Peugeot Partner (2022 year). Manual in english — page 9
Driving
Manoeuvre cancelled or finished (red)
Interruption by the driver:
End of the parking space entry or exit
6
(the arrows indicate that the driver must
- taking over control of the steering.
manoeuvre
resume control of the vehicle).
- activating the direction indicator lamps on the
The vehicle stops as soon as the manoeuvre is
The maximum speeds during manoeuvres are
opposite side to that of the manoeuvre.
completed.
indicated by these symbols:
- unfastening the driver's seat belt.
The manoeuvre symbol is displayed in red,
5 mph or 7 km/h, for parking space entry.
- switching off the ignition.
accompanied by the message "Manoeuvre
7
Interruption by the system:
completed" on the touch screen.
3 mph or 5 km/h, for parking space exit.
- vehicle exceeding the speed limit of
When the function is deactivated, this
5
5 mph (7 km/h) during parking space entry
indicator lamp goes off, accompanied by
manoeuvres, or 3 mph (5 km/h) during parking
During manoeuvring phases, the steering
an audible signal.
space exit manoeuvres.
wheel performs rapid turns: do not hold
When entering a parking space, the driver may
- activation of anti-slip regulation on a slippery
the steering wheel or put your hands between
be required to complete the manoeuvre.
road.
the spokes of the steering wheel. Watch out
- opening of a door or the boot.
Operating limits
for any objects that could interfere with the
- engine stall.
manoeuvre (loose clothing, scarf, tie, etc.).
- The system may suggest an inappropriate
- system malfunction.
Risk of injury!
parking space (parking prohibited, work in
- after 10 manoeuvres to enter or exit a parallel
It is the driver's responsibility to constantly
progress with damaged road surface, location
parking space and after 7 manoeuvres to enter a
monitor the traffic, especially vehicles coming
alongside a ditch, etc.).
parking bay.
towards you.
- The system may indicate that a space has
Interrupting the manoeuvre automatically
The driver should check that no objects or
been found but will not offer it because of a fixed
deactivates the function.
people are obstructing the vehicle’s path.
obstacle on the opposite side of the manoeuvre,
The manoeuvre symbol is displayed in red,
which would not allow the vehicle to follow a
accompanied by the "Manoeuvre cancelled"
trajectory required for parking.
The images from the camera(s)
message on the touch screen.
- The system may indicate that a space has
displayed on the touch screen may be
A message prompts the driver to take back
been found but the manoeuvre will not be
distorted by the terrain.
control of the vehicle.
triggered, because the width of the lane is
In shady areas, or in inadequate sunlight
The function is deactivated after a few
insufficient.
or lighting conditions, the image may be
seconds; this indicator lamp goes off and
- The system is not designed for performing the
darkened and with lower contrast.
the function returns to the initial display.
parking manoeuvre on a sharp bend.
The manoeuvre can be permanently interrupted
- The system does not detect spaces that
at any time, either by the driver or automatically
are much larger than the vehicle itself or that
by the system.
are delimited by obstacles that are too low
169
Driving
(pavements, studs, etc.) or too thin (trees, posts,
- If the sensors have been repainted other
wire fences, etc.).
than by the PEUGEOT dealer network.
- If the boot is heavily loaded, the tilt of the
- With sensors not approved for the vehicle.
vehicle towards the rear may interfere with the
distance measurements.
Malfunctions
Do not use the function under the
When the function is not activated, this
following exterior conditions:
indicator lamp will flash briefly and an
- Alongside a soft shoulder (e.g. ditch) or
audible signal will be emitted to indicate a
quay or on the edge of a drop.
system malfunction.
- When the road surface is slippery (e.g. ice).
If the malfunction occurs while the system is in
use, the indicator lamp goes off.
If any of the following malfunctions
If the parking sensor malfunction occurs
occurs, do not use the system:
during use, indicated by this warning lamp
- If a tyre is under-inflated.
coming on, it causes the function to deactivate.
- If one of the bumpers is damaged.
Consult a PEUGEOT dealer or a qualified
- If one of the cameras is faulty.
workshop.
In the event of a power steering
If the vehicle has undergone any of the
malfunction, this warning lamp is
following modifications, do not use the
displayed on the instrument panel, accompanied
function:
by a warning message.
- When carrying an object extending beyond
You must stop the vehicle.
the dimensions of the vehicle (ladder on the
Stop as soon as it is safe to do so and
roof bars, bicycle carrier on the tailgate, etc.).
switch off the ignition.
- With a non-approved towball in place.
Contact a PEUGEOT dealer or a qualified
- With snow chains fitted.
workshop.
- When driving on a small-diameter or
"space-saver" type spare wheel.
- When the wheels fitted are a different size
from the original ones.
- After modifying one or both bumpers
(added protection).
170
PEUGEOT & TOTAL
PARTNERS IN PERFORMANCE!
For over 25 years, the PEUGEOT TOTAL partnership has pushed the boundaries
of performance to achieve success in the most difficult of conditions, with
victories in the Le Mans 24 Hours, in the Dakar Rally and also those by all
of our Rally customers around the world. To obtain these exceptional results,
the Peugeot Sport teams chose TOTAL QUARTZ, a high-tech lubricant that
protects the engine in the most extreme conditions.
TOTAL QUARTZ protects your engine against the
effects of tim e.
TOTAL QUARTZ INEO XTRA FIRST 0W-20 is a very high-performance
lubricant developed jointly by the Peugeot and Total R&D teams.
Specially formulated for the engines in Peugeot vehicles, its innovative
technology significantly reduces CO2 emissions and effectively protects your
engine against clogging.
Practical information
fuels could prevent the engine from operating
signal are repeated with increasing frequency as
Compatibility of fuels
correctly. In these temperature conditions, use
the fuel level drops towards 0.
winter-type Diesel fuel and keep the fuel tank
You must refuel as soon as possible to avoid
more than 50 % full.
running out of fuel.
Petrol fuels conforming to the EN228 standard
At temperatures below -15 °C (+5 °F) to avoid
For more information on Running out of fuel
containing up to 5% and 10% ethanol
problems starting, it is best to park the vehicle
(Diesel), refer to the corresponding section.
respectively.
under shelter (heated garage).
A small arrow by the warning lamp
indicates which side of the vehicle the
Travelling abroad
fuel filler flap is located on.
Diesel fuels conforming to the EN590, EN16734
Certain fuels could damage your vehicle’s
and EN16709 standards and containing up to
engine.
Stop & Start
7%, 10%, 20% and 30% fatty acid methyl ester
In certain countries, the use of a particular
Never refuel with the engine in STOP
respectively. The use of B20 or B30 fuels, even
fuel may be required (specific octane rating,
mode; you must switch off the ignition.
occasionally, imposes special maintenance
specific trade name, etc.) to ensure correct
conditions referred to as "Arduous conditions".
operation of the engine.
For all additional information, consult a dealer.
Refuelling
At least 10 litres of fuel must be added, in order
Paraffinic Diesel fuel conforming to the EN15940
Refuelling
to be registered by the fuel gauge.
standard.
Opening the filler cap may create a noise caused
Fuel tank capacity: approximately 61 litres
by an inrush of air. This is entirely normal and
The use of any other type of (bio)fuel
(Petrol) or 50 litres (Diesel).
results from the sealing of the fuel system.
(e.g. pure or diluted vegetable or animal
Reserve level: approximately 6 litres.
To refuel in complete safety:
oils, domestic fuel) is strictly prohibited - risk
► Always switch off the engine.
of damaging the engine and fuel system!
Low fuel level
► Unlock the vehicle using the Keyless Entry
1
When the low fuel level is reached,
1/2
and Start.
The only fuel additives authorised for use
this warning lamp lights up on the
► Open the fuel filler flap.
are those that meet the B715001 (petrol)
instrument panel, accompanied by the display of
or B715000 (Diesel) standards.
a message and an audible signal. When it first
comes on, about 6 litres of fuel remain.
Until sufficient fuel is added, this warning lamp
Diesel at low temperature
appears every time the ignition is switched on,
At temperatures below 0 °C (+32 °F), the
accompanied by the message and the audible
formation of paraffins in summer-type Diesel
signal. When driving, this message and audible
172
Practical information
► Put the filler cap back in place and close it by
If the fuel filler flap is open, a device
7
turning to the right.
prevents the left-hand side door from
► Push the fuel filler flap to close it (your
opening.
vehicle must be unlocked).
The door can be opened half-way, however.
Close the fuel filler flap to regain use of the
door.
The vehicle is fitted with a catalytic converter,
which helps to reduce the level of harmful
emissions in the exhaust gases.
If you have put in the wrong fuel for
► With a conventional key, insert the key into
your vehicle, you must have the fuel
the filler cap, then turn the key to the left.
tank drained and filled with the correct fuel
before starting the engine.
If the vehicle is equipped with a sliding
door on its left-hand side, do not open it
Fuel cut-off
while the fuel filler flap is open. Otherwise,
Your vehicle is fitted with a safety system that
there is a risk that the fuel filler flap and the
cuts off the supply of fuel in the event of an
sliding door may be damaged and the person
impact.
filling up may be injured.
Misfuel prevention (Diesel)
(Depending on country of sale.)
This mechanical device prevents filling the tank
► Unscrew and remove the filler cap, then
If the fuel filler flap is open, a device
of a Diesel vehicle with petrol.
place it on the holder located on the fuel filler
prevents the left-hand side door from
Located in the filler neck, the misfuel prevention
flap.
opening.
device is visible when the filler cap is removed.
► Insert the nozzle and push it in fully (while
The door can be opened half-way, however.
pushing on the metal valve A).
Close the fuel filler flap to regain use of the
► Fill the tank. Do not continue past the
door.
third cut-off of the nozzle, as this may cause
malfunctions.
173
Practical information
Operation
- Never work on the orange high voltage
Charging system
cables or on any other high voltage
(Electric)
component marked with the Electric risk label.
Any intervention on the high voltage system
400 V electrical system
must be carried out by qualified persons in
workshops qualified and approved to carry
The electric drive system, which operates at a
out this type of work.
voltage of approximately 400 V, is identified by
- Never damage, modify or remove the
orange cables and its components are marked
orange high voltage cables or disconnect
with this symbol:
them from the high voltage network.
- Never open, modify or remove the cover of
the traction battery.
- Never work with cutting and forming
When a petrol filler nozzle is introduced into the
tools or heat sources near high voltage
fuel filler neck of a Diesel vehicle, it comes into
components and cables.
contact with the flap. The system remains closed
In case of low level of fluid in the cooling
and prevents filling.
An electric vehicle’s power train can
tank, the refilling shall only be performed in a
Do not persist but introduce a Diesel type
become hot during use and after
qualified and trained workshop to verify that
filler nozzle.
switching off the ignition.
the leakage is not in the traction battery.
Comply with the warning messages shown
The misfuel prevention device does not
Any intervention on the high voltage system
on the labels, particularly inside the charging
prevent filling with a jerrycan, regardless
must be carried out by qualified persons in
flap.
of the fuel type.
workshops qualified and approved to carry
out this type of work.
High voltage system voltage is
Damage to the vehicle or the traction battery
Travelling abroad
dangerous and can cause burns or other
could result in the leakage of toxic gases or
As Diesel fuel pump nozzles may be
injuries or even fatal electric shock.
fluids either immediately or later. PEUGEOT
different in other countries, the presence
Since damage to high voltage components is
recommends that you:
of the misfuel prevention device may make
not visible, PEUGEOT recommends that you:
- Always inform the fire and emergency
refuelling impossible.
- Never touch the components, damaged
services in the event of an incident, warning
Before travelling abroad, it is advisable to
or not, and never let your jewelry or other
that the vehicle is equipped with a traction
check with a PEUGEOT dealer if the vehicle
metallic objects come into contact with these
battery.
is suitable for the distribution equipment of the
components.
- Never touch the liquids leaking from the
countries visited.
traction battery.
174
Practical information
- Do not inhale the gases emitted by the
When washing
thermal comfort equipment and the ageing of its
7
traction battery which are toxic.
Before washing the vehicle, always
components.
- Move away from the vehicle in the event of
check that the charging flap is closed
The lifespan of the traction battery
incident or accident, the gases emitted being
correctly.
depends on multiple factors, such as
flammable and could cause a fire.
Never wash the vehicle while the battery is
climatic conditions, distance travelled and
on charge.
how often it has been fast-charged.
High-pressure washing
To preserve the mileage of your vehicle
To avoid damaging the electrical
and the durability of your traction battery,
components, it is expressly prohibited to
PEUGEOT recommends that you:
use high-pressure washing in the engine
- Do not fully charge the battery of your
compartment or under the body.
electric vehicle daily (charge the traction
Do not use a pressure greater than 80 bar
battery below 80% as often as possible).
when washing the bodywork.
- Do not completely discharge the battery.
- Do not store the vehicle for a long period
This label is intended solely for use by
Never allow water or dust to enter the
of non-use (more than 12 hours) when the
firefighters and maintenance services in
connector or charging nozzle - risk of
traction battery has a low or high charge level.
the event of any work on the vehicle.
electrocution or fire!
Prefer a charge level between 20 and 40%.
No other person must touch the device shown
Never connect / disconnect the charging
- Limit the use of fast charging.
on this label.
nozzle or cable with wet hands - risk of
- Do not expose the vehicle to temperatures
electrocution!
below -30°C and above +60°C for more than
In the event of an accident or impact
24 hours.
to the vehicle’s underbody
- Avoid charging the vehicle at negative
Traction battery
In these situations, the electrical circuit or the
temperatures (except if the vehicle ran more
traction battery can be seriously damaged.
This battery stores the energy that powers
than 20 minutes) or above +30°C.
Stop as soon as it is safe to do so and switch
the electric motor and the thermal comfort
- Do not use the vehicle's traction battery as
off the ignition.
equipment in the passenger compartment. It is
a generator of energy.
Contact a PEUGEOT dealer or a qualified
discharged during use, and must therefore be
- Do not use a generator to recharge your
workshop.
regularly recharged. There is no need to wait
vehicle's traction battery.
for the traction battery to fall to its reserve level
before recharging.
The range of the battery may vary according
to the type of driving, the route, the use of
175
Practical information
In the event of damage to the traction
Charging connectors and
State of charging
Meaning
battery
indicator lamps
indicator lamp
It is strictly prohibited to work on the vehicle
yourself.
Fixed white
Welcome lighting on
Do not touch liquids coming from the battery,
opening the flap and
and in the event of skin contact with these
disconnecting the
products, wash abundantly with water and
charging cable.
contact a doctor as soon as possible.
Fixed blue
Deferred charging.
Contact a PEUGEOT dealer or a qualified
workshop to have the system checked.
Flashing green
Charging.
Fixed green
Charging complete.
The charging
Disposal of the traction battery
indicator lamp goes
The traction battery is designed for the life of the
off after about 2
vehicle if the recommendations of PEUGEOT
minutes as the
are followed.
vehicle's functions go
If it becomes necessary to replace the battery,
1.
Charging connectors
into standby.
contact the PEUGEOT dealer for instructions on
2.
Deferred charging activation button
The indicator lamp
its disposal. Improper disposal carries the risk of
3.
Nozzle locking indicator lamp
comes on again
severe burns, electric shock, and damage to the
Fixed red: nozzle positioned correctly and
when the vehicle is
environment.
locked in the connector.
unlocked with the
In accordance with regulations, PEUGEOT
Flashing red: nozzle incorrectly positioned or
Keyless Entry and
ensures a second life or recycling of this
locking not possible.
Start system or when
component in collaboration with qualified
4.
Charging indicator lamp
a door is opened
operators.
to indicate that
the battery is fully
charged.
Fixed red
Malfunction.
176
Practical information
In case of impact, even light, against the
travelling abroad, check the compatibility of local
7
charging flap, do not use it.
electrical systems with the charging cable.
Do not dismantle or modify the charging
A full range of charging cables is available from
connector - risk of electrocution and/or fire!
your dealer.
Contact a PEUGEOT dealer or a qualified
Contact a PEUGEOT dealer or a qualified
workshop.
workshop for more information and to obtain
suitable charging cables.
Charging cables, sockets
Identification labels on charging
and chargers
sockets/connectors
The charging cable supplied with the vehicle
Identification labels are affixed to the vehicle,
(depending on version) is compatible with the
charging cable and charger to inform the user
The meaning of each identification label is as
electrical systems in the country of sale. When
about which device needs to be used.
follows:
Identification label
Location
Configuration
Power type/Voltage range
Charging connector (vehicle side)
TYPE 2
AC
C
< 480 Vrms
Charging socket (charger side)
TYPE 2
AC
C
< 480 Vrms
Charging connector (vehicle side)
COMBO 2 (FF)
DC
K
50 V - 500 V
177
Practical information
Standard charging, mode 2
Specific domestic charging cable
If the indicator lamp does not go off, contact a
(mode 2)
PEUGEOT dealer or a qualified workshop.
Domestic socket
You must not damage the cable.
Upon plugging the charging cable into a
(standard charging - alternating current (AC))
In the event of damage, do not use it and
domestic socket, all of the indicator lamps come
contact a PEUGEOT dealer or a qualified
on briefly.
workshop to replace it.
If no indicator lamps come on, check the
domestic socket's circuit-breaker:
Control unit (mode 2)
- If the circuit-breaker has tripped, contact a
professional to check that the electrical system
Mode 2 with a standard socket: 8 A maximum
is compatible and/or carry out any necessary
charging current.
repairs.
- If the circuit-breaker has not tripped, stop
using the charging cable and contact a
PEUGEOT dealer or a qualified workshop.
Control unit label - Recommendations
Mode 2 with a Green'Up socket: 16 A
Refer to the handbook before use.
maximum charging current.
To have this type of socket installed, call a
professional installer.
Specific domestic charging cable - mode
POWER
2 (AC)
Green: electrical connection established;
charging can begin.
1.
Incorrect use of this charging cable may
CHARGE
result in fire, property damage and serious
Flashing green: charging in progress or
injury or death by electrocution!
temperature pre-conditioning activated.
2.
Always use a correctly earthed power
Fixed green: charging complete.
socket, protected by a 30 mA residual
FAULT
current device.
Red: fault; charging not permitted or must
3.
Always use an electrical socket protected
be stopped immediately. Check that everything
by a circuit-breaker appropriate for the
Identification label C on the charging
is connected correctly and that the electrical
electrical circuit’s current rating.
connector (vehicle side).
system is not faulty.
178
Practical information
4.
The weight of the control unit must not be
9.
Do not unplug the plug from the wall as a
Control unit label - State of indicator
7
borne by the electrical socket, plug and
means of stopping charging.
lamps
cables.
10.
Immediately stop charging, by locking and
State of the
5.
Never use this charging cable if it is
then unlocking the vehicle using the remote
indicator lamp
defective or in any way damaged.
control key, if the charging cable or wall
6.
Never attempt to repair or open this
socket feel burning hot to the touch.
Off
charging cable. It contains no repairable
11.
This charging cable includes components
parts - replace the charging cable if it is
liable to cause electrical arcing or sparks.
damaged.
Do not expose to flammable vapours.
On
7.
Never immerse this charging cable in water.
12.
Only use this charging cable with PEUGEOT
8.
Never use this charging cable with an
vehicles.
Flashing
extension cable, a multi-plug socket, a
13.
Never plug the cable into the wall socket (or
conversion adaptor or on a damaged
unplug it) with wet hands.
electrical socket.
14.
Do not force the connector if it is locked into
the vehicle.
POWER
CHARGE
FAULT
Symbol
Description
Not connected to the power supply or power is not
available from the infrastructure.
The control unit is currently performing a self-test.
(green)
(green)
(red)
Connected only to the infrastructure or to the
infrastructure and to the Electric Vehicle (EV) but
no charging in progress.
(green)
179
Practical information
POWER
CHARGE
FAULT
Symbol
Description
Connected to the power supply and to the Electric
Vehicle (EV).
The EV is on charge or in a temperature pre-
(green)
(green)
conditioning sequence.
Connected to the power supply and to the Electric
Vehicle (EV).
The EV is waiting for charging or the charging of
(green)
(green)
the EV is completed.
Control unit malfunction. No charging allowed.
If an error indicator reappears after a manual reset,
the control unit must be checked by a PEUGEOT
(red)
dealer before the next charge.
The control unit is in diagnostic mode.
(green)
(green)
(red)
Manual reset procedure
The control unit can be reset by simultaneously disconnecting the charging connector and the wall socket.
Then, reconnect the wall socket first. For more information, refer to the handbook.
180
Practical information
Accelerated charging, mode 3
Superfast charging, mode 4
Charging cable, mode 3 (AC)
7
Accelerated charging unit (depending on
Fast public charger
version)
(superfast charging - direct current (DC))
(accelerated charging - single-phase or three-
phase alternating current (AC))
In mode 3 with an accelerated charging unit:
32 A maximum charging current.
Charging cable, mode 4 (DC)
(integrated into the fast public charger)
Identification labels C on the charging
connector (vehicle side) and on the socket
(charger side).
Accelerated charging unit
In mode 3 with an accelerated charging unit
Do not disassemble or modify the
Identification label K on the charging
(Wallbox): 32 A maximum charging current.
charging unit - risk of electrocution and/or fire!
connector (vehicle side).
Refer to the charging unit manufacturer's user
Only use fast public chargers where the cable
manual for the operating instructions.
length does not exceed 30 metres.
Charging the traction
battery (Electric)
To recharge, connect the vehicle to a domestic
electricity supply (domestic or accelerated
charging) or to a fast public charger (superfast
charging).
181
Practical information
For a full charge, follow the desired charging
accidents or serious injuries. ALWAYS make
about every 3 months in order to recharge the
procedure without pausing it, until it ends
sure the traction battery has a sufficient
accessory battery and maintain an operating
automatically. Charging can be either immediate
charge level.
voltage.
or deferred (except fast public charger, mode 4).
You can stop domestic or accelerated charging
Low load / Parking
Precautions
at any time by unlocking the vehicle and
If the outside temperature is negative,
removing the nozzle. For superfast charging,
Our electric vehicles have been developed in
it is recommended not to park your vehicle
refer to the fast public charger.
accordance with the recommendations on the
outside for several hours at a low load (less
For more information on the charging displays
maximum limits for electromagnetic fields, as
than 20%).
on the Instrument panel and the Touch screen,
issued by the International Commission on Non-
refer to the corresponding section.
Ionizing Radiation Protection (ICNIRP - 1998
Vehicle in storage for more than
Guidelines).
It is also possible to monitor the charging
1 month
Wearers of pacemakers or equivalent
progress using the MYPEUGEOT APP
In the event of a long period of non-use of
devices
application.
the vehicle (beyond 4 weeks) without the
For more information on Remote functions,
possibility of charging when restarting, the
Ask your doctor about what precautions
refer to the corresponding section.
self-discharge may make it impossible to
you should take, or ask the manufacturer
restart if the traction battery charge level
of your implanted electro-medical device about
is a low or very low, especially at negative
whether its operation is guaranteed in an
As a safety measure, the engine will not
ambient temperatures. ALWAYS make sure
environment which complies with the ICNIRP
start if the charging cable is plugged into
that the traction battery has a charge between
recommendations.
the connector on the vehicle. A warning is
20% and 40% if you do not plan to use your
displayed on the instrument panel.
If in doubt
vehicle for several weeks.
Domestic or accelerated charging: do
Do not connect the charging cable.
Cooling the traction battery
not remain inside or near the vehicle, or near
Always park the vehicle in a place with
The cooling fan in the engine
the charging cable or charging unit, even for
temperatures between -10°C and 30°C
compartment comes on during charging to
a short time.
(parking in a place with extreme temperatures
cool the on-board charger and the traction
Superfast charging: do not use the system
can damage the traction battery).
battery.
yourself and avoid approaching public fast
Disconnect the cable from the (+) terminal
charging points. Leave the area and ask a
of the accessory battery in the engine
third party to recharge the vehicle.
Low load / Driving
compartment.
Driving when the charge level of the
Connect a 12 V battery charger to the (+)
traction battery is too low can lead to the
and (-) terminals of the accessory battery
vehicle breaking down and can lead to
182
Practical information
For domestic or accelerated charging
Do not leave the cable connected to the
Domestic charging, mode 2
7
domestic power socket - risk of short-circuit
Before charging
or electrocution in the event of contact with or
Depending on the context:
immersion in water!
► Have a professional check that the
electrical system to be used complies with
applicable standards and is compatible with
For superfast charging
the vehicle.
Before charging
► Have a professional electrician install
Check that the fast public charging
a dedicated domestic power socket or
station and its charging cable are compatible
accelerated charging unit (Wallbox)
with the vehicle.
compatible with the vehicle.
If the exterior temperature is below:
You should preferably use the charging cable
- 0°C, charging times may be extended.
available as an accessory.
- -20°C, charging is still possible, but
For more information, contact a PEUGEOT
charging times may be extended even further
► Connect the charging cable from the control
dealer or a qualified workshop.
(the battery has to be heated first).
unit to the domestic socket.
When the connection is made, all of the indicator
During charging
lamps on the control unit light up, then only the
After charging
While charging is in progress, unlocking
POWER indicator lamp remains on in green.
Check that the charging flap is closed.
the vehicle will cause the charging to stop.
► Remove the protective cover from the
If no action is taken on one of the openings
charging nozzle.
(door or boot) or on the charging nozzle, the
Connection
► Insert the nozzle into the charging connector.
vehicle will lock again after 30 seconds and
► Before charging, check that the drive selector
The start of charging is confirmed by the flashing
charging will resume automatically.
is in mode P, otherwise charging is not possible.
green CHARGE indicator lamps in the flap, then
Never work under the bonnet:
► Open the charging flap by pressing the
those on the control unit.
- Some areas remain very hot, even an hour
push-button, and check that there are no foreign
If this is not the case, charging has not
after charging ends - risk of burns!
bodies on the charging connector.
started; restart the procedure, ensuring that all
- The fan may start at any time - risk of cuts
connections are properly established.
or strangulation!
The red indicator lamp in the flap comes on to
indicate that the nozzle is locked.
After charging
When charging is complete and while the
Check that the charging flap is closed.
charging cable is still connected, opening
183
Practical information
the driver's door will display the charge level
► Follow the instructions for use of the fast
In the vehicle, with PEUGEOT Connect
on the instrument panel for about 20 seconds.
public charger and connect the cable from the
Nav
fast public charger to the vehicle's connector.
► In the Energy touch screen menu,
Accelerated charging, mode 3
The start of charging is confirmed by the flashing
select the Charge page.
green charging indicator lamp in the flap.
► Set the charging start time.
If this is not the case, charging has not started;
► Press OK.
restart the procedure, ensuring that the
The setting is saved in the system.
connection is properly established.
Activation
The red indicator lamp in the flap comes on to
indicate that the nozzle is locked.
Deferred charging is only possible with
modes 2 and 3.
► Follow the accelerated charging unit
Deferred charging
(Wallbox) user instructions.
► After programming the deferred charging,
Settings
► Remove the protective cover from the
connect your vehicle to the desired charging
charging nozzle.
At a PEUGEOT dealer or qualified
equipment.
► Insert the nozzle into the charging connector.
workshop, with touch screen BLUETOOTH
The start of charging is confirmed when the
audio system
charging indicator lamp in the flap flashes green.
By default, the deferred charging start time is set
If this is not the case, charging has not started;
to midnight (vehicle time).
restart the procedure, ensuring that the
You can have the deferred charging start time
connection has been properly established.
modified.
The red indicator lamp in the flap comes on to
Go to a PEUGEOT dealer or a qualified
indicate that the nozzle is locked.
workshop.
► Press this button in the flap within one
Superfast charging, mode 4
On a smartphone or tablet
minute to activate the system (confirmed by the
You can programme the deferred
charging indicator lamp coming on in blue).
charging function at any time via the
► Lock the vehicle.
MYPEUGEOT APP application.
For more information on Remote functions,
refer to the corresponding section.
► Depending on version, remove the protective
cover from the lower part of the connector.
184
Practical information
Disconnection
Domestic charging, mode 2
disconnected before full charging was
7
completed.
The end of charging is confirmed when the green
CHARGE indicator lamp on the control unit and
the green charging indicator lamp in the flap
come on fixed.
Energy economy mode
► Replace the protective cover on the charging
This system manages the duration of use of
nozzle and close the charging flap.
Before disconnecting the nozzle from the
certain functions, in order to conserve a sufficient
► Disconnect the control unit end of the
charging connector:
level of charge in the battery with the ignition off.
charging cable from the domestic socket.
► If the vehicle is unlocked, lock it and then
After switching off the engine and for a maximum
unlock it.
Accelerated charging, mode 3
cumulative period of around 30 minutes, you can
► If the vehicle is locked, unlock it.
The end of charging is indicated by the charging
continue to use functions such as the audio and
The red indicator lamp in the flap goes out to
control unit and by the fixed lighting of the green
telematics system, dipped beam headlamps or
confirm that the charging nozzle is unlocked.
indicator lamp in the flap.
courtesy lamps.
► In modes 2 and 3, remove the charging
► Hang up the nozzle on the charging unit and
nozzle within 30 seconds.
close the charging flap.
Selecting the mode
A confirmation message is displayed when
Superfast charging, mode 4
energy economy mode is entered, and the active
The end of charging is indicated by the charger
functions are placed on standby.
and by the fixed lighting of the green indicator
The locking of the nozzle is linked to the
lamp in the flap.
If a telephone call is in progress at the
locking of the loading area. For more
► You can also pause charging by
time, it will be maintained for around 10
information on Complete or selective
pressing this button in the flap (in mode 4
minutes via the audio system’s hands-free
unlocking, refer to the corresponding
only).
system.
section.
► Hang up the nozzle on the charger.
The charging indicator lamp comes on in white.
► Depending on version, replace the protective
Exiting the mode
cover on the lower section and close the
With selective door unlocking activated,
These functions are automatically reactivated the
charging flap.
press the unlocking button twice to
next time the vehicle is used.
disconnect the charging nozzle.
When the charging nozzle is
To restore the use of these functions
disconnected, a message on the
immediately, start the engine and let it run:
When charging is complete, the green
instrument panel indicates that charging is
- For less than 10 minutes, to use the
charging indicator lamp in the flap goes
complete, even if the charging nozzle was
equipment for approximately 5 minutes.
out after about 2 minutes.
185
Practical information
- For more than 10 minutes, to use the
Observe the legislation in force in your
It is strongly recommended that you
equipment for approximately 30 minutes.
country relating to the use of snow
practise fitting the snow chains on a level
Let the engine run for the specified duration to
chains and maximum authorised speeds.
and dry surface before setting off.
ensure that the battery charge is sufficient.
Use only the chains designed to be fitted to the
To recharge the battery, avoid repeatedly or
Avoid driving with snow chains on roads
type of wheel fitted to your vehicle:
continuously restarting the engine.
that have been cleared of snow to avoid
Original tyre size
Link size: (mm)
damaging the vehicle's tyres and the road
A flat battery prevents the engine from
surface. If the vehicle is fitted with alloy
starting.
195/65 R15
9
wheels, check that no part of the chain or its
For more information on the 12 V battery,
205/60 R16
fixings is in contact with the wheel rim.
refer to the corresponding section.
205/55 R17
215/65 R16
Very cold climate screen
Load reduction mode
215/60 R17
Cannot be fitted with
(Depending on country of sale)
This system manages the use of certain
chains
This removable device prevents the
functions according to the level of charge
You can also use snow socks.
accumulation of snow around the radiator
remaining in the battery.
For more information, contact a PEUGEOT
cooling fan.
When the vehicle is being driven, the load
dealer or a qualified workshop.
reduction function temporarily deactivates certain
functions, such as the air conditioning and the
Installation tips
heated rear screen.
► To fit the snow chains during a journey, stop
The deactivated functions are reactivated
the vehicle on a flat surface at the side of the
automatically as soon as conditions permit.
road.
► Apply the parking brake and position any
Snow chains
wheel chocks under the wheels to prevent
movement of the vehicle.
In wintry conditions, snow chains improve
► Fit the snow chains following the instructions
traction as well as the behaviour of the vehicle
provided by the manufacturer.
when braking.
► Move off gently and drive for a few moments,
Snow chains must be fitted only to the
without exceeding 31 mph (50 km/h).
front wheels. They must never be fitted to
► Stop the vehicle and check that the snow
"space-saver" type spare wheels.
chains are correctly tightened.
186
Practical information
Fitting
Removing
7
In case of difficulty with installation/
removal
► Hold the screen in front of the lower grille of
► Insert a finger into the notch in the upper part
Contact a PEUGEOT dealer or a qualified
the bumper.
of the screen.
workshop.
► First insert the upper and side fixing brackets
► Pull towards you to unclip the unit.
into the bumper.
Before any operation, ensure that the
► Tilt the screen downwards to engage the
engine is off and the cooling fan has
Towing device
lower part of the screen into the bumper.
stopped.
► Check that the unit is firmly held by pressing
Depending on version, the vehicle is
around the edges.
fitted with the necessary equipment to
It is essential to remove them when:
allow a towing device to be installed.
- the outside temperature exceeds
To install a towing device, contact a
10°C.
PEUGEOT dealer or a qualified workshop.
- recovery is in progress.
- the speed is above 75 mph (120 km/h).
Load distribution
► Distribute the load in the trailer so that the
heaviest items are as close as possible to the
187
Practical information
axle, and the nose weight approaches the
- Do not transport more than 4 conventional
Even if you correctly measure the weight
maximum permitted without exceeding it.
bicycles or 2 electric bicycles.
of the vehicle's load, any factor that may
Air density decreases with altitude, thus reducing
When loading bicycles onto a bicycle carrier
vary this weight (driver/additional passengers
engine performance. The maximum towable load
on a towball, be sure to place the heaviest
seated or taking on additional fuel) after the
must be reduced by 10% per 1,000 metres of
bicycles as close as possible to the vehicle.
measurement may put the vehicle into the
altitude.
overload condition.
Observe the legislation in force in the
Use genuine towing devices and wiring
country where you are driving.
harnesses approved by PEUGEOT. We
recommend having them fitted by a
PEUGEOT dealer or a qualified workshop.
Electric motor
If not fitted by a PEUGEOT dealer, they must
An electric vehicle may be fitted with a
still be fitted in accordance with the vehicle
towing device.
manufacturer's instructions.
It is therefore possible to tow a trailer or
Certain driving or manoeuvring aid functions
caravan.
are automatically deactivated while an
Contact a PEUGEOT dealer or qualified
approved towing system is in use.
workshop for more information and to obtain a
For more information about driving with a
suitable towing device.
The load includes the weight of the items
towing device fitted to a trailer and associated
stored in the loading area (including any
with the Trailer stability assist, refer to the
fittings such as shelves), but also the weight
corresponding section.
Overload indicator
of all persons on board the vehicle, the
amount of fuel (depending on version) and
Comply with the maximum authorised
various equipment fitted on the vehicle.
towable weight, as indicated on your
For optimal performance, the vehicle must
The overload indicator is a driving aid and
be parked and loaded on level ground (avoid
vehicle's registration certificate, on the
informs you that the maximum authorised
the following conditions: parking on a slope or
manufacturer's label and in the Technical
weight has been exceeded; this may be either
straddling a pavement).
data section of this guide.
the gross vehicle weight (GVW) or the maximum
authorised weight on either axle (front and rear)
If using accessories attached to the
Attaching a trailer to your vehicle may
(GAWR).
towing device (e.g. bicycle carriers, tow
affect the operation of the system.
boxes):
The indicator does not relieve the user
- Comply with the maximum authorised nose
from their responsibility.
weight.
188
Practical information
Operation
Display of the measurement on the
Secure the load firmly.
7
instrument panel
Drive gently: the vehicle will be more
The weight on board your vehicle is measured:
susceptible to the effects of side winds and its
► When the engine starts, automatically.
If the weight on board the vehicle
stability may be affected.
exceeds the maximum authorised
Regularly check the security and tight
value, this indicator lamp comes on.
fastening of the roof bars and racks, at least
Malfunction
before each trip.
Remove the roof bars once they are no longer
Display of the malfunction in the loading
needed.
area
After the measurement is triggered from the
In the event of loading (not exceeding
loading area, the LEDs of the 3 buttons flash
40 cm in height) on the roof, do not
simultaneously for about 3 seconds and then go
exceed the following loads:
► When stationary, by pressing this
out.
ON
- Transverse bars on longitudinal bars:
button in the loading area. The system is
Consult a PEUGEOT dealer or a qualified
80 kg.
then active for 5 minutes.
workshop.
- Two transverse bars bolted to the roof:
Display of the measurement in the loading
Information displayed on the instrument
100 kg.
area
panel
- Three transverse bars bolted to the roof:
150 kg.
ON
- An aluminium rack: 120 kg.
- A steel rack: 115 kg.
If the weight on board the vehicle is nearly up to
These warning lamps come on, together with a
If the height exceeds 40 cm, adapt the speed
the maximum authorised value, the indicator
message.
of the vehicle to the profile of the road to
lamps of these buttons come on.
Consult a PEUGEOT dealer or a qualified
avoid damaging the roof bars or the roof rack
workshop.
ON
and the fixings on the vehicle.
Refer to national legislation in order to comply
If the weight on board the vehicle exceeds
Roof bars / Roof rack
with the regulations for transporting objects
the maximum authorised value, the indicator
that are longer than the vehicle.
lamps of these buttons come on.
Recommendations
Distribute the load uniformly, taking care
to avoid overloading one of the sides.
Arrange the heaviest part of the load as close
as possible to the roof.
189
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст