Peugeot 307 Break (2007 year). Instruction — part 2
20
Engine oil pressure
warning light*
Linked to the central
STOP
warning light.
If it comes on with the engine run-
ning, it is accompanied by an audible
signal and a message on the multi-
function display.
Stop immediately.
If there is a lack of oil in the lubrica-
tion circuit, top up the level.
Contact a PEUGEOT dealer without
delay.
Battery charge warning
light*
This comes on for a few
seconds each time the igni-
tion is switched on.
If it comes on with the engine run-
ning, it is accompanied by an audible
signal and a message on the multi-
function display.
According to country, this warning
light may be replaced by the service
warning light.
It can indicate:
- faulty operation of the charging cir-
cuit,
- loose battery or starter terminals,
- a cut or slack alternator belt,
- an alternator fault.
Contact a PEUGEOT dealer.
Low fuel level
warning light
This comes on for a
few seconds each
time the ignition is
switched on.
When this light comes on with the en-
gine running, it is accompanied by an
audible signal and a message on the
multifunction display.
When the warning light comes on, you
have enough fuel left to drive approxi-
mately
30 miles (50 km). The tank
capacity is approximately 60 litres.
Passenger air bag
disarmed indicator light*
This comes on for a few
seconds each time the igni-
tion is switched on.
If the passager air bag is disarmed,
the indicator light remains on.
In all cases, if the indicator light flash-
es, contact a PEUGEOT dealer.
Diesel pre-heat light
This comes on for a few
seconds each time the igni-
tion is switched on.
Wait until it goes out before trying the
starter.
Engine oil pressure warning*
Linked to the central
STOP warning
light.
When the engine is running, the en-
gine oil pressure warning message is
accompanied by an audible signal.
Stop immediately.
If there is a lack of oil in the lubrica-
tion circuit, top up the level.
Contact a PEUGEOT dealer as soon
as possible.
* According to country.
Air bag warning light
This comes on for a few
seconds each time the igni-
tion is switched on.
Illumination of this warning light, with
the engine running, is accompanied
by an audible signal and a message
on the multifunction display indicat-
ing:
- a fault in the front air bags,
or
- a fault in the side air bags or curtain
air bags.
Contact a PEUGEOT dealer.
21
Coolant temperature indicator
Engine oil temperature gauge
When the needle is in zone
A, the
temperature is correct.
When the needle is in zone
B, the
temperature is too high. The central
STOP warning light flashes, accom-
panied by an audible signal and a
message on the multifunction dis-
play.
You must stop immediately.
Warning: wait for the engine to cool
before topping up the level.
The cooling system is pressurised.
In order to avoid any risk of scalding,
unscrew the cap two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level.
Contact a PEUGEOT dealer.
When the engine is running, this indi-
cates the oil temperature.
The temperature is too high if the
maximum graduation is reached.
You must stop immediately.
Contact a PEUGEOT dealer.
Park
Automatic gearbox lever
positions indicator
Reverse
Neutral
Drive
Manual mode:
1st gear engaged
2nd gear engaged
3rd gear engaged
4th gear engaged
5th gear** engaged
6th gear** engaged
** According to model.
22
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information re-
lating to the cruise control or speed
limiter, when either of these is acti-
vated (see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since
the last service.
Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
user’s driving habits.
INSTRUMENT PANEL DISPLAY
In the event of under-revving or over-
revving, the gear selected flashes for
a few seconds, then the actual gear
engaged is displayed.
This comes on when the
"SPORT" programme on
the automatic gearbox is se-
lected.
This comes on when the
"SNOW" programme on the
automatic gearbox is selected.
Automatic gearbox indicator
lights
"SNOW" indicator light
This is displayed if a gear is
not engaged correctly (selec-
tor between two positions).
"SPORT" indicator light
Invalid value during manual
operation
23
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display indi-
cates the number of miles [kilometres]
(rounded off) remaining until the next
service.
Example: 4,800 miles/km remain
before the next service. For five sec-
onds after the ignition is switched on,
the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.
The service is overdue.
The spanner flashes for 5 seconds
after the ignition is switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit. The display indi-
cates the total and trip distance.
Note: the spanner may also come on
if more than two years have elapsed
since the last service.
The distance remaining to
the next service is less than
500 miles (1,000 km).
Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
24
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows
"=0", re-
lease the button; the spanner disap-
pears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least five
minutes, otherwise the zero re-set
will not be registered.
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
information.
Oil level correct
Oil level gauge fault
Flashing of
"OIL --"
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Flashing of
"OIL",
linked with the serv-
ice warning light,
accompanied by an
audible signal and
a message on the
multifunction display, indicates a lack of
oil which could damage the engine.
If the lack of oil is confirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.
Lack of oil
Dipstick
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up the
level via the oil filler cap,
using the type of oil suit-
ed to your engine.
A = max.
B = min.
Service indicator zero re-set
22
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information re-
lating to the cruise control or speed
limiter, when either of these is acti-
vated (see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since
the last service.
Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
user’s driving habits.
INSTRUMENT PANEL DISPLAY
In the event of under-revving or over-
revving, the gear selected flashes for
a few seconds, then the actual gear
engaged is displayed.
This comes on when the
"SPORT" programme on
the automatic gearbox is se-
lected.
This comes on when the
"SNOW" programme on the
automatic gearbox is selected.
Automatic gearbox indicator
lights
"SNOW" indicator light
This is displayed if a gear is
not engaged correctly (selec-
tor between two positions).
"SPORT" indicator light
Invalid value during manual
operation
22
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information re-
lating to the cruise control or speed
limiter, when either of these is acti-
vated (see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since
the last service.
Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
user’s driving habits.
INSTRUMENT PANEL DISPLAY
In the event of under-revving or over-
revving, the gear selected flashes for
a few seconds, then the actual gear
engaged is displayed.
This comes on when the
"SPORT" programme on
the automatic gearbox is se-
lected.
This comes on when the
"SNOW" programme on the
automatic gearbox is selected.
Automatic gearbox indicator
lights
"SNOW" indicator light
This is displayed if a gear is
not engaged correctly (selec-
tor between two positions).
"SPORT" indicator light
Invalid value during manual
operation
23
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display indi-
cates the number of miles [kilometres]
(rounded off) remaining until the next
service.
Example: 4,800 miles/km remain
before the next service. For five sec-
onds after the ignition is switched on,
the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.
The service is overdue.
The spanner flashes for 5 seconds
after the ignition is switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit. The display indi-
cates the total and trip distance.
Note: the spanner may also come on
if more than two years have elapsed
since the last service.
The distance remaining to
the next service is less than
500 miles (1,000 km).
Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
24
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows
"=0", re-
lease the button; the spanner disap-
pears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least five
minutes, otherwise the zero re-set
will not be registered.
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
information.
Oil level correct
Oil level gauge fault
Flashing of
"OIL --"
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Flashing of
"OIL",
linked with the serv-
ice warning light,
accompanied by an
audible signal and
a message on the
multifunction display, indicates a lack of
oil which could damage the engine.
If the lack of oil is confirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.
Lack of oil
Dipstick
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up the
level via the oil filler cap,
using the type of oil suit-
ed to your engine.
A = max.
B = min.
Service indicator zero re-set
25
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the minimum (or maxi-
mum) setting, release the button then
press it again to increase (or reduce)
the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Trip recorder zero reset
button
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Lighting rheostat
26
TRIP COMPUTER
Press the button, located at the
end of the
wipers stalk, to display
the various items of trip computer
data in succession.
The trip computer data is the follow-
ing:
System which provides current infor-
mation concerning the route travelled
(range, consumption, ...).
Press the control for more than
two seconds to reset the distance
travelled, the average consump-
tion and the average speed to
zero.
Monochrome screen A
Zero reset
Data displays
- the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.
27
- the current information
tab with:
- the range,
- the current
consumption,
- the distance
remaining to be
travelled,
Colour screen
Route zero reset
Monochrome screen C
Press the button, located at the
end of the
wipers stalk, to display
the various trip computer tabs in
succession:
Data displays
When the route required is dis-
played, press the control for more
than two seconds.
- the route
"1" tab with:
- the distance
travelled,
- the average
consumption,
- the average speed,
for the first route.
- the route
"2" tab with:
- the distance
travelled,
- the average
consumption,
- the average speed,
for the second route.
Routes
"1" and "2" are independent
but their use is identical.
Route
"1" permits, for example, daily
calculations, and route
"2" monthly
calculations.
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, consumption, …).
28
Distance remaining to be
travelled
(km or miles)
This is the distance remain-
ing to be travelled to the final destina-
tion. It is either calculated instantly by
the navigation system if guidance is
activated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed
(km/h or mph)
This is the average speed
calculated since the last trip
computer zero reset (ignition
on).
Range
(km or miles)
This indicates the number
of miles (or kilometres)
which can still be travelled with the
fuel remaining in the tank in relation
to the average consumption over the
last few miles (kilometres) travelled.
Current consumption
(l/100 km or km/l or mpg)
This is the average quantity
of fuel consumed over the
last few seconds.
Average consumption
(l/100 km or km/l or mpg)
This is the average quan-
tity of fuel consumed since
the last trip computer zero reset.
Distance travelled
(km or miles)
This indicates the dis-
tance travelled since the
last trip computer zero
reset.
A few definitions…
When the range falls below 20 miles
(30 km), dashes are displayed. After
filling with at least 5 litres of fuel, the
range is recalculated and is displayed
when it exceeds 60 miles (100 km).
If dashes are displayed con-
tinuously while driving in
place of the digits, contact a
PEUGEOT dealer.
This function is only displayed
from 20 mph (30 km/h).
This figure may increase fol-
lowing a change of driving
style or relief, resulting in a
significant change in the cur-
rent consumption.
29
Screen C
Press the
"MENU" button to gain
access to the general menu.
Press the arrows, then the
"OK"
button to select the
"Trip compu-
ter" menu.
On the
"Trip computer" menu,
select one of the following appli-
cations:
Warnings log
This summarises the active warning
messages, displaying them in suc-
cession on the multifunction display.
Status of the functions
This summarises the active or inac-
tive status of the functions present on
the vehicle.
Enter the distance to the
destination
This enables you to enter an approx-
imate value for the distance to the
final destination.
"TRIP COMPUTER" MENU
System which provides general infor-
mation concerning the status of certain
equipment with which your vehicle is
equipped, such as the warnings log,
the status of the functions...
"DIAGNOSTICS" MENU
On the
"Diagnostics" menu, se-
lect one of the following applica-
tions:
Colour screen
Press the
"MENU" button to gain
access to the general menu.
Turn the dial and press it to select
the
"Diagnostics" menu.
30
Presentation
This displays the following informa-
tion:
- the time,
- the date,
- the outside temperature* (this
flashes if there is a risk of ice),
- the status of the accesses (doors,
boot, ...),
- the warning messages (e.g.: "Emis-
sion control system faulty") or infor-
mation messages (e.g.: "Auto lights
on"), displayed temporarily, can be
cleared by pressing the
"ESC" but-
ton,
- the trip computer (see correspond-
ing section).
MONOCHROME DISPLAY A
(without RD4 audio equipment)
Parameter configuration
There are three display control but-
tons:
-
"ESC" to abandon the operation in
progress,
-
"MENU" to scroll through the menus
or sub-menus,
-
"OK" to select the menu or sub-
menu required.
General menu
Press the
"MENU" button to scroll
through the various menus of the
general menu:
- vehicle configuration,
- options,
- display settings,
- languages,
- units.
Press the
"OK" button to select the
menu required.
* With air conditioning only.
31
Vehicle configuration
Once the "Vehicle configuration"
menu has been selected, you can
activate or deactivate the following
equipment:
- wiper linked with reverse gear (re-
fer to the "Visibility" section),
- "follow-me-home" lighting (refer to
the "Visibility" section),
- parking assistance (refer to the
"Driving" section).
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
Languages
Once the "Languages" menu has
been selected, you can change
the language used by the display
(Français, Italiano, Nederlands, Por-
tugues, Portugues-Brasil, Deutsch,
English, Espanol).
Display settings
Once the "Display settings" menu
has been selected, you can gain ac-
cess to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Units
Once the "Units" menu has been se-
lected, you can change the units of
the following parameters:
- temperature (°C or °F),
- fuel consumption (l/100, mpg or
km/l).
Once you have selected a setting,
press the
"OK" button to change its
value.
Wait for approximately ten sec-
onds without any action to allow the
changed data to be recorded or press
the
"ESC" button to cancel.
The display then returns to the nor-
mal display.
For safety reasons, configu-
ration of the multifunction
displays by the driver must
take place when stationary.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст