Peugeot Partner (2022 year). Manual in english — page 7
Driving
- depress the clutch pedal.
6-speed manual gearbox
6
Engaging 5th or 6th gear
Automatic gearbox (Type
► Move the gear selector fully to the right to
engage 5th or 6th gear.
1)
Failure to follow this instruction could
8-speed automatic gearbox which offers a choice
cause permanent damage to the gearbox
between the comfort of automatic operation or
(inadvertent engagement of 3rd or 4th gear).
manual gear changing.
Two driving modes are available:
- Automatic operation for electronic
Engaging reverse gear
P.
Park.
management of the gears by the gearbox:
R. Reverse.
- Manual operation for sequential changing of
N. Neutral.
the gears by the driver.
D. Drive (automatic operation).
In automatic mode, you can still change gear
M. Manual (manual operation with sequential
manually using the steering-mounted controls
changing of the gears).
(e.g. when overtaking).
Gear selector
Position N can be used in traffic jams or
in a car wash tunnel.
To turn the gear selector in complete
safety, it is recommended that you keep
Steering mounted controls
your foot on the brake pedal.
► Raise the ring under the knob and move the
gear lever to the left, then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine at
idle.
As a safety precaution and to facilitate
engine starting:
► Pull the right-hand "+" or left-hand "-" control
– always select neutral,
paddle towards you to change up or down.
127
Driving
The steering mounted controls do not
► Gradually release the brake pedal.
Automatic operation
allow neutral to be selected and reverse
Or
► Select position D for automatic
gear to be engaged or disengaged.
► Accelerate gradually in order to release the
changing of the gears.
electric parking brake (if it is set to automatic
The gearbox then operates in auto-adaptive
mode).
Information displayed on
mode, without any intervention on the part of the
The vehicle moves off immediately.
driver. It continuously selects the most suitable
the instrument panel
If P is displayed on the instrument panel
gear according to the driving style, the road
When you move the selector or press button M,
but the selector is in another position,
profile and the load in the vehicle.
the corresponding gear and indicator lamp are
place the selector in position P to allow the
► For maximum acceleration without
shown on the instrument panel.
engine to be started.
touching the selector, fully depress the
The "-" symbol is displayed if a value is invalid.
If position N is selected inadvertently while
accelerator pedal (kick-down).
► If the message "Foot on the brake" is
driving, allow the engine to return to idle, then
The gearbox changes down automatically or
displayed on the instrument panel, press
select position D to accelerate.
holds the gear selected until the maximum
the brake pedal firmly.
engine speed is reached.
When braking, the gearbox changes down
When the engine is running at idle with
Starting the vehicle
automatically to provide effective engine braking.
the brakes released, if position R, D or M
► With your foot on the brake, select
If you release the accelerator sharply, the
is selected, the vehicle moves even without
position P.
gearbox will not shift to a higher gear for safety
the accelerator being pressed.
► Start the engine.
reasons.
Never leave children inside the vehicle
If the conditions are not met, there is an audible
unsupervised.
Never select position N while the vehicle
signal, accompanied by a message on the
As a safety measure, never leave the vehicle
is moving.
instrument panel screen.
without taking your key or remote control with
Never select positions P or R unless the
► Release the parking brake, unless it is set to
you, even for a short time.
vehicle is completely stationary.
automatic mode (with electric parking brake).
When carrying out maintenance with the
► Select position R, N or D.
engine running, apply the parking brake and
If you are setting off from a steep slope
select position P.
Temporary manual control
with a loaded vehicle, depress the
of gear changes
brake pedal, select position D, release the
With an automatic gearbox, never try to
You can temporarily assume control of gear
parking brake, unless it is set to automatic
start the engine by pushing the vehicle.
changing using the "+" et "-” steering-mounted
mode (with electric parking brake), then
controls. The gear change request will be
release the brake pedal.
executed if the engine speed permits.
128
Driving
This function allows you to anticipate certain
► You can revert to automatic operation at any
Depending on the road configuration
6
situations, such as overtaking another vehicle or
time by pressing button M again.
(e.g. mountainous road), manual
approaching a bend in the road.
The indicator lamp for the button goes off.
operation may be preferable.
After a few seconds with no inputs via the control
Automatic operation may not always be
In manual mode, there is no need to
paddles, the gearbox reverts to automatic
suitable, and does not enable engine braking.
release the accelerator pedal while
operation.
changing gear.
Invalid value during manual
Creeping (moving without
It is only possible to change from one
operation
using the accelerator)
gear to another if the vehicle speed and
This symbol is displayed if a gear is not
This function facilitates manoeuvring of the
engine speed permit.
engaged correctly (gear selector between
vehicle at low speed (when parking, in traffic
two positions).
jams, etc.).
If the engine speed is too low or too high,
► Place the selector "correctly" at a position.
When the engine is at idle, with the parking
the selected gear flashes for a few
brake released and gear position D, M or R
seconds, then the gear actually engaged is
Switching off the vehicle
selected, the vehicle begins to creep forward
shown.
as soon as you take your foot off the brake pedal
Before switching off the engine, select position
When the vehicle is stationary or moving very
(even without pressing the accelerator).
P then apply the parking brake to immobilise
slowly, the gearbox automatically selects gear
the vehicle, unless this is set to automatic mode
As a safety precaution, never leave the
M1.
(with electric parking brake).
vehicle with the engine running and the
Check that mode P has been engaged and that
doors closed.
To preserve the brakes while descending
the electric parking brake has been applied
a steep incline, use engine braking to
automatically; if not, apply it manually.
reduce your speed (change down or select a
The corresponding indicator lamps in the
Manual operation
lower gear).
selector and the electric parking brake control
► With the selector in position D, press
Keeping the brake pedal pressed
lever must be on, as well as those on the
button M to enable 6-speed sequential
continuously for long periods can overheat
instrument panel.
gear changing.
the brakes, with the risk of damaging the
The indicator lamp for the button comes on.
A point of resistance may be noticed
braking system or making it inoperative.
► Operate the "+" or "-" steering mounted
when moving to position P.
Only use the brakes when necessary, to slow
controls.
If the selector is not in position P, when the
or stop the vehicle.
M appears and the engaged gears are
driver's door is opened or approximately 45
shown in succession on the instrument
seconds after the ignition is switched off,
panel.
129
Driving
an audible signal sounds and a message
There is a risk of damaging the gearbox:
P.
Auto Park
appears.
- If the accelerator and brake pedals are
Press this button to switch to Parking mode.
► Return the drive selector to position P;
depressed simultaneously.
For parking the vehicle: the front wheels are
the audible signal stops and the message
- In the event of a battery failure, forcing the
blocked.
disappears.
selector from position P to another position.
R. Reverse
N. Neutral
When positioned on a steep slope with a
Automatic gearbox
To free-wheel and move the vehicle, with the
loaded vehicle, depress the brake
Never try to start the engine by pushing
ignition off.
pedal, select position P, apply the parking
the vehicle.
For more information on Free-wheeling, refer
brake, unless it is set to automatic mode (with
to the corresponding section.
electric parking brake), then release the brake
D. Driving in automatic mode
pedal.
Automatic gearbox (Type
The gearbox manages gear changes
according to the style of driving, the road
2)
In all circumstances, ensure that the
profile and the vehicle load.
selector is in position P before leaving
Automatic 8-speed gearbox with push selector.
M. Driving in manual mode (Petrol/Diesel)
your vehicle.
It also offers a manual mode with gear changes
Press this button to switch to manual mode.
via control paddles located behind the steering
The driver changes gear using the steering-
wheel.
mounted controls.
Malfunction
► In mode N, with your foot on the brake pedal,
In the event of a malfunction, this warning
Push selector
push without passing the point of resistance:
lamp comes on and a message is
• Forwards, mode R is selected.
displayed, when the ignition is switched on.
• Backwards, mode D is selected.
In this case, the gearbox goes into back-up
Release the selector fully after each push; it
mode and is locked in 3rd gear. You may feel a
will then return to its initial position.
significant jolt (without risk to the gearbox) when
Special cases
changing from P to R and from N to R.
Do not exceed 62 mph (100 km/h), local speed
To avoid mode N (quick change from D to R and
restrictions permitting.
back again):
Have the system checked by a PEUGEOT
► In mode R, push backwards past the point of
dealer or a qualified workshop.
resistance, mode D is selected.
► In mode D, push forwards past the point of
resistance, mode R is selected.
130
Driving
► To return to mode N, push without passing
M1...8
Manual forward gear
In the event of battery failure, it is
6
the point of resistance.
essential to place the chock(s) supplied
The state of the gearbox remains displayed on
with the tool kit against one of the wheels to
Steering-mounted controls
the instrument panel for a few seconds after
immobilise the vehicle.
switching off the ignition.
(Depending on equipment)
In mode M or D, the steering-mounted control
Operation
Special aspects of automatic mode
paddles can be used to change gear manually.
Only appropriate mode change instructions are
The gearbox selects the gear that provides
They cannot be used to select neutral or to
validated.
optimal performance based on ambient
engage or disengage reverse gear.
With the engine running, if it is necessary to
temperature, road profile, vehicle loading and
depress the brake pedal to change modes,
driving style.
an alert message will be displayed on the
For maximum acceleration, press the accelerator
instrument panel.
fully down (kick-down). The gearbox changes
down automatically or holds the selected gear
With the engine running and the brakes
until the maximum engine speed is reached.
released, if R, D or M is selected, the
Steering mounted controls allow the driver to
vehicle moves off, even without pressing the
temporarily select a gear, if the vehicle speed
accelerator pedal.
and engine speed conditions permit.
Never depress the accelerator and brake
pedals at the same time - risk of damage to
Special aspects of manual mode
the gearbox!
The gearbox only changes from one gear to
► Pull the "+" or "-" paddle towards you and
another if the vehicle speed and engine speed
If you open the driver's door while mode
conditions permit.
release to shift up or down a gear, respectively.
N is engaged, an audible signal will
sound and mode P will be engaged. The
Starting the vehicle
Information displayed on
audible signal stops when the driver's door is
► Fully depress the brake pedal.
the instrument panel
closed.
► Start the engine.
When the ignition is switched on, the gearbox
► With your foot on the brake pedal, push once
status is displayed on the instrument panel:
At speeds below 3 mph (5 km/h),
or twice backwards to select automatic mode D,
P
Parking
opening the driver’s door will engage
or forwards to shift into reverse gear R.
R
Reverse
mode P - risk of sudden braking!
► Release the brake pedal.
N
Neutral
► Accelerate gradually to automatically release
D1...8
Automatic forward gear
the electric parking brake.
131
Driving
The vehicle moves off immediately.
The paddles on the steering wheel do not work
Drive selector (Electric)
and mode M is no longer accessible.
Automatic gearbox
You may feel a significant jolt on engaging
Never try to start the engine by pushing
reverse gear. This will not damage the gearbox.
the vehicle.
Selector malfunction
Switching the vehicle off
Minor malfunction
Regardless of the current gearbox mode, mode
This warning lamp comes on,
P is immediately engaged automatically when
accompanied by the display of a message
the ignition is switched off.
and an audible signal.
However, in mode N, mode P will be engaged
Drive carefully.
after a delay of 5 seconds (time to enable free-
Go to a PEUGEOT dealer or a qualified
wheeling mode).
workshop.
The drive selector is a pulse selector with a
Check that mode P has been engaged and
In some cases, the selector indicator lamps may
regenerative braking function.
that the electric parking brake was applied
no longer come on, but the gearbox state is still
The drive selector provides traction control
automatically; if not, apply it manually.
displayed on the instrument panel.
based on the driving style, the road profile and
The corresponding indicator lamps on the
Major malfunction
the vehicle load.
gear selector and the electric parking
With regenerative braking activated, it also
brake control must be on, as well as the
This warning lamp comes on,
manages engine braking when the accelerator
indicator lamps on the instrument panel.
accompanied by the display of a
pedal is released.
message.
P. Park
Gearbox malfunction
You must stop the vehicle.
Button for parking the vehicle: the front
This warning lamp comes on,
Stop as soon as it is safe to do so and
wheels are locked (the button lights up to
accompanied by an audible signal and
switch off the ignition.
indicate that it is activated).
the display of a message.
Contact a PEUGEOT dealer or a qualified
R. Reverse
Go to a PEUGEOT dealer or a qualified
workshop.
To engage reverse gear, with your foot on the
workshop.
brake pedal.
Do not drive faster than 62 mph (100 km/h),
keeping to the speed limit.
Switching of the gearbox to back-up mode
Mode D locks in third gear.
132
Driving
N. Neutral
Regenerative braking
With the brake pedal
6
To move the vehicle with the ignition off and
When the brake pedal is depressed, the
With the Brake function and when
so allow it to free-wheel.
intelligent braking system automatically recovers
decelerating
For more information on Free-wheeling, refer
some of the energy and uses it to recharge the
The Brake function emulates engine braking,
to the corresponding section.
traction battery.
slowing the vehicle with no need to depress the
D. Drive (automatic forward gear)
This energy recovery also reduces use of the
brake pedal. The vehicle slows more quickly
B. Brake (regenerative braking)
brake pads, thereby limiting their wear.
when the driver releases the accelerator pedal.
Regenerative braking (the button lights up to
The energy recovered when the accelerator
The driver may experience a different
indicate its activation).
pedal is released is then used to partially
sensation when depressing the brake
recharge the traction battery, thereby increasing
pedal compared to a vehicle without
Information displayed on
the vehicle's driving range.
regenerative braking.
the instrument panel
The resulting deceleration of the vehicle
When the ignition is switched on, the drive
does not cause the brake lamps to come
selector status is displayed on the instrument
Driving modes
on.
panel:
Driving modes are selected using the following
P : Park.
► From mode D/R, press button B to activate/
control:
R : Reverse.
deactivate the function (the button lights up when
N : Neutral.
the function is activated).
D : Drive (automatic forward gear).
D/R on the instrument panel is replaced with B.
B : Brake (regenerative braking activated).
The system status is not saved when the ignition
is switched off.
Operation
In some situations (e.g. battery full,
► Move the selector by pressing it forwards
extreme temperatures), the amount of
(N or R) or rearwards (N or D) once or twice,
regenerative braking may be temporarily
passing the point of resistance if necessary.
limited, resulting in less deceleration.
For example, to change from P to R (with your
The driver must remain alert to traffic
foot on the brake pedal), either push forwards
conditions and must always be ready to use
twice without passing the point of resistance or
the brake pedal.
push just once, passing the point of resistance.
1.Pressing the control activates Eco mode. The
indicator lamp comes on. (Petrol or Diesel)
133
Driving
2.Pressing the control displays the modes on the
D, gradually releasing the accelerator pedal
The system adapts the gear change
instrument panel.
fully allows free-wheeling which can save fuel.
instructions according to the driving
With an electric motor, when starting the vehicle,
A drop in engine speed is normal (rev counter
conditions (e.g. slope, load) and driving style
no mode can be selected until the READY
at idle, drop in engine noise).
(e.g. power demand, acceleration, braking).
indicator lamp is displayed.
The system never suggests:
When the message disappears, the selected
- engaging first gear;
mode is activated and remains indicated on the
Gear shift indicator
- engaging reverse gear.
instrument panel (except Normal mode).
(Depending on engine)
Whenever the ignition is switched on,
This system is designed to reduce fuel
Normal driving mode is selected by default.
Stop & Start (Petrol or
consumption by recommending the most suitable
Normal
gear.
Diesel)
To restore the default settings.
The Stop & Start function puts the engine
Operation
Eco
temporarily into standby - STOP mode - during
Depending on the driving situation and
To reduce energy consumption by reducing the
phases when the vehicle is stationary (e.g. red
the vehicle's equipment, the system may
performance of the heating and air conditioning,
lights, traffic jams). The engine automatically
recommend skipping one or more gears.
without deactivating them.
restarts - START mode - as soon as the driver
Gear engagement recommendations are
To reduce consumption of the traction battery's
indicates the intention of moving off again.
not to be considered mandatory. Indeed, the
electrical energy by limiting engine torque.
Primarily designed for urban use, the function
configuration of the road, the traffic density and
Power (Electric)
is intended to reduce fuel consumption and
safety remain determining factors when choosing
exhaust emissions as well as the noise level
Allows a fully laden vehicle (GVW) to obtain
the best gear. Therefore, the driver remains
when stationary.
equivalent performance to that of an unladen
responsible for deciding whether or not to follow
The function does not affect the functionalities of
vehicle in Normal mode.
the system’s advice.
the vehicle, in particular the braking.
The system cannot be deactivated.
All modes are displayed on the
Opening the bonnet
instrument panel, except for Normal
With an automatic gearbox, the system is
Before doing anything under the bonnet,
mode.
only active in manual operation.
deactivate the Stop & Start system to avoid
any risk of injury caused by the engine
The information appears on the
Coasting mode
restarting automatically.
instrument panel, in the form of an “up” or
Depending on version or engine, with an
“down” arrow and the recommended gear.
EAT8 gearbox and the gear selector in mode
134
Driving
Driving on flooded roads
The system is reactivated automatically
Time counter
6
Before entering into a flooded area, it is
whenever the engine is started by the
A time counter adds up the time spent in standby
strongly recommended that you deactivate
driver.
during the journey. It is reset to zero every time
the Stop & Start system.
the ignition is switched on.
For more information on Driving
Operation
recommendations, particularly on flooded
Special cases:
roads, refer to the corresponding section.
Main conditions for operation
The engine will not go into standby if the
- The driver’s door must be closed.
conditions for operation are not met and in the
Deactivation/Activation
- The sliding side door must be closed.
following cases:
- The driver's seat belt must be fastened.
- Steep slope (ascending or descending).
With button
- The level of charge in the battery must be
- Vehicle has not exceeded 6 mph (10 km/h)
sufficient.
since the last engine start (with the key or the
- The temperature of the engine must be within
START/STOP button).
its nominal operating range.
- Electric parking brake applied or being
- The outside temperature must be between
applied.
0°C and 35°C.
- Needed to maintain a comfortable temperature
in the passenger compartment.
Putting the engine into standby
- Demisting active.
(STOP mode)
In these cases, this indicator lamp flashes
The engine automatically enters standby mode
for a few seconds, then goes off.
► To deactivate or reactivate the system, press
as soon as the driver indicates their intention to
this button.
After the engine has restarted, STOP
stop:
The indicator lamp is on when the system is
mode is not available until the vehicle
- With a manual gearbox: at a speed below
deactivated.
has reached a speed of 5 mph (8 km/h).
2 mph (3 km/h) or with the vehicle stationary
With touch screen
(depending on engine), with the gear lever in
During parking manoeuvres, STOP mode
neutral and the clutch pedal released.
The system is activated/
is not available for a few seconds after
- With an automatic gearbox: at a speed below
deactivated via the Vehicle/
coming out of reverse gear or turning the
2 mph (3 km/h) or with the vehicle stationary
Driving touch screen menu.
steering wheel.
(depending on engine), with the brake pedal
If the system has been deactivated in
depressed or the gear selector in position N.
STOP mode, the engine restarts
immediately.
135
Driving
Restarting the engine (START mode)
Have it checked by a PEUGEOT dealer or a
essential that the tyre pressure is correct during
The engine automatically restarts as soon as the
qualified workshop.
the operation. This operation is the driver’s
driver indicates the intention of moving off again:
The vehicle stalls in STOP mode
responsibility.
With a manual gearbox: with the clutch pedal
All of the instrument panel warning lamps come
The tyre under-inflation detection cannot,
fully depressed.
on if there is a fault.
in any circumstances, replace the need
With an automatic gearbox:
Depending on version, a warning message
for vigilance on the part of the driver.
- With the selector in position D or M: with the
may also be displayed, prompting you to place
This system does not avoid the need to
brake pedal released.
the gear selector in position N and depress the
regularly check the tyre pressures (including
- With the selector in position N and the brake
brake pedal.
the spare wheel), especially before a long
pedal released: with the selector at D or M.
► Switch off the ignition then start the engine
journey.
- With the selector in position P and the brake
again with the key or the "START/STOP" button.
Driving with under-inflated tyres, particularly
pedal depressed: with the selector at R, N, D
in adverse conditions (heavy load, high
or M.
12 V battery
speed, long journey):
- Reverse gear engaged.
The Stop & Start system requires a
- worsens road-holding.
12 V battery of specific technology and
- lengthens braking distances.
Special cases
specification.
- causes premature wear of the tyres.
The engine will restart automatically if the
All work must be carried out only by a
- increases energy consumption.
conditions for operation are met again and in the
PEUGEOT dealer or a qualified workshop
following case:
The inflation pressures defined for the
- Vehicle speed exceeds 2 mph (3 km/h)
vehicle can be found on the tyre pressure
(depending on engine).
Tyre under-inflation
label.
In this case, this indicator lamp flashes for
detection
For more information on the Identification
a few seconds, then goes off.
markings, refer to the corresponding section.
This system alerts the driver if one or more tyres
Malfunctions
suffer a drop in pressure.
The alert is raised when the vehicle is moving,
Checking tyre pressures
Depending on the vehicle’s equipment:
not when stationary.
This check should be done monthly
In the event of a system malfunction, this
It compares the information given by the wheel
when the tyres are "cold" (vehicle stopped for
warning lamp flashes on the instrument
speed sensors with reference values, which
1 hour or after a journey of less than 6 miles
panel.
must be reinitialised every time the tyre
(10 km) at moderate speeds).
The warning lamp in this button flashes
pressures are adjusted or a wheel changed.
Otherwise, add 0.3 bar to the pressures
and a message appears, accompanied by
It takes into account the last values stored
shown on the label.
an audible signal.
during the reinitialisation request. It is therefore
136
Driving
Snow chains
Driving too slowly may not ensure
Without touch screen
6
The system does not have to be
optimum monitoring.
reinitialised after fitting or removing snow
The alert is not immediately triggered in the
chains.
event of a sudden loss of pressure or tyre
blow-out. This is because analysis of the
Spare wheel
values read by the wheel's speed sensors
The steel spare wheel does not have an
can take several minutes.
under-inflation detection sensor.
The alert may be delayed at speeds below
25 mph (40 km/h), or when adopting a sporty
driving mode.
► With the vehicle stationary, press this
Under-inflation alert
button for about 3 seconds then release it.
This is signalled by the fixed illumination
The alert is kept active until the system is
Reinitialisation is confirmed by an audible signal.
of this warning lamp, accompanied by an
reinitialised.
audible signal and, depending on equipment, the
With touch screen
display of a message.
With the vehicle stationary, the
► Reduce speed immediately, avoid excessive
Reinitialisation
system is reinitialised via the
steering movements and avoid sudden braking.
► The system must be reinitialised after any
Driving/Vehicle touch screen menu.
► Stop the vehicle as soon as it is safe to do
adjustment to the pressure of one or more tyres,
so.
and after changing one or more wheels.
Malfunction
The loss of pressure detected may not
Before reinitialising the system, make
In the event of a malfunction,
always cause visible deformation of the
sure that the pressures of the four tyres
these warning lamps light up on
tyre.
are correct for the conditions of use of the
the instrument panel.
Do not rely on just a visual check.
vehicle and conform to the values written on
In this case, the tyre under-inflation monitoring
the tyre pressure label.
function is no longer performed.
► Using a compressor, such as the one in
Check the pressures of the four tyres before
Have it checked by a PEUGEOT dealer or a
the temporary puncture repair kit, check the
performing the reinitialisation.
qualified workshop.
pressures of all four tyres when cold.
The system does not advise if a pressure is
Non-standard spare wheel
► If it is not possible to carry out this check
incorrect at the time of reinitialisation.
The use of this type of spare wheel may
immediately, drive carefully at reduced speed.
suspend tyre pressure monitoring.
► In the event of a puncture, use the
In this case, the malfunction warning lamp
temporary puncture repair kit or the spare wheel
comes on and disappears once the wheel
(depending on equipment).
has been replaced by one of uniform size (the
137
Driving
same as the others), the pressure readjusted
Manoeuvring aids
Poor visibility (inadequate street lighting,
and the reinitialisation carried out.
The driver must always check the
heavy rain, thick fog, snowfall), dazzle
surroundings of the vehicle before and during
(headlamps of an oncoming vehicle, low sun,
the whole manoeuvre, in particular using the
reflections on a damp road, leaving a tunnel,
Driving and manoeuvring
mirrors.
alternating shade and light) can also impair
detection performance.
aids - General
Radar(s)
In the event of a windscreen replacement,
recommendations
The operation of the radar(s), along with
contact a PEUGEOT dealer or a qualified
any associated functions, may be affected
workshop to recalibrate the camera;
Driving and manoeuvring aids cannot, in
by the accumulation of dirt (e.g. mud, ice),
otherwise, the operation of the associated
any circumstances, replace the need for
in poor weather conditions (e.g. heavy rain,
driving aids may be disrupted.
vigilance on the part of the driver.
snow), or if the bumpers are damaged.
The driver must comply with the Highway
If the front bumper is to be repainted, contact
Other cameras
Code, must remain in control of the vehicle in
a PEUGEOT dealer or a qualified workshop;
The images from the camera(s)
all circumstances and must be able to retake
certain types of paint could interfere with the
displayed on the touch screen or on the
control of it at all times. The driver must adapt
operation of the radar(s).
instrument panel may be distorted by the
the speed to climatic conditions, traffic and
terrain.
the state of the road.
In the presence of areas in shade, or in
It is the driver's responsibility to constantly
conditions of bright sunlight or inadequate
monitor traffic conditions, assess the distance
lighting, the image may be darkened and with
and relative speed of other vehicles, and
lower contrast.
anticipate their manoeuvres before using the
Obstacles may appear further away than they
direction indicator and changing lanes.
actually are.
These systems do not make it possible to
exceed the laws of physics.
Sensors
Driving aids camera
The operation of the sensors, as well as
This camera and its associated functions
Driving aids
any associated functions, may be disrupted
may be impaired or not work if the windscreen
You should hold the steering wheel with
by noise pollution such as that emitted by
area in front of the camera is dirty, misty,
both hands, always use the door and interior
noisy vehicles and machinery (e.g. lorries,
frosty, covered with snow, damaged or
mirrors, always leave your feet close to the
pneumatic drills), by the accumulation of
masked by a sticker.
pedals and take a break every 2 hours.
snow or dead leaves on the road or in the
In humid and cold weather, demist the
event of damaged bumpers and mirrors.
windscreen regularly.
138
Driving
When reverse gear is engaged, an audible
Units of speed
- Signs indicating a shared traffic zone detected
6
signal (long beep) indicates that the sensors
Ensure that the units of speed displayed
by the camera.
may be dirty.
on the instrument panel (mph or km/h) are
Sign detected
Suggested speed
A front or rear impact to the vehicle can
those for the country you are driving in.
(calculated)
upset the sensors’ settings, which is not
If this is not the case, when the vehicle is
always detected by the system: distance
stationary, set the display to the required
Entry into a shared
Without PEUGEOT
measurements may be distorted.
units of speed so that it complies with what is
traffic zone
Connect Nav
The sensors do not systematically detect
authorised locally.
Example:
10 mph or 20 km/h
obstacles that are too low (pavements, studs)
In case of doubt, contact a PEUGEOT dealer
(depending on
or too thin (trees, posts, wire fences).
or a qualified workshop.
the units on the
Certain obstacles located in the sensors’ blind
instrument panel)
spots may not be detected or may no longer
With PEUGEOT
be detected during the manoeuvre.
Connect Nav
Road signs recognition
Certain materials (fabrics) absorb sound
Display of the speed
waves: pedestrians may not be detected.
For more information, refer to the
in force in the country
you are driving in.
General recommendations on the use
Maintenance
of driving and manoeuvring aids.
- Some supplementary traffic signs detected by
Clean the bumpers and door mirrors and
the camera.
the field of vision of the cameras regularly.
When washing your vehicle at high pressure,
direct the spray from at least 30 cm away
from the sensors and cameras.
Mats/Pedal trims
The use of mats or pedal trims not
approved by PEUGEOT may interfere with
the operation of the speed limiter or cruise
This system displays the maximum speed
control.
authorised locally on the instrument panel, using:
To avoid any risk of jamming the pedals:
- Speed limit signs detected by the camera.
- Ensure that the mat is secured correctly.
- Speed limit information from the navigation
– Never fit one mat on top of another.
system’s mapping.
139
Driving
The units for the speed limit (mph or
Supplementary
Display of
Supplementary
Display of
km/h) depend on the country you are
traffic sign detected
the speed
traffic sign detected
the speed
driving in.
associated with
associated with
This should be taken into account to ensure
the supplementary
the supplementary
you observe the speed limit.
traffic sign
traffic sign
For the system to work properly when
Speed limit when
If the wiper control
Speed limit for
56 mph (90 km/h)
changing countries, the speed unit of the
raining
stalk is in the
vehicles with a
(for example)
instrument panel must match that of the
Examples:
"intermittent wipe"
gross vehicle
country you are driving in.
or "automatic wipe"
weight or gross
position (in order
train weight less
Automatic sign reading is a driving aid
to activate the rain
than 3.5 tonnes
system and does not always display the
sensor):
correct speed limits.
68 mph (110 km/h)
The speed limit signs present on the road
(for example)
Speed limit in case
If the outside
always take priority over those displayed by
Speed limit when
If an approved towing
of snow
temperature is below
the system.
towing
device is fixed to the
Example:
3°C:
The system is designed to detect signs that
vehicle:
19 mph (30 km/h)
conform to the Vienna Convention on road
56 mph (90 km/h)
(for example)
signs.
(for example)
with a "snowflake"
symbol
Specific speed limits, such as those for
Speed limit
43 mph (70 km/h)
heavy goods vehicles, are not displayed.
applicable over a
(for example)
Speed limit at
19 mph (30 km/h)
The display of the speed limit on the
certain distance
certain times of the
(for example)
instrument panel is updated when passing
Example:
day
with a "clock" symbol
a speed limit sign intended for cars (light
Example:
vehicles).
Activation/Deactivation
By default, the system is automatically activated
Navigation mapping should be regularly
at every engine start.
updated in order to receive accurate
speed limit information from the system.
140
Driving
The settings are changed via the
(5 km/h) (e.g. 59 mph (95 km/h)), the speed is
For more information on the Speed
6
Driving/Vehicle touch screen
displayed and flashes for 10 seconds (depending
limiter, Cruise control or Adaptive
menu.
on version).
cruise control, refer to the corresponding
sections.
Information displayed on
Operating limits
the instrument panel
The system does not take account of reduced
Steering-mounted controls
speed limits, especially those imposed in the
following cases:
- Atmospheric pollution.
- Towing.
1. Detected speed limit indication
- Driving with a space-saver type spare wheel
or
or snow chains fitted.
2. End of speed limit indication
- Tyre repaired using the temporary puncture
repair kit.
1. Speed limiter/cruise control mode selection
- Young drivers.
2. Memorise the speed setting
The system may not display the speed limit if it
does not detect a speed limit sign within a preset
Information displayed on the
period and in the following situations:
The system is active but is not detecting speed
instrument panel
- Road signs that are obstructed, non-standard,
limit information.
damaged or bent.
- Obsolete or incorrect maps.
Recommendation
3. Speed limit indication
4. Speed memorisation prompt
On detecting speed limit information, the system
5. Current speed setting
displays the value.
Storing the speed setting
In addition to Road signs recognition, the
driver can select the speed displayed as a speed
setting for the speed limiter or cruise control
For a suggested maximum speed, the first time
using the speed limiter or cruise control 'store'
that the vehicle exceeds it by more than 3 mph
button.
141
Driving
► Switch on the speed limiter/cruise control.
This system prevents the vehicle from
The speed limiter/cruise control information is
exceeding the speed programmed by the
displayed.
driver (speed setting).
Upon detecting a sign suggesting a new speed
The speed limiter is switched on manually.
setting, the system displays the value and
This additional system recognises these road
The minimum speed setting is 19 mph (30 km/h).
"MEM" flashes for a few seconds, prompting you
signs and displays them on the instrument panel
The speed setting remains in the system
to save it as a new speed setting.
if the appropriate display mode is selected:
memory when the ignition is switched off.
- No entry: when entering a lane in the wrong
If there is a difference of less than 6 mph
direction, an alert message, including the symbol
Steering-mounted control
(9 km/h) between the speed setting and
of this sign, is displayed on the instrument panel
the speed displayed by the Road signs
(request to check the direction of traffic).
recognition, the "MEM" symbol is not
- Other signs: as you approach it, the symbol
displayed.
of the corresponding sign is displayed on the
instrument panel.
Depending on the road conditions, several
speeds may be displayed.
The actual road signs always take priority
► Press button 2 once to save the suggested
over those displayed by the system.
speed value.
The signs must comply with the Vienna
A message is displayed, confirming the request.
Convention on road signs.
► Press button 2 again to confirm and save the
1.
ON (LIMIT position)/OFF (position 0)
new speed setting.
Activation/Deactivation
2.
Reduce the speed setting
The display then reverts to its previous state.
3.
Increase the speed setting
The settings are changed via
4.
Pause/resume speed limiter with the speed
Extended Traffic Sign
the Driving/Vehicle touch screen
setting previously stored
menu.
Recognition
5.
Depending on version:
Display the speed thresholds saved using the
For more information, refer to the
Speed limiter
Memorising speeds function
General recommendations on the use
or
of driving and manoeuvring aids.
For more information, refer to the
Use the speed suggested by the Road signs
General recommendations on the use
recognition (MEM display)
of driving and manoeuvring aids.
6.
Display and adjustment of the programmed
inter-vehicle distance
142
Driving
For more information on Memorising speeds
► If the speed limit setting is suitable (most
► Press button 5 once; a message is displayed
6
or the Road signs recognition, refer to the
recent speed setting programmed in the system),
to confirm the memorisation request.
corresponding sections.
press button 4-II to switch the speed limiter on.
► Press button 5 again to save the suggested
► Pressing 4-II again temporarily pauses the
speed.
Information displayed on
function (pause).
The speed is immediately shown on the
instrument panel as the new speed setting.
the instrument panel
When the speed setting remains below
the vehicle's speed for a prolonged
Temporarily exceeding the
period of time, an audible warning is emitted.
speed setting
► Fully depress the accelerator pedal.
Adjusting the limit speed
The speed limiter is temporarily deactivated and
setting
the displayed speed setting flashes.
You do not have to switch the speed limiter on in
► Release the accelerator pedal to return to
order to set the speed.
below the speed setting.
To modify the limit speed setting based on the
When exceeding the speed is not due to the
vehicle’s current speed:
driver's action (e.g. in case of a steep slope), an
► Briefly press button 2 or 3 to change the
audible signal is triggered immediately.
value in steps of + or - 1 mph (1.6 km/h).
On a steep descent or in the event of
► Press and hold button 2 or 3 to change the
sharp acceleration, the speed limiter will
value in steps of + or - 5 mph (8 km/h).
not be able to prevent the vehicle from
To change the limit speed setting using
exceeding the speed setting.
7.
Speed limiter mode selection indication
memorised speeds, via the touch screen:
If necessary, apply the brakes to control your
8.
Speed limiter on/pause status indication
► Press button 5 to display the memorised
vehicle’s speed.
9.
Programmed speed setting value
speed settings.
10.
Speed limiter recommendation with Road
► Press the touch screen button for the desired
When the vehicle speed returns to the speed
signs recognition (depending on version)
speed setting.
setting level, the speed limiter operates again:
The selection screen closes after a few
the speed setting display becomes fixed again.
Switching on/Pausing
moments.
This setting becomes the new limit speed.
Switching off
► Turn thumbwheel 1 to the "LIMIT" position
to select speed limiter mode; the function is
To modify the cruise speed setting based on the
► Turn the thumbwheel 1 to the "0" position:
paused.
speed suggested by the Road signs recognition,
the display of information on the speed limiter
as shown on the instrument panel:
disappears.
143
Driving
Malfunction
The maximum speed is originally set
Exceeding the programmed speed
according to the regulations in force in
setting
the country of sale.
You can temporarily exceed the speed
This maximum speed cannot be changed by
setting by pressing the accelerator pedal (the
the driver.
programmed speed flashes).
If you wish to modify this maximum speed,
To return to the speed setting, release the
contact a PEUGEOT dealer.
accelerator pedal (when the set speed is
reached again, the displayed speed stops
In the event of a malfunction, dashes are
flashing).
displayed flashing and then fixed instead of the
Cruise control - Specific
speed setting.
Operating limits
Have it checked by a PEUGEOT dealer or a
recommendations
Never use the system in the following
qualified workshop.
situations:
The cruise control function does not
- In an urban area with the risk of
guarantee compliance with the maximum
Fixed speed limiter
pedestrians crossing the road.
authorised speed and the safety distance
- In heavy traffic (except versions with the
between vehicles, the driver remains
Stop & Go function).
responsible for their driving.
- On winding or steep roads.
In the interest of public safety, only use cruise
- On slippery or flooded roads.
control if the traffic conditions enable vehicles
- In poor weather conditions.
to drive at a steady speed and maintain an
- In the event of restricted visibility for the
adequate safety distance.
driver.
Remain vigilant while cruise control is
- Driving on a speed circuit.
activated. If you press and hold one of the
- Driving on a rolling road.
speed setting modification buttons, your
- When using a ‘space-saver’ type spare
vehicle may change speed very abruptly.
If fitted to your vehicle, its speed can be limited
wheel.
When descending a steep hill, the cruise
to a fixed setting.
- When using snow chains, non-slip covers
control system cannot prevent the vehicle
A label located in the passenger compartment
or studded tyres.
from exceeding the set speed. Brake if
indicates this maximum speed.
necessary to control the vehicle speed.
The fixed speed limiter is not a cruise control
On steep climbs or when towing, the set
type function. It cannot be activated or
speed may not be reached or maintained.
deactivated by the driver during the trip.
144
Driving
Programmable cruise
Steering-mounted control
Information displayed on
6
control
the instrument panel
For more information, refer to the
General recommendations on the use
of driving and manoeuvring aids and the
Cruise control - particular
recommendations.
This system automatically maintains the
vehicle’s speed at the value programmed
by the driver (speed setting), without the use of
1.
ON (CRUISE position)/OFF (position 0)
the accelerator pedal.
2.
Activate cruise control at the current speed/
Cruise control is switched on manually.
decrease speed setting
It requires a minimum vehicle speed of 25 mph
3.
Activate cruise control at the current speed/
6.
Cruise control mode selection indication
(40 km/h).
increase speed setting
7.
Cruise control pause/resume status indication
With a manual gearbox, third gear or higher must
4.
Pause/resume cruise control with the speed
8.
Programmed speed setting value
be engaged.
setting previously saved
9.
Cruise control recommendation with Road
With an automatic gearbox, mode D or second
5.
Depending on version:
signs recognition (depending on version)
gear or higher in mode M must be engaged.
Display the speed thresholds saved using the
With a drive selector, mode D or B must be
Memorising speeds function
Switching on/pausing
engaged.
or
► Turn thumbwheel 1 to the "CRUISE" position
Use the speed suggested by the Road signs
Cruise control remains active after
to select cruise control mode; the function is
recognition (MEM display)
changing gear, regardless of the gearbox
paused.
type, on engines fitted with the Stop & Start
For more information on Memorising speeds
► Press button 2-SET- or 3-SET+ to activate
function.
or the Road signs recognition, refer to the
cruise control and save a speed setting when
corresponding sections.
the vehicle has reached the desired speed; the
vehicle’s current speed is saved as the speed
Switching off the ignition cancels any
setting.
speed setting.
► Release the accelerator pedal.
► Pressing button 4-II temporarily pauses the
function (pause).
145
Driving
► Pressing button 4-II again resumes operation
► Press the touch screen button for the desired
vehicle from exceeding the programmed
of the cruise control (ON).
speed setting.
speed.
The selection screen closes after a few
You may have to brake to control the speed of
Cruise control can also be paused
moments.
your vehicle. In this case, the cruise control is
temporarily:
This setting becomes the new cruise speed.
automatically paused.
- by pressing the brake pedal.
To modify the cruise speed setting using the
To activate the system again, with the vehicle
- automatically, if the electronic stability
speed suggested by the Road signs recognition
speed above 25 mph (40 km/h), press button
control (ESC) system is triggered.
shown on the instrument panel:
4.
► Press button 5 once; a message is displayed
Modifying the cruise speed
to confirm the memorisation request.
Switching off
► Press button 5 again to save the suggested
setting
speed.
► Turn the thumbwheel 1 to the "0” position: the
Cruise control must be active.
cruise control information disappears from the
The speed is immediately shown on the
To modify the cruise speed setting, based on the
screen.
instrument panel as the new speed setting.
current speed of the vehicle:
► Briefly press button 2 or 3 to change the
Temporarily exceeding the
Malfunction
value in steps of + or - 1 mph (km/h).
programmed speed
► Press and hold button 2 or 3 to change the
value in steps of + or - 5 mph (km/h).
If needed (when overtaking, for example) it is
possible to exceed the programmed speed by
Pressing and holding button 2 or
pressing the accelerator pedal.
3 results in a rapid change in the speed
Cruise control is temporarily deactivated and the
of the vehicle.
programmed speed displayed flashes.
In the event of a malfunction, dashes are
To return to the programmed speed, simply
displayed flashing and then fixed instead of the
As a precaution, we recommend setting
release the accelerator pedal.
speed setting.
a cruise speed fairly close to the current
Once the vehicle has returned to the
Have it checked by a PEUGEOT dealer or a
speed of your vehicle, to avoid any sudden
programmed speed, cruise control takes over
qualified workshop.
acceleration or deceleration of the vehicle.
again and the programmed speed setting stops
flashing.
To change the cruise speed setting using
Adaptive cruise control
memorised speed settings and from the touch
When descending a steep hill, the cruise
screen:
control system cannot prevent the
For more information, refer to the
► Press button 5 to display the memorised
General recommendations on the use
speed settings.
146
Driving
of driving and manoeuvring aids and the
If the driver activates the direction
6. Display and adjustment of the distance
6
Cruise control - particular
indicator to overtake a slower vehicle,
setting to the vehicle in front
recommendations.
cruise control may temporarily reduce the
distance to the target vehicle to facilitate
This system automatically maintains the vehicle
Use
overtaking, without exceeding the speed
speed at a value set by the driver (speed
setting.
Activating the system (pause)
setting), while respecting a safety distance from
► With the engine running, turn thumbwheel
the vehicle in front (target vehicle) previously set
1 downwards to the CRUISE position. Cruise
by the driver. The system automatically manages
Steering-mounted controls
control is ready to operate (grey display).
the acceleration and deceleration of the vehicle.
With a manual gearbox, the system slows the
Switching on cruise control and setting
vehicle down as far as a speed of 19 mph (30
the speed
km/h).
With a manual gearbox, your speed must be
With the Stop function, the system manages
between 19 and 99 mph (30 and 160 km/h).
braking until the vehicle comes to a complete
With an automatic gearbox or a drive selector,
stop.
mode D or M must be selected and your speed
must be between 19 and 99 mph (30 and
The brake lamps come on if the vehicle
160 km/h).
is slowed down by the system.
► Press 2-SET- or 3-SET+: the current speed
It can be dangerous to drive if the brake
1.
ON (CRUISE position)/OFF (position 0)
becomes the speed setting (minimum 19 mph
lamps are not in perfect working order.
2.
Activation of cruise control at the current
(30 km/h)) and cruise control is immediately
speed/decrease speed setting
activated (green display).
3.
Activation of cruise control at the current
► Press 3-SET+ to increase or 2-SET- to
speed/increase speed setting
decrease the speed setting (steps of 5 mph
4.
Pause/resume cruise control with the speed
(km/h) if held pressed).
setting previously saved
To do this, the system uses a camera fitted at
Pressing and holding either 2-SET- or
5.
Depending on version:
the top of the windscreen and, depending on
3-SET+ results in a rapid change in the
Display the speed thresholds saved using the
version, a radar fitted in the front bumper.
speed of the vehicle.
Memorising speeds function
Primarily designed for driving on main
or
Pausing/resumption of cruise control
roads and motorways, this system only
Use the speed suggested by the Road signs
works with moving vehicles driving in the
recognition (MEM display)
► Press 4-II or depress the brake pedal (grey
same direction as your vehicle.
display).
147
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст