Alfa Romeo Stelvio (2018 year). Manual — part 53
Overfilling the brake fluid reservoir can
result in spilling brake fluid on hot engine
parts, causing the brake fluid to catch fire.
Brake fluid can also damage painted and
vinyl surfaces, care should be taken to avoid
its contact with these surfaces.
Do not allow petroleum based fluid to
contaminate the brake fluid. Brake seal
components could be damaged, causing
partial or complete brake failure.This could
result in a collision.
Automatic Transmission
Use only a transmission oil with the
characteristics indicated in "Fluids and
Lubricants" in "Technical Specifications".
Special Additives
Do not use any type of additive with the
automatic transmission oil.The
automatic transmission oil is a product
designed specially for this vehicle and its
performance may be compromised
through the use of further additives.
Caution!
Do not use chemical flushes in your
transmission as the chemicals can damage
your transmission components. Such
damage is not covered by the New Vehicle
Limited Warranty.
Frequency of Oil Changes
In normal vehicle operating conditions, it
is not necessary to change the
transmission oil.
Caution!
If a transmission fluid leak occurs, visit an
authorized dealer immediately. Severe
transmission damage may occur. An
authorized dealer has the proper tools to
adjust the fluid level accurately.
Replacing The Battery
If necessary, replace the battery with
another battery with the same
specifications. It is advised to contact an
authorized dealer for replacement.
Follow the battery manufacturer's
instructions for maintenance.
RAISING THE VEHICLE
If the vehicle requires lifting, visit an
authorized dealer which is equipped with
shop jacks or jack arms.
The vehicle lifting points are marked on
the side skirts with the
symbols.
0434132124US
Vehicle Lift Point Locations
225
TIRES
Tire Safety Information
Tire safety information will cover aspects
of the following information:Tire
Markings,Tire Identification Numbers,
TireTerminology and Definitions,Tire
Pressures, andTire Loading.
Tire Markings
Note:
P (Passenger) — Metric tire sizing is
based on U.S. design standards.
P-Metric tires have the letter “P” molded
into the sidewall preceding the size
designation. Example: P215/
65R15 95H.
European — Metric tire sizing is
based on European design standards.
Tires designed to this standard have the
tire size molded into the sidewall
beginning with the section width.The
letter "P" is absent from this tire size
designation. Example: 215/65R15 96H.
LT(LightTruck) — Metric tire sizing is
based on U.S. design standards.The size
designation for LT-Metric tires is the
same as for P-Metric tires except for the
letters “LT” that are molded into the
sidewall preceding the size designation.
Example: LT235/85R16.
Temporary spare tires are designed
for temporary emergency use only.
Temporary high pressure compact spare
tires have the letter “T” or “S” molded
into the sidewall preceding the size
designation. Example:T145/
80D18 103M.
High flotation tire sizing is based on
U.S. design standards and it begins with
the tire diameter molded into the
sidewall. Example: 31x10.5 R15 LT.
0601085395US
Tire Markings
1 — U.S. DOT
Safety Standards
Code (TIN)
4 — Maximum
Load
2 — Size
Designation
5 — Maximum
Pressure
3 — Service
Description
6 —Treadwear,
Traction and
Temperature
Grades
226
SERVICING AND MAINTENANCE
Tire Sizing Chart
EXAMPLE:
Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT
P
= Passenger car tire size based on U.S. design standards, or
"
.
blank
.
"
= Passenger car tire based on European design standards, or
LT
= Light truck tire based on U.S. design standards, or
Tor S
=Temporary spare tire or
31
= Overall diameter in inches (in)
215, 235, 145
= Section width in millimeters (mm)
65, 85, 80
= Aspect ratio in percent (%)
Ratio of section height to section width of tire, or
10.5
= Section width in inches (in)
R
= Construction code
"R" means radial construction, or
"D" means diagonal or bias construction
15, 16, 18
= Rim diameter in inches (in)
Service Description:
95
= Load Index
A numerical code associated with the maximum load a tire can carry
H
= Speed Symbol
A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions
The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle
loading, road conditions, and posted speed limits)
227
EXAMPLE:
Load Identification:
Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire:
XL
= Extra load (or reinforced) tire, or
LL
= Light load tire or
C, D, E, F, G
= Load range associated with the maximum load a tire can carry at a specified pressure
Maximum Load
– Maximum load indicates the maximum load this tire is designed to carry
Maximum Pressure
– Maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire
Tire Identification Number (TIN)
TheTIN may be found on one or both
sides of the tire; however, the date code
may only be on one side.Tires with white
sidewalls will have the fullTIN, including
the date code, located on the white
sidewall side of the tire. Look for theTIN
on the outboard side of black sidewall
tires as mounted on the vehicle. If theTIN
is not found on the outboard side, then
you will find it on the inboard side of the
tire.
EXAMPLE:
DOTMA L9 ABCD 0301
DOT
= Department ofTransportation
This symbol certifies that the tire is in compliance with the U.S. Department ofTransportation tire safety standards and is approved for highway
use
MA
= Code representing the tire manufacturing location (two digits)
L9
= Code representing the tire size (two digits)
ABCD
= Code used by the tire manufacturer (one to four digits)
228
SERVICING AND MAINTENANCE
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст