above 25 mph (40 km/h), press button
- automatically, if the electronic stability
speed suggested by the Road signs recognition
4.
control (ESC) system is triggered.
function displayed on the instrument panel:
► Press 5-MEM once; a message is displayed,
Switching off
confirming the memorisation request.
Changing the cruise speed
► Turn the thumbwheel 1 to the "0” position: the
► Press 5-MEM again to save the suggested
setting
cruise control information disappears from the
speed.
screen.
The cruise control must be active.
The new speed setting value is displayed on the
To change the cruise speed setting, based on
instrument panel.
Malfunction
the vehicle’s current speed:
► For steps of +/- 1 mph (1 km/h), briefly
Temporarily exceeding the
press 2-SET- or 3-SET+ repeatedly.
programmed speed
► For steps of +/- 5 mph (5 km/h), press and
If needed (when overtaking, for example),
In the event of a malfunction, dashes are
hold 2-SET- or 3-SET+.
it is possible to exceed the programmed
displayed flashing and then fixed instead of the
Pressing and holding 2-SET- or 3-SET+
speed by pressing the accelerator pedal.
speed setting.
results in a rapid change in the speed of
Cruise control is temporarily deactivated and the
Have it checked by a PEUGEOT dealer or a
the vehicle.
programmed speed displayed flashes.
qualified workshop.
159
Driving
Adaptive cruise control
overtaking manoeuvre, without ever
5. Depending on version:
exceeding the speed setting.
Display the speed thresholds saved using the
Refer to the General recommendations
Memorising speeds function
on the use of driving and
Some vehicles present on the road may
or
manoeuvring aids and to Cruise control
not be properly seen or may be
Use the speed suggested by the Road signs
- particular recommendations.
misinterpreted by the radar (e.g. a lorry),
recognition function (MEM display)
which may lead to a poor assessment of
6. Display and adjustment of the distance
This system automatically maintains the
distance and lead to the vehicle accelerating
setting to the vehicle in front
speed of your vehicle at a value which
or braking inappropriately.
you set (speed setting), while keeping a safe
Use
distance from the vehicle in front (target vehicle),
and which has been set beforehand by the
Steering-mounted controls
Activating the system (paused)
driver. The system controls the vehicle's
The adaptive cruise control must be selected in
acceleration and deceleration automatically
the "Driving/Vehicle" menu.
using only engine braking (as if the driver had
► Turn the knob 1 downwards into the CRUISE
pressed the "-" minus button).
position with the engine running. The cruise
control is ready for operation.
Starting cruise control and selecting a
speed
The vehicle speed must be between 25 and
To do this, it uses a radar located in the front
93 mph (40 and 150 km/h).
bumper.
1.
ON (CRUISE position)/OFF (position 0)
With a manual gearbox, third or fourth gear or
Primarily designed for driving on main
2.
Activation of cruise control at the current
higher must be engaged.
roads and motorways, this system only
speed/decrease speed setting
With an automatic gearbox, mode D or second
works with moving vehicles driving in the
3.
Activation of cruise control at the current
gear or higher in mode M must be engaged.
same direction as your vehicle.
speed/increase speed setting
With a drive selector, mode D or B must be
4.
Pause/resume cruise control with the speed
engaged.
If the driver operates a direction indicator
setting previously saved
If the speed setting is above 93 mph
to overtake a slower vehicle, the cruise
(150 km/h), the adaptive cruise control
control allows the vehicle to temporarily
switches to standard cruise control mode
approach the vehicle in front to assist the
160
Driving
(without automatic regulation of the inter-
paused, the message "Activation not possible,
Information displayed on
6
vehicle safety distance).
unsuitable conditions" is briefly displayed if
the instrument panel
reactivation is not possible (safety conditions
► Press buttons 2-SET- or 3-SET+: the current
not met).
speed becomes the speed setting (minimum
25 mph (40 km/h)) and the cruise control is
Using the Road signs recognition function
immediately activated.
or speed limit sign memorisation to
► Press 3 to increase or 2 to decrease the
modify the speed setting.
speed setting (in steps of 5 mph (5 km/h) if the
► Press 5-MEM to accept the speed setting
button is kept depressed).
proposed by the system on the instrument panel
Pressing and holding either button
or touch screen, then press again to confirm.
2-SET- or 3-SET+ results in a rapid
To prevent any sudden acceleration or
change in the speed of the vehicle.
deceleration of the vehicle, select a
Head-up display
speed setting fairly close to the current speed
Pausing/resuming cruise control
of your vehicle.
► Press 4-II or depress the brake pedal. To
pause cruise control, it is also possible to:
Changing the inter-vehicle distance
• Shift from mode D to N,
► Press 6 to display the distance setting
• Depress the clutch pedal for more than 10
thresholds ("Distant", "Normal" or "Close"), then
seconds.
press again to select a threshold.
• Press the electric parking brake control.
After a few seconds, the option is accepted and
► Press 4-II to restart cruise control. Cruise
will be memorised when the ignition is switched
control may have been paused automatically:
off.
• When the inter-vehicle distance threshold is
reached.
Temporarily exceeding the speed setting
• When the distance between your vehicle and
► Depress the accelerator pedal. Distance
7.
Cruise control pause/resume indication.
the one in front becomes too short.
monitoring and cruise control are deactivated as
8.
Indication of selection of cruise control mode,
• When the vehicle starts moving too slowly or
long as you continue to accelerate. The speed
or vehicle speed adjustment phase.
the vehicle in front starts moving too slowly.
on the instrument panel flashes.
9.
Speed setting value.
• When the ESC system is triggered.
Deactivating the system
When the driver attempts to reactivate
► Turn the knob 1 upwards into position 0
cruise control, after the function has been
(OFF).
161
Driving
For more information on the Head-up
Above this, the system pauses itself if the safety
display, refer to the corresponding
distance becomes too short.
section.
The adaptive cruise control uses only engine
braking to slow the vehicle. Consequently the
vehicle loses speed slowly, as when releasing
Messages and alerts
the accelerator pedal.
- Vehicles not running in the middle of the lane.
The system is paused automatically:
The display of these messages or alerts
- if the vehicle in front slows down too much or
is not sequential.
too suddenly, and the driver does not brake,
“Cruise control paused” or “Cruise control
- if a vehicle comes between your vehicle and
suspended” following a brief acceleration
the vehicle in front,
by the driver.
- if the system does not slow the vehicle enough
“Cruise control active”, no vehicle
to continue to maintain a safe distance, for
detected.
example when descending a steep hill.
“Cruise control active”, vehicle detected.
Cases of non-detection by the radar:
- Vehicles entering a corner.
- Stationary vehicles (traffic jam, breakdown,
- Vehicles changing lane at the last moment.
“Cruise control active and speed
etc.).
Reactivate cruise control when conditions permit.
adjusted”, vehicle detected too close or at
- Vehicles driving in the opposite direction.
Cases where the driver is urged to take back
a slower speed.
When the driver must suspend the cruise
control immediately:
“Cruise control active and speed
control system:
- When a vehicle cuts in sharply between your
adjusted”, automatic deactivation
vehicle and the one in front.
imminent following a cruise control limit being
- Excessively sharp deceleration of the vehicle
reached.
in front of you.
“Cruise control paused”, automatic
The adaptive cruise control operates by
deactivation following speed limit
day and night, in fog or moderate rainfall.
adjustment being exceeded and no reaction from
the driver.
- When following a narrow vehicle.
The system does not act on the braking
Operating limits
system, but works only with engine
braking.
The regulation range is limited to a maximum
The regulation range is limited: there will
difference of 19 mph (30 km/h) between the
no longer be any adjustment of speed if the
cruise speed setting and the speed of the
difference between the programmed speed
vehicle in front.
162
Driving
setting and the speed of the vehicle in front
This system:
6
becomes too great.
- warns the driver that their vehicle is at risk of
collision with the preceding vehicle.
If the difference between the
- reduces the vehicle's speed to avoid a
programmed speed setting and the
collision or to limit its severity.
speed of the vehicle in front is too great, the
The speed will be reduced by a
speed cannot be adjusted: the cruise control
maximum of 16 mph (25 km/h) (versions
is automatically deactivated.
with camera only) or by a maximum of 31
mph (50 km/h) (versions with camera and
radar).
Malfunction
The vehicle has a camera located at the top of
In the event of a malfunction with the adaptive
The system also takes motorcyclists into
the windscreen and, depending on version, a
cruise control, you will be alerted by an audible
account.
radar located in the front bumper.
signal and the display of the message "Driving
It may also react on animals. Animals
aid functions fault".
This system does not replace the need
(especially animals smaller than 0.5 m)
Have it checked by a PEUGEOT dealer or a
for vigilance on the part of the driver.
and objects on the road are not necessarily
qualified workshop.
This system is designed to assist the driver
detected.
and improve road safety.
It is the driver's responsibility to continuously
Active Safety Brake with
This system includes three functions:
monitor traffic conditions in accordance with
- Collision Risk Alert.
Collision Risk Alert and
applicable driving regulations.
- Intelligent emergency braking assistance
Intelligent emergency
(iEBA).
- Active Safety Brake (automatic emergency
As soon as the system detects a
braking assistance
braking).
potential obstacle, it prepares the braking
circuit in case automatic braking is needed.
For more information, refer to the
This may cause a slight noise and a slight
General recommendations on the use
sensation of deceleration.
of driving and manoeuvring aids.
Operating conditions and
limits
Vehicle moving forward without trailer.
163
Driving
Brake system operational.
(e.g. sensor initialization, board voltage out of
The last threshold selected is memorised when
Seat belts fastened for all passengers.
regular range, activation of stability system).
the ignition is switched off.
Stabilised speed on roads with no or low
Therefore, the system may not be available
curvature.
just after starting the vehicle.
Operation
This warning lamp lights up on the
Depending on the collision risk detected by the
instrument panel without any additional
It can be dangerous to drive if the brake
system and the alert trigger threshold chosen
message, to indicate that the automatic braking
lamps are not in perfect working order.
by the driver, different levels of alert may be
system is not available.
triggered and displayed on the instrument panel.
This is a normal behavior indicating that a
The system takes into account the vehicle
The driver must not overload the vehicle
condition is not fulfilled and which does not
dynamics, the difference speed of the own
(keep within the GVW limit and load
request the support of a workshop.
vehicle and the object identified for the
height limits for roof bars).
In any situations with ignition on where automatic
collision risk, and the operation of the vehicle
braking presents a risk, deactivating the
(e.g. actions on the pedals, steering wheel) to
Following an impact (e.g. a collision), the
system via the vehicle's configuration menu is
trigger the alert at the most relevant moment.
system is automatically deactivated.
recommended, for instance:
(orange)
Have it checked by a PEUGEOT dealer or a
- Towing a trailer (particularly a trailer without its
Level 1: visual alert only, warning that the
qualified workshop.
own braking system).
preceding vehicle is very close.
- Carrying long objects on roof bars or roof rack.
The message "Vehicle close" is displayed.
- Driving with snow chains.
Collision Risk Alert
(red)
- Using an automatic car wash.
Level 2: visual and audible alert, warning
This function warns the driver if there is a risk
- Performing any maintenance (e.g. changing a
that a collision is imminent.
of collision with the preceding vehicle, or with a
wheel, working inside the engine compartment).
The message "Brake!" is displayed.
pedestrian or cyclist.
- Placing the vehicle on a rolling bench in a
While approaching a vehicle too quickly,
workshop.
Modifying the alert trigger threshold
the level 2 alert may be displayed
- Towing the vehicle.
This trigger threshold determines the sensitivity
directly.
- Following a front bumper deformation.
with which the function warns of the risk of
Important: the level 1 alert depends on the
- Following an impact to the windscreen close to
collision.
trigger threshold selected. It reacts only on
the detection camera.
The threshold is set via the vehicle
moving vehicles. It is disabled automatically
The system diagnoses permanently its
configuration menu with the audio
at lower speed.
capability and may inhibit itself without
system or touch screen.
specific driver indication, if the system is
► Select one of the three pre-defined
outside of the regular operating conditions
thresholds: "Far", "Normal" or "Close".
164
Driving
It is possible that collision warnings are
Active Safety Brake
Operation
6
not given, are given too late or seem
The system operates subject to the following
unjustified.
conditions:
The driver must always stay in control of the
- At reduced speed in an urban environment,
vehicle and be prepared to react at any time
when a stationary vehicle, pedestrian or cyclist
to avoid an accident.
is detected.
- The vehicle's speed is between 6 mph and
53 mph (10 km/h and 85 km/h) (versions with
Intelligent emergency
camera only) or 87 mph (140 km/h) (versions
braking assistance (iEBA)
with camera and radar) when a moving vehicle
This function supplements braking in the event
is detected.
that the driver brakes, but not enough to avoid a
This warning lamp flashes (for
collision.
approximately 10 seconds) as soon as
This assistance will only be provided if the driver
the function applies the vehicle’s brakes.
presses the brake pedal.
During the flashing time, the function is not
available.
With an automatic gearbox, in the event of
automatic emergency braking, keep the brake
This function, also called "automatic emergency
pedal depressed, also after a complete stop is
braking", intervenes after the acoustic alert if the
reached, to prevent the vehicle from rolling away.
driver does not operate the brake pedal quickly
With a manual gearbox, in the event of automatic
enough.
emergency braking bringing the vehicle to a
The system aims at reducing the speed of
complete stop, the engine may stall.
impact or avoiding a collision if the driver fails to
react.
The driver can override the automatic
emergency braking at any time by firmly
The speed will be reduced by a
turning the steering wheel and/or firmly
maximum of 16 mph (25 km/h) (versions
depressing the accelerator pedal.
with camera only) or by a maximum of 31
mph (50 km/h) (versions with camera and
radar).
165
Driving
The brake pedal may feel hard and
accompanied by the display of a message and
If the direction indicator is not used at speeds
vibrate slightly while the function is
an audible signal.
above 50 mph (80 km/h) and there is a risk of
operating.
Have it checked by a PEUGEOT dealer or a
one of these lines on the road surface being
If the vehicle comes to a complete stop,
qualified workshop.
crossed, the system triggers the alert.
automatic braking is maintained for 1 to 2
If these warning lamps come on after the
This system is particularly useful on motorways
seconds.
engine has been switched off and then
and main roads.
restarted, contact a PEUGEOT dealer or a
qualified workshop to have the system checked.
Detection - Alert
Deactivation/Activation
These warning lamps light up on
You are alerted by the flashing of this
By default, the system is automatically activated
the instrument panel and/or in the
warning lamp in the instrument panel,
at every engine start.
warning lamp display for seat belts and front
accompanied by an audible signal.
The settings are changed via the
passenger airbag to indicate that the driver's
vehicle configuration menu.
No warning is transmitted while the
and/or front passenger's seat belt is not fastened
Deactivation of the system is signalled by
direction indicator is active and for
(depending on version). The automatic braking
the illumination of this warning lamp,
approximately 20 seconds after the direction
system is deactivated until the seat belts are
accompanied by the display of a message.
indicator is switched off.
fastened.
Malfunction
Activation/Deactivation
Lane departure warning
This warning lamp lights up on the
instrument panel with the message
system
With audio system
"Sensor blind" in certain cases.
Version with camera only: the system is
For more information, refer to the
deactivated.
General recommendations on the use
Version with camera and radar: the system
of driving and manoeuvring aids.
may continue to operate in a degraded mode.
This may be caused by a reduced visibility
(e.g. rain, fog, snow, blinding by low sun) or by
a real sensor blockage. In this case, stop the
vehicle and verify if the front camera or the front
► To activate or deactivate the system, press
radar is covered by dirt, snow, ice or anything
System that uses a camera to recognise
this button.
preventing the sensing.
continuous or broken lines on traffic lanes and
The indicator lamp is on when the system is
In the event of a malfunction, this warning
triggers an alert if the vehicle wanders off line.
activated.
lamp lights up on the instrument panel,
166
Driving
With touch screen
alone or combined with the "Driver Attention
- The ignition has been switched off for a few
6
The settings are changed via the vehicle
Warning by Camera" system.
minutes.
configuration menu.
- The driver's seat belt is unfastened and their
These systems are in no way designed
door is opened.
to keep the driver awake or to prevent
Malfunction
the driver from falling asleep at the wheel.
As soon as the speed of the vehicle
Depending on the vehicle’s equipment:
It is the driver’s responsibility to stop if feeling
drops below 43 mph (70 km/h), the
The indicator lamp in this button flashes.
tired.
system goes into standby.
Take a break if you are feeling tired or at least
Driving time starts being counted again once
or
every 2 hours.
the speed reaches above 43 mph (70 km/h).
/
The button flashes and a fault
appears.
Consult a PEUGEOT dealer or a qualified
Activation/Deactivation
Driver Attention Warning by
workshop.
This function is set via the vehicle
Camera
configuration menu.
Detection may be impeded:
Depending on version, the Driver Attention
The function is activated by default when the
- If the markings on the ground are worn
Warning system may be combined with the
ignition is switched on.
and not clearly contrasted against the road
Driver Attention Warning by Camera system.
surface.
Driver Attention Warning
- If the windscreen is dirty.
The system triggers an alert when it
- In certain extreme weather conditions:
detects that the driver has not taken a
fog, heavy rain, snow, shade, bright sunlight
break after two hours of driving at a speed above
or direct exposure to the sun (e.g. low sun,
43 mph (70 km/h).
leaving a tunnel).
This alert is issued via the display of a message
encouraging the driver to take a break,
accompanied by an audible signal.
Distraction detection
If the driver does not follow this advice, the alert
is repeated hourly until the vehicle is stopped.
For more information, refer to the
The system resets itself if one of the following
General recommendations on the use
The system assesses the driver's level of
conditions is met:
of driving and manoeuvring aids.
alertness, fatigue and distraction by
- With the engine running, the vehicle has been
identifying trajectory changes in relation to the
Depending on version, the function consists of
stationary for more than 15 minutes.
lane markings.
either the "Driver Attention Warning" system
167
Driving
To do this, the system uses a camera, placed on
The alert is given by an orange warning lamp
the upper part of the windscreen.
coming on in the relevant door mirror, as soon as
This system is particularly suited to fast roads
a vehicle - car, lorry, bicycle - is detected.
(speed higher than 43 mph (70 km/h)).
The following conditions must be met for this:
At a first alert level, the driver is warned by the
- all vehicles are moving in the same direction
message "Be vigilant!", accompanied by an
and in adjacent lanes,
audible signal.
- the speed of your vehicle must be between 7
After three first-level alerts, the system triggers
and 87 mph (12 and 140 km/h),
a further alert with the message "Dangerous
- you overtake a vehicle with a speed difference
This system warns the driver of a potential
driving: take a break", accompanied by a more
of less than 6 mph (10 km/h),
danger posed by the presence of another vehicle
pronounced audible signal.
- a vehicle overtakes you with a speed
(car, lorry, motorcycle) in the vehicle's blind
difference of less than 16 mph (25 km/h),
In certain driving conditions (poor road
spots (areas hidden from the driver's field of
- the traffic is flowing normally,
surface or strong winds), the system may
vision) using sensors located on the sides of the
- overtaking a vehicle over a certain period of
give alerts independent of the driver's level of
bumpers.
time where the vehicle being overtaken remains
vigilance.
in the blind spot,
- you are driving on a straight or slightly curved
The following situations may interfere
road,
with the operation of the system or
- your vehicle is not towing a trailer, a caravan,
prevent it from working:
etc.
- lane markings absent, worn, hidden (snow,
mud) or multiple (roadworks);
- close to the vehicle ahead (lane markings
A warning lamp appears in the door mirror on the
not detected);
side in question:
- roads that are narrow, winding, etc.
- fixed, immediately, when being overtaken;
- flashing, after a delay of about one second,
when overtaking a vehicle slowly, and when the
Blind spot monitoring
direction indicator is used.
For more information, refer to the
Operation
General recommendations on the use
Sensors fitted in the front and rear bumpers
of driving and manoeuvring aids.
monitor the blind spots.
168
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст