Peugeot 307 Break (2007 year). Instruction — part 6
72
Automatic switching on of the
lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of
the windscreen wipers. They switch
off as soon as the light becomes
bright enough or the windscreen wip-
ers stop.
Note: in foggy weather or in snow,
the brightness sensor can detect suf-
ficient light. As a consequence, the
lights will not come on automatically.
Deactivation
Turn ring
A to a position other
than
"AUTO". Switching off is ac-
companied by a message on the
multifunction display.
If the brightness sensor does not
function correctly, the lights come
on accompanied by the service
warning light, an audible signal and
a message on the multifunction dis-
play.
Contact a PEUGEOT dealer.
Manual "Follow-me-home" lighting
When the automatic switching on of
the lights function is deactivated, the
side lights and dipped headlamps re-
main on for the duration selected for the
automatic "follow-me-home" lighting.
If the vehicle is not fitted with the
automatic switching on of the lights
function, when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
Direction indicators (flashers)
Left: downwards.
Right: upwards.
Note: if you forget to cancel the di-
rection indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
Automatic "Follow me home"
lighting
With the ignition off, when you leave
your vehicle with the
automatic
switching on of the lights function
activated, the side lights and dipped
headlamps remain on for the select-
ed duration.
Activation:
switch off the engine,
"flash" the headlamps,
get out of the vehicle and lock it.
Deactivation:
"flash" the headlamps again,
get out of the vehicle and lock it.
To deactivate or activate
this function, go to the mul-
tifunction display configura-
tion menu.
The duration of the timed
period must also be set (15, 30,
60 seconds), via the multifunction
display configuration menu, except
in the case of the
monochrome
screen A for which it is pre-set.
Cancelling:
"flash" the headlamps,
get out of the vehicle and lock it.
Activation
Turn ring
A to the "AUTO" position.
The automatic lighting is accompa-
nied by a message on the multifunc-
tion display.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen, behind
the interior mirror. It is used for the
automatic switching on of the lights.
73
For vehicles fitted with halogen
bulbs, depending on the load in your
vehicle, adjusting the beam of your
headlamps is recommended.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
2. 5 people + maximum authorised
loads.
3. Driver + maximum authorised
loads.
Initial setting is position 0.
On vehicles with xenon bulbs:
when stationary, the system auto-
matically corrects the height of the
beam, whatever the load of the ve-
hicle. The driver is then assured of
having optimum lighting and not
causing a nuisance to other road
users.
In cases of malfunction,
the service warning light
comes on on the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction display.
The system places your headlamps
to the low position.
Do not touch the xenon bulbs.
Contact a PEUGEOT dealer.
Daytime lights*
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
* According to country.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually.
This warning light comes
on on the instrument panel.
MANUAL ADJUSTMENT OF
THE HEADLAMPS
AUTOMATIC HEADLAMP
ADJUSTMENT
74
Special position of the front
windscreen wiper
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement (See sec-
tion "Practical information - Chang-
ing a wiper blade").
To park the wipers after this has
been done, switch on the ignition and
operate the stalk.
Windscreen and headlamp wash
Pull the windscreen wiper stalk to-
wards you. The windscreen wash
then the windscreen wipers operate
for a fixed period.
The headlamp wash is also activated,
if the headlamps are on.
WINDSCREEN WIPER STALK
2
Fast wipe (heavy rain).
1
Normal wipe
(moderate rain).
I
Intermittent wipe.
0
Off.
AUTO Automatic or single wipe
(press downwards).
In the
Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In
AUTO mode, the wiping speed is
in proportion to the intensity of the
rainfall. The first press of the stalk
downwards activates the automatic
wipe.
Subsequent presses trigger a single
wipe.
Front windscreen wiper with
intermittent wipe
2 Fast wipe
(heavy rain).
1 Normal wipe
(moderate rain).
l
Intermittent wipe.
0 Off.
Single wipe
(press downwards).
In the
Intermittent position, the
wiping speed is in proportion to the
vehicle speed.
Front windscreen wiper with
automatic wipe
75
Automatic windscreen
wipers
In
AUTO mode, the windscreen wip-
ers operate automatically and
adapt
their speed to the intensity of the
rainfall.
Do not cover the rain sensor
located on the windscreen
behind the interior mirror.
When using an automatic car
wash, switch off the ignition.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
Activation
Activation of the function is accom-
panied by a message on the multi-
function display.
Rear windscreen wiper
To activate or deactivate
this function, go to the multi-
function display configura-
tion menu.
If there is a significant accumulation
of snow or ice and when using a bi-
cycle carrier on the tailgate (estate),
deactivate the automatic rear wiper
by going to the multifunction display
configuration menu.
Rear windscreen wash
Deactivation
Deactivation of the function is
accompanied by a message on the
multifunction display.
The function is deactivated when the
windscreen wipers stalk is moved to
position
I, 1 or 2.
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Turn ring
A past the first
A
A
notch; the windscreen wash
then the windscreen wiper
operate for a fixed period.
Turn ring
A to the first notch
for intermittent wiping.
When reverse gear is en-
gaged, if the windscreen
wipers are in operation, the
rear wiper starts.
The automatic windscreen
wipers function must be
reactivated if the ignition
has been switched off for
more than one minute, by press-
ing the stalk downwards.
75
Automatic windscreen
wipers
In
AUTO mode, the windscreen wip-
ers operate automatically and
adapt
their speed to the intensity of the
rainfall.
Do not cover the rain sensor
located on the windscreen
behind the interior mirror.
When using an automatic car
wash, switch off the ignition.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
Activation
Activation of the function is accom-
panied by a message on the multi-
function display.
Rear windscreen wiper
To activate or deactivate
this function, go to the multi-
function display configura-
tion menu.
If there is a significant accumulation
of snow or ice and when using a bi-
cycle carrier on the tailgate (estate),
deactivate the automatic rear wiper
by going to the multifunction display
configuration menu.
Rear windscreen wash
Deactivation
Deactivation of the function is
accompanied by a message on the
multifunction display.
The function is deactivated when the
windscreen wipers stalk is moved to
position
I, 1 or 2.
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Turn ring
A past the first
A
A
notch; the windscreen wash
then the windscreen wiper
operate for a fixed period.
Turn ring
A to the first notch
for intermittent wiping.
When reverse gear is en-
gaged, if the windscreen
wipers are in operation, the
rear wiper starts.
The automatic windscreen
wipers function must be
reactivated if the ignition
has been switched off for
more than one minute, by press-
ing the stalk downwards.
76
1. Front courtesy light
2. Map reading lights
Permanently off.
Permanently on.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- with the ignition off, 30 seconds af-
ter the last door is closed.
In this position, the courtesy
light comes on automati-
cally:
- when the vehicle is unlocked,
- when the key is removed from the
ignition,
- when a door is opened,
- when the vehicle location function
is used.
Different lighting times are available:
- with the ignition off or on, approxi-
mately 10 minutes,
- in economy mode, approximately
30 seconds,
- when the engine is running, no
limit.
With the ignition on, press
the corresponding switch.
COURTESY LIGHTS
77
3. Rear courtesy light
Note: on the saloon, the front cour-
tesy light (in the "permanently on"
position) forces the switching on of
the rear courtesy light if the switch is
in the central position.
To switch off the rear courtesy light,
place the switch in the "permanently
off" position.
In this position, the courtesy
light comes on automati-
cally:
- when the vehicle is unlocked,
- when the key is removed from the
ignition,
- when a door is opened,
- when the vehicle location function
is used.
Permanently off.
Permanently on when the
ignition is on (function not
available in economy mode).
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- with the ignition off, 30 seconds
after the last door is closed.
4. Rear reading lights (estate)
The reading light comes on:
- when the vehicle is unlocked,
- when the key is removed from the
ignition,
- when a door is opened,
- when the vehicle location function
is used.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- with the ignition off, 30 seconds
after the last door is closed.
With the ignition on (function not avail-
able in economy mode), press the
switch to obtain permanent lighting.
Press the switch again to switch the
reading light off.
78
With the ignition on, the mirror is
automatically lit up when the flap is
opened.
The front courtesy light and a spec-
tacles holder are fitted in the roof
console.
To open or close the spectacles holder,
press the recess in the cover.
The athermic windscreen has
two non-reflective zones located
either side of the base of the interior
mirror.
They are intended for affixing toll
cards and/or car park tickets.
SUN VISOR WITH ILLUMINATED
COURTESY MIRROR
THE ROOF CONSOLE
AREAS FOR TOLL CARDS/
CAR PARK TICKETS
79
INTERIOR LAYOUT
2. Front ashtray
Pull the lid to open the ashtray.
To empty it after opening, press the
tab and remove the ashtray.
3. Storage
4. 12 volt socket (100 W max)
This is a lighter type socket, fitted
with a cap. It is supplied with current
from the running position.
5. Door tray
6. Storage/Can holder
7. Coin storage
8. Waste container
To empty this, open it fully (past the
point of resistance) then pull on the
receptacle to remove it.
To refit, lock it in place on the cover.
It contains three sockets*
B for con-
necting video equipment.
The layout allows storage of a water
bottle, a pen, the vehicle handbook,
a pair of spectacles, tokens, etc.
* With colour screen only.
1. Glove box with cooling facility
This is fitted with a lock.
To open the glove box, lift the handle.
The glove box lights when the lid is
opened.
It has a ventilation nozzle that can
be closed
A, distributing the same
cooled air as the vents of the pas-
senger compartment.
80
When fitting the mat for the first time,
use only the fixings supplied in the
wallet attached.
When removing the mat on the driv-
er’s side:
- push the seat as far back as
possible,
- unscrew the fixings fully,
- remove the fixings, then the mat.
FITTING/REMOVING THE MAT
When refitting, position the
mat correctly and replace the
fixings by pressing them in.
Ensure that the mat is
secured correctly.
To prevent the mat from becoming
caught under the pedals:
- only use mats which are suited to
the fixings already present in the
vehicle. It is imperative that these
fixings are used.
- never fit one mat on top of another.
Lower the armrest to access the
storage shelf on the seat back.
Lift the lid. It contains a storage
tray as well as two can holders
and two pen holders.
REAR ARMREST
(SALOON AND ESTATE)
81
For further details, refer to the
operating manuals "Video kit
operation" and "VMA8582
7 inch LCD colour monitor".
ENTERTAINMENT SCREEN
KIT
This video assembly will enable the
rear passengers to pass the time
pleasantly while watching their fa-
vourite film or playing their favourite
game, by means, in particular, of the
connection of a DVD player or games
console to the central support, fitted
between the front seats.
The entertainment screen kit con-
sists of:
- a 16/9ths, 7 inch, LCD colour moni-
tor with direction adjustment in the
three axes,
- two high frequency, wireless, stereo
headphones,
- a removable support,
- three audio/video sockets on the
fixed base and in the glove com-
partment.
The monitor and the support can be
removed and stored, each in their
own protective cover.
The entertainment screen kit accepts
all types of audio/video source, PAL/
NTSC compatible, such as: DVD
player, camcorder, games console, ...
These sources are connected to the
three audio/video sockets,
AV1 in the
glove compartment or
AV2 on the
fixed base.
82
83
1. Rear parcel shelf
To remove the shelf:
- unhook the two strings,
- slightly raise the shelf, then remove
it.
The shelf can be stored:
- either behind the front seats,
- or behind the rear seat.
2. Hooks
3. Stowing rings
4. Luggage retaining net
Hooked onto the stowing rings, this
enables your luggage to be secured.
5. Open storage trays
6. 12 volt socket (100 W max)
This is a lighter type socket, installed
on the left-hand side of the parcel
shelf.
It is supplied from the "Running"
position.
BOOT LAYOUT (SALOON)
84
85
BOOT LAYOUT (ESTATE)
4. Boot floor and pillar stowing
rings
5. Rear seat stowing rings
6. Luggage retaining net
Secure the net hooks in the stowing
rings on the floor or on the folded
rear seat (two horizontal positions)
or secure the net hooks in the stow-
ing rings on the boot pillars and in the
floor rings at the rear of the boot (one
vertical position).
7. 12 volt socket (100 W max)
This is a lighter type socket, installed
on the load space cover left support.
It is supplied from the "Running" po-
sition.
8. High load retaining net fixings
The high load retaining net can be
installed behind the front or rear
seats.
Open the covers of the correspond-
ing upper fixings.
Fit the ends of the metal bar in these
fixings.
To install the high load retaining net:
- behind the front seats, lift the rear
seat cushion, hook the net straps
on the fixings then fold the rear
seat;
- behind the rear seat, hook the net
straps in the stowing rings on the
floor.
The rings are located directly below
the corresponding upper fixings.
Pull the two straps taut.
9. Grab handles and coat hooks
1. Load space cover
To install it:
- position the front ends of the cover
on its support and press gently to
put it in place,
- unfold the cover fully,
- position the rear ends of the cover
on its support and press gently to
put it in place.
To remove it:
- unclip the rear ends,
- fold the cover fully,
- unclip the front ends and remove
the cover.
To store it, slide it under the rear
seats (location
A).
2. Floor storage trays (2/3 - 1/3)
3. Storage nets
One of them contains the luggage re-
taining net.
86
Press the button, the direction indica-
tors flash.
They can operate with the ignition
off.
Press one of the spokes of the
steering wheel.
Automatic lighting of hazard
warning lights*
When braking in an emergency,
depending on the deceleration, the
hazard warning lights come on auto-
matically. They switch off automati-
cally the first time you accelerate.
It is also possible to switch them off
by pressing the button.
* According to country.
HORN
HAZARD WARNING LIGHTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст