Alfa Romeo Giulia GTA (2022 year). Manual in english — page 9
143
SERVICE SCHEDULE
WARNING Once you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining the
frequency indicated in the plan by marking each operation with a dot or dedicated note. Warning: simply restarting the maintenance
from the start of the plan may cause the allowed interval to be exceeded for some operations!
Thousands of miles
9
18
27
36
45
54
63
72
81
90
Thousands of kilometres
15
30
45
60
75
90
105
120
135
150
Years
1
2
3
4
5
6
7
8
9
10
Check battery charge status with the proper instrument
Check tyre condition/wear and adjust pressure. Check Tyre Kit
recharge (where provided) conditions/expiry date
Check operation of lighting system (headlights, direction indicators,
hazard warning lights, boot, passenger compartment, glove
compartment, instrument panel warning lights, etc.)
Check and, if necessary, top up fluid levels (1)
Check exhaust emissions/smokiness
Check the supply/engine control and emissions systems operation
using the diagnosis equipment
Visually inspect condition of: exterior bodywork, underbody
protection, pipes and hoses (exhaust, fuel system, brakes), rubber
elements (gaiters, sleeves, bushes, etc.)
Check windscreen wiper blade position/wear
Check operation of the windscreen wiper/washer system and adjust
nozzles, if necessary
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
144
Thousands of miles
9
18
27
36
45
54
63
72
81
90
Thousands of kilometres
15
30
45
60
75
90
105
120
135
150
Years
1
2
3
4
5
6
7
8
9
10
Check cleanliness of hood and boot locks, cleanliness and lubrication
of linkage
Visually inspect conditions and wear of front disc brake pads and
operation of pad wear indicators
Visually inspect conditions and wear of rear disc brake pads and
operation of pad wear indicators
Visually inspect the condition and tensioning of the accessory drive
belt(s) (2)
Visually inspect the surface and edge of the carbon ceramic brake
discs
Change engine oil and replace oil filter
Spark plug replacement(3)
Replace accessory drive belt/s
(2)
Replace air cleaner cartridge (4)
Change the brake fluid
(5)
Replace brake pads/carbon ceramic brake discs
(6)
Replace passenger compartment filter (4)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
145
Thousands of miles
9
18
27
36
45
54
63
72
81
90
Thousands of kilometres
15
30
45
60
75
90
105
120
135
150
Years
1
2
3
4
5
6
7
8
9
10
Alfa Connect Box system battery replacement (where provided) (7)
(1) Always only use the liquids shown in the handbook for topping up after having checked that the system is not damaged.
(2) The maximum mileage is 60,000 km. The belt must be replaced every 4 years, regardless of distance travelled. If the vehicle is used in heavy
conditions (dusty areas, particularly harsh weather conditions, very low or very high temperatures for extended periods, urban driving, long periods
of idling), the maximum mileage is 30,000 km. The belt must be replaced every 2 years regardless of the mileage.
(3) The replacement must be performed according to mileage and regards of the elapsed time. The following are vital in order to ensure correct
operation and prevent serious damage to the engine: - only use spark plugs specifically certified for the engine itself of the same type and brand (see
the "Engine" paragraph in the "Technical Specifications" chapter); - strictly comply with the spark plug replacement intervals in the Service Schedule.
It is advisable to contact a Dedicated Alfa Romeo Dealership for plug replacement.
(4) If the vehicle is used in dusty areas, this cleaner should be replaced every 15,000 km.
(5) The brake fluid replacement has to be done every two years, irrespective of the mileage.
(6) The actual interval for changing the brake pads and the carbon ceramic brake discs depends on the car usage conditions and is signalled by the
warning light or message on the instrument panel. Use the diagnosis equipment to reset the warning light every time the discs are replaced.
(7) The battery in the Alfa Connect Box system must be replaced every 5 years, regardless of mileage.
(o) Recommended operations
(●) Mandatory operations
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
146
ENGINE COMPARTMENT
CHECKING LEVELS
137
09026S0001EM
1. Engine oil filler 2. Primary engine cooling reservoir plug 3. Brake fluid reservoir plug access cover 4. Windscreen/headlight washer
fluid reservoir cap 5. Secondary engine cooling reservoir plug 6. Engine oil level dipstick
-------------------------------------------------------------------------------------------------------------------------------------------------------------
147
ENGINE OIL
136)
32)
WARNING It is advisable to check the
engine oil level indication before long
journeys.
The engine oil level can be seen on the
instrument panel display every time the
engine is started, or on the Connect
system display using the "Vehicle
Information" widget.
Use the 6 segments on the display to
check that the oil level is between MIN
and MAX level.
1 segment
= MIN level
6 segments
= MAX level
If the oil level indication reaches the
first red mark, add oil through the filler
(1), considering that each segment
shown on the display corresponds to
approximately 0.055 UK gal (250 ml).
If the
symbol and the corresponding
message "Insufficient engine oil level"
light up on the display of the instrument
panel, top up 0.26 UK gal (1 litre) of
engine oil as soon as possible.
In case of oil change or top-up, check the
amount introduced using the dipstick.
The level must NEVER be over the MAX
line.
The oil level must be checked with
the dipstick with the engine warm
(temperature of about 198°F/90°C) and
after waiting for 5 minutes.
33)
WARNING Make sure not to add too
much engine oil when topping up. Engine
oil in excess may damage the engine.
Have the car checked. Never exceed the
MAX level when topping up engine oil.
It is advisable to check the oil level in
intermediate steps on the instrument
panel display. Check the oil level using
the dipstick.If the level is over the MAX
line on the dipstick, go to a dedicated
Alfa Romeo Dealership.
WARNING The oil level is not refreshed
immediately on the display of the
instrument panel after topping up.
Consequently, wait for the oil level to be
refreshed on the display following the
procedure described below.
Engine oil level manual checking
procedure
With the car on level ground, check that
the oil level is between the MIN and MAX
marks on the dipstick (6).
Take out the engine oil dipstick (6), clean
it with a lint-free cloth and reinsert it.
Extract the dipstick again and check that
the level is between the MIN and MAX
marks on it.
33)
WARNING The manual engine oil level
checking procedure must be carried out,
when necessary, on a cold engine only.
Never attempt to carry out the manual
engine oil checking procedure (using the
dipstick) with the engine hot. Contact
with the surrounding hot engine parts
could cause burns.
Refreshing of engine oil level
indication update on display
If a top-up has been necessary, proceed
as follows to ensure correct indication
of the engine oil level on the instrument
panel display:
with the car level, run the engine for
approximately 5 minutes (temperature
of approximately 198°F/90°C) and then
stop the engine;
wait for at least 5 minutes, turn the
ignition device to ON position without
starting the engine and wait for a few
seconds.
If the level indication is not refreshed
procedure just described, run the engine
as above again, stop the engine and
wait a further 5 minutes before starting
it again. If the indication is not updated
after the second start, contact the
Dedicated Alfa Romeo Dealership.
WARNING In normal working conditions,
the oil level indication is shown on the
instrument panel display. In the event
of an oil level sensor failure (condition
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
148
indicated by the
symbol appearing on
the instrument panel display), use the
oil dipstick in the engine compartment
EXCLUSIVELY for the time needed to
restore correct operation of the oil level
sensor, which must be performed at a
Dedicated Alfa Romeo Dealership.
Engine oil consumption
34)
4)
The maximum engine oil consumption
is usually 0.88 lb (400 grams every
620 miles (1000 km).
When the car is new, the engine needs
to be run in, therefore the engine oil
consumption can only be considered
stabilised after the first 3100 - 3700
miles (5000 - 6000 km).
ENGINE COOLANT
137)
35)
If the level is too low, unscrew the cap of
the reservoir and add the fluid described
in the "Technical Specifications" chapter.
WASHER FLUID FOR
WINDSCREEN/HEADLIGHTS
138) 139)
The windscreen and headlights washer
fluid reservoir (where available) is
equipped with a telescopic filler.
If the level is too low, lift the reservoir
cap (4) fig. 138 upwards and then lift the
filler, as shown in the figure, and add
the fluid described in the "Technical
Specifications" chapter. After having
topped up the fluid, arrange the filler
correctly and then press on the cap until
you hear it click.
NOTE The headlight washers are
activated every 10 activations of the
windscreen washer.
WARNING With a low fluid level
(indicated by the dedicated symbol
appearing on the instrument panel
display), the headlight washer system
does not work, even though the screen
washers continue to work.
138
09086S0666EM
BRAKE FLUID
Check that the fluid is at the max. level. If
the liquid level in the tank is insufficient,
contact a Dedicated Alfa Romeo
Dealership to have the system checked.
AUTOMATIC TRANSMISSION
ACTIVATION SYSTEM OIL
5)
The transmission control oil level should
only be checked at a Dedicated Alfa
Romeo Dealership.
BATTERY
140) 141) 142) 143)
36)
6)
The battery does not require the
electrolyte to be topped up with distilled
water. A periodic check carried out at
a Dedicated Alfa Romeo Dealership is,
however, necessary to check efficiency.
Follow the battery manufacturer's
instructions for maintenance.
Useful advice for extending the life of
your battery
To avoid draining your battery and make
it last longer, observe the following
instructions:
when you park the car, ensure that
the doors, boot and bonnet are closed
properly, to prevent any lights from
-------------------------------------------------------------------------------------------------------------------------------------------------------------
149
remaining on inside the passenger's
compartment;
switch off all roof lights inside the
car: the car is however equipped with a
system which switches all internal lights
off automatically;
do not keep accessories (e.g. Connect
system, hazard warning lights, etc.)
switched on for a long time when the
engine is not running;
before performing any operation on
the electrical system, disconnect the
negative battery cable.
If, after purchasing the car, you wish
to install electrical accessories
which require permanent electrical
supply (e.g. alarm, etc.) or accessories
which influence the electrical supply
requirements, contact a Dedicated Alfa
Romeo Dealership, whose qualified
staff will evaluate the overall electrical
consumption.
WARNING If the battery was
disconnected, do not start the engine
immediately after reconnecting the
terminals, but press the start button,
without operating the pedals, to turn on
the instrument panel and then start the
engine.
WARNING If the charge level remains
under 50% for a long time, the battery
is damaged by sulphation, reducing its
capacity and efficiency at start-up. The
battery is also more prone to the risk of
freezing (at temperatures of 14°F/-10°C).
Replacing the battery
If necessary, replace the battery with
another original battery with the same
specifications. Follow the battery
Manufacturer’s instructions for
maintenance.
WARNING It will not be possible to open
the boot with a key or by pressing the
button in the passenger compartment
when the battery is disconnected. So,
always extract the manual boot opening
strap before disconnecting the battery.
The procedure is described in the
"Prolonged vehicle inactivity" paragraph
in this chapter.
WARNING
136)
If the engine oil is being topped up, wait
for the engine to cool down before loosening
the filler cap, particularly for vehicles with
aluminium cap (where provided). WARNING:
risk of burns!
137)
The cooling system is pressurised.
If necessary, only replace the plug with
another original or the operation of the
system may be adversely affected. Do not
remove the reservoir plug when the engine is
hot: you risk scalding yourself.
138)
Do not travel with the windscreen
washer fluid reservoir empty: the
windscreen washer is essential for
improving visibility.
139)
Some commercial additives for
windscreen washer fluid are flammable.
The engine compartment contains hot
components which may start a fire.
140)
Battery fluid is poisonous and
corrosive. Avoid contact with the skin and
eyes. Keep open flames away from the
battery and do not use objects that might
create sparks: risk of explosion and fire.
141)
Using the battery with low fluid will
irreparably damage the battery and may
cause an explosion.
142)
If the car must remain unused for a long
time at a very low temperature, remove the
battery and take it to a warm place, to avoid
freezing.
143)
Always wear appropriate goggles to
protect your eyes when working on or near
the battery.
IMPORTANT
32)
The oil level must never exceed the MAX
mark.
33)
If the MAX mark is exceeded (last notch
on the right turns red) after the top-up, go
to a Dedicated Alfa Romeo Dealership as
soon as possible to have the oil in excess
removed.
34)
Always top up using engine oil of the
same specifications as that already in the
engine.
35)
Use a fluid of the same type as that
already present in the reservoir for any
topping up of the engine cooling system.
The fluid cannot be mixed with other types
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
150
of antifreeze fluids. In the event of topping
up with an unsuitable product, under no
circumstances start the engine and contact
a Dedicated Alfa Romeo Dealership.
36)
When you need to disconnect or remove
the battery, do not close the boot. In order
to avoid possible accidental closure, it is
recommended to place an obstacle (e.g.
a cloth) on the lock that would physically
avoid closure.
IMPORTANT
4)
Used engine oil and oil filters contain
substances which are harmful to the
environment. To change the oil and filters,
we advise you to contact a Dedicated Alfa
Romeo Dealership.
5)
Used transmission oil contains
substances that may be dangerous for the
environment. You are advised to contact a
Dedicated Alfa Romeo Dealership for oil
changes.
6)
Batteries contain substances which
are very harmful for the environment. For
battery replacement, contact a Dedicated
Alfa Romeo Dealership.
RECHARGING THE BATTERY
IMPORTANT NOTES
144) 145)
WARNING Before using the charging
device, always make sure that it is
appropriate for the installed battery,
with constant voltage (below 14.8 V) and
low amperage (maximum 15 A).
WARNING Recharge the battery in a well
ventilated environment.
WARNING Never charge or recharge a
frozen battery: it may explode because
of the hydrogen trapped inside the ice
crystals.
WARNING At all times while charging
or recharging the battery, make sure
that any sparks or open flames are kept
sufficiently far away from the battery.
WARNING Before using any devices to
charge or to maintain the charge of the
battery, carefully follow the instructions
provided with the device in order to
properly and safely connect it to the car
battery.
You can recharge the battery without
disconnecting the wires of the electrical
system of the car.
To reach the battery, remove the
access panel inside the luggage
compartment fig. 139;
139
09036S0001EM
remove the protective cover (1) fig. 140
and connect the positive cable terminal
of the charger (usually red) to the
positive terminal (+) of the battery;
connect the terminal of the negative
cable of the charger (usually black) to nut
(2) next to the negative terminal (-) of the
battery, as shown in fig. 140;
140
09036S0002EM
The car is equipped with an IBS
(Intelligent Battery Sensor), which is able
to measure the charge and discharge
-------------------------------------------------------------------------------------------------------------------------------------------------------------
151
voltage and calculate the charge level
and the general condition of the battery.
The sensor is placed next to the negative
terminal (-) of the battery.
For a correct charge/discharge
procedure, the charge voltage must go
through the IBS sensor.
Turn the charger on and follow the
instructions on the user's manual to
completely recharge the battery;
when the battery is charged, turn the
charger off before disconnecting it from
the battery;
first disconnect the black cable
terminal of the battery charger and then
the red cable terminal;
refit the protective cover of the
positive terminal of the battery
and the access cover to the battery
compartment.
WARNING If a "quick-type" battery
charger is used with the battery fitted
on the vehicle, before connecting it
disconnect both cables of the battery
itself. Do not use a "quick-type" battery
charger to provide the starting voltage.
37)
WARNING
144)
The process of charging or recharging
the battery produces hydrogen, a
flammable gas that can explode and cause
serious injury.
145)
When charging or recharging the
battery, always follow the precautions
listed.
IMPORTANT
37)
When you need to disconnect or remove
the battery, do not close the boot. Open the
boot manually if it is locked.
SERVICING PROCEDURES
146) 147) 148)
38) 39) 40) 41) 42) 43) 44)
AIR CONDITIONING SYSTEM
MAINTENANCE
45) 46)
To ensure the best possible
performance, the air conditioning
system must be checked and undergo
maintenance at a Dedicated Alfa Romeo
Dealership at the beginning of the
summer.
WARNING Do not use chemicals to clean
the air conditioning system, since the
internal components may be damaged.
This kind of damage is not covered by
warranty.
WINDSCREEN WIPER
Raising the windscreen wiper blades
("Service position" function)
The "Service position" function allows
the driver to replace the windscreen
wiper blades more easily. It is also
recommended to activate this function
when it is snowing and to make it easier
to remove any dirt deposits in the
area where the blades are normally
positioned, when washing.
Activation of the function
To activate this function, deactivate the
windscreen wiper (ring fig. 141 in position
O
) before setting the ignition device to
STOP.
This function can only be activated within
2 minutes of setting the ignition device
to STOP.
To activate this function, move the lever
upwards (unstable position) for at least
three seconds.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
152
141
09046S0001EM
Function deactivation
The function is deactivated if:
wait for longer than 2 minutes before
turning the ignition device to the STOP
position, after having raised the lever,
and starting the Service procedure in this
way;
the ignition device is taken to position
ON and the windscreen wiper control.
If, after using the function, the ignition
device is set back to ON with the blades
in a position other than rest position (at
the base of the windscreen), they will
only return to rest position following a
command given using the stalk (stalk
upwards, into unstable position) or when
a speed of 5 km/h is exceeded.
Replacing the windscreen wiper blades
Proceed as follows:
raise the wiper arm, press tab fig. 142
of the attachment spring and remove the
blade from the arm;
fit the new blade, inserting the tab in
the dedicated housing in the arm and
checking that it is locked;
lower the wiper arm onto the
windscreen.
142
09046S0002EM
WARNING Do not operate the
windscreen wiper with the blades lifted
from the windscreen.
Windscreen washer
The window washer nozzles are fixed.
If there is no jet of fluid, firstly check
that there is fluid in the reservoir (see
contents of “Engine compartment”
paragraph in this chapter).
Then check that the nozzle holes are not
clogged; use a needle to unblock them if
necessary.
WARNING
146)
The air intake system (air cleaner,
rubber hoses, etc.) can be a protection in
the case of blowbacks from the engine. DO
NOT REMOVE this system unless you need
to carry out repair or maintenance. Before
starting the engine, ensure that the system
has not been removed: failure to observe
this precaution may result in serious injury.
147)
Exhaust emissions are very dangerous,
and may be lethal. They contain carbon
monoxide, a colourless, odourless gas which
can cause fainting and poisoning if inhaled.
148)
The exhaust system may reach high
temperatures and may cause a fire if the
car is parked on flammable material. Dry
grass or leaves can also catch fire if they
come into contact with the exhaust system.
Do not park or use the car in a place in which
the exhaust system might come into contact
with flammable material.
IMPORTANT
38)
Incorrect servicing of the car or failure
to carry out operations or repairs (when
necessary) may lead to more expensive
repairs, damage to other components
or have a negative impact on the car
performance. Have any malfunction
inspected immediately by a Dedicated Alfa
Romeo Dealership.
39)
The car is filled with fluids which are
optimised or protecting its performance
and life and extending service intervals.
Do not use chemicals for washing these
components since they may damage the
-------------------------------------------------------------------------------------------------------------------------------------------------------------
153
engine, the transmission or the climate
control system. This damage is not covered
by the car’s warranty. If any component
needs to be washed due to malfunctioning,
use only the specific liquid for that
procedure.
40)
An excessive or insufficient amount of
oil inside the base is extremely damaging
to the engine. Make sure it is always at an
adequate level.
41)
Vehicles equipped with catalytic
converter must be fuelled only with
unleaded petrol. Leaded petrol would
permanently damage the catalytic
converter and eliminate its ability to reduce
polluting emissions, seriously compromising
the engine performance, which would
be irreparably damaged. If the engine
does not work correctly, especially if it
starts irregularly or if there is a reduction
of its performance, immediately go to
a Dedicated Alfa Romeo Dealership.
Prolonged and faulty operation of the
engine may cause overheating of the
converter and, as a consequence, possible
damage to the converter and the vehicle.
42)
Using transmission fluid different from
that approved may compromise the quality
of gear changes and/or cause vibration of
the transmission.
43)
It is recommended to have the car
serviced by a Dedicated Alfa Romeo
Dealership. When carrying out normal
periodic operations and small servicing
interventions personally on the vehicle, it is
recommended to use suitable equipment,
genuine spare parts and the necessary
fluids. Do not carry out any interventions if
you do not have the necessary experience.
44)
When you need to disconnect or remove
the battery, do not close the boot. In order
to avoid possible accidental closure, it is
recommended to place an obstacle (e.g.
a cloth) on the lock that would physically
avoid closure.
45)
Always require the use of only
compressor coolants and lubricants
approved and suitable for the specific air
conditioning system fitted on the car. Some
non-approved coolants are flammable and
may explode, with the risk of injuries. The
use of non-approved coolants or lubricants
may adversely affect system efficiency,
leading to expensive repairs.
46)
The air conditioner system contains
coolant under high pressure: to avoid
injuries to people or damage to the system,
any coolant addition or repair that requires
to disconnect the cables must be carried out
by a Dedicated Alfa Romeo Dealership.
RAISING THE CAR
If the car needs to be jacked up, go to a
Dedicated Alfa Romeo Dealership which
is equipped with shop jacks or jack arms.
The vehicle lifting points are marked on
the side skirts with the symbols
(see
illustration in fig. 143).
143
08066S0034EM
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
154
WHEELS AND TYRES
SAFETY INFORMATION
Before embarking on a long trip, and
every two weeks, check the tyre inflation
pressure. Check the tyres when cold.
It is normal for the pressure to
increase when the vehicle is used due
to tyre heating; for the correct tyre
inflation pressure, see the "Rims and
Tyres" paragraph in the "Technical
specifications" chapter.
Incorrect pressure causes abnormal tyre
wear fig. 144:
1 -
normal pressure
: tread evenly worn;
2 -
low pressure
: tread particularly worn
at the edges;
3 -
high pressure
: tread particularly worn
in the centre.
The tyres must be replaced when the
tread reaches the minimum thickness
reference on the tyres themselves.
144
09066S0001EM
GENERAL INFORMATION
149) 150) 151)
Take the following precautions to
prevent damage to the tyres:
avoid braking suddenly, racing starts
and violent impact against the curb,
potholes or other obstacles and driving
for extended periods on uneven road
surfaces;
periodically check that the tyres
have no cuts in the side wall, abnormal
swelling or irregular tread wear;
avoid travelling with the car
overloaded. If a tyre is punctured, stop
immediately and change it;
tyres age even if they are not used
much. Cracks in the tread and on the
sidewalls are a sign of ageing. In any
event, have the tyres checked by
specialised technicians if they have been
fitted for longer than 1 year.
in the case of replacement, always fit
new tyres, avoiding those of unknown
origin.
RIMS AND WHEELS
For the type of wheel rims and tyres
fitted on the vehicle see the "Rims and
Tyres" paragraph in the "Technical data"
chapter.
SNOW CHAINS
47)
Snow chains may be fitted on the 255/30
R20 rear tyres (winter tyre size), with
size "255" tyres fitted at both front and
rear. Avoid using traditional chains as
they can damage the braking system
if not installed correctly, thereby
compromising the car’s safety.
We strongly advise using the following
chains and the equipment offered by the
Dedicated Alfa Romeo Dealership.
Warnings
The use of snow chains should be in
compliance with local regulations of
each country. In certain countries, tyres
marked with code M+S (Mud and Snow)
and the
symbol are considered as
winter equipment.
Snow chains may be applied only to the
rear wheel tyres.
Check the tension of the snow chains
after the first few feet/meters have
been driven.
WARNING Using snow chains with tyres
with non-original dimensions is not
permitted and may damage the car.
WARNING Using different size or
type (M+S, snow, etc.) tyres between
front and rear axle may adversely
affect car driveability, with the risk of
-------------------------------------------------------------------------------------------------------------------------------------------------------------
155
losing control of the car and resulting
accidents.
RECOMMENDATIONS REGARDING
THE USE OF Michelin Pilot Sport CUP2
Connect TYRES
Michelin Pilot Sport CUP2 Connect tyres
are mainly for use for track driving (they
are semi slick tyres) and perform best
when driving on dry tracks. However,
this type of tyre meets current legal
requirements and its use on roads and
motorways is also permitted.
Michelin Pilot Sport CUP2 Connect
tyres perform best when driving on dry
tracks. When driving on wet tracks or
roads there is a risk of aquaplaning, a
very common risk with racing tyres,
which increases as the tyres become
worn. You should therefore ensure that
your driving style is suited to the road
surface/track conditions, reduce speed,
and not deactivate the driver assistance
systems.
Michelin Pilot Sport CUP2 Connect tyres
should be fitted to all 4 wheels to give
the car the correct stability.
Warnings
If Michelin Pilot Sport CUP2 Connect
tyres are not used for a lengthy period
of time, remove them from the car and
reduce the pressure to half the normal
value (for tyre inflation pressures, refer
to the “Cold tyre inflation pressure” table
in the “Technical Data” chapter).
Stow tyres in a clean place with dry
air. Do not expose them to direct
contact with sunlight or sources
of zone (electrical devices and/or
chemicals); also ensure that the
ambient temperature is over 0°C,
(32°F) as recommended by the tyres’
Manufacturer.
Do not use or stow Michelin Pilot Sport
CUP2 Connect tyres in a location with
ambient temperature below -10°C
(14°F). The tyres may degrade below
this temperature, impairing their
performances. There is also the risk of
cracks or damage to the tyres’ surface,
preventing their correct use and reducing
driving safety.
NEVER use damaged tyres: if in doubt
contact a Dedicated Alfa Romeo
Dealership.
If Michelin Pilot Sport CUP2 Connect
tyres have been used for track driving for
a lengthy period of time, they may wear
more rapidly. Therefore take great care
to ensure they have not been damaged
by collisions with kerbs and on the edge
of the track.
Tyres should be visually inspected at the
end of every track lap, and always before
starting a new lap.
If tyres frequently collide with track
kerbs (or in case of prolonged high-speed
driving) their inside and outside surfaces
should be inspected. For this procedure,
tyres must be removed from the car
and inspected by qualified staff able to
assess any damage to them.
TYRE DURATION ADVICE
The front and rear tyres are subject
to different loads and stress due to
steering, manoeuvres and braking. For
this reason they are subject to uneven
wear.
WARNING Crossing the tyres is not
advised, so placing a tyre on a different
axle on the other side of the car is
impossible.
WARNING No type of tyre rotation is
permitted since the car is fitted with
differentiated tyres (different size tyres
on front and rear axles).
In the case of irregular tyre wear, identify
the cause and correct it as soon as
possible, by contacting a Dedicated Alfa
Romeo Dealership.
WARNING
149)
The road holding qualities of the
car also depend on the correct inflation
pressure of the tyres.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
156
150)
If tyre pressure is too low, it may
overheat and be severely damaged as a
result.
151)
Do not repaint alloy wheel rims at
temperatures higher than 212°F (100°C). The
mechanical features of the wheels could be
compromised.
IMPORTANT
47)
Keep your speed down when snow
chains are fitted; do not exceed 50 km/h.
Avoid potholes, do not drive over steps or
pavements and do not drive long distances
over roads without snow, to avoid damaging
both your car and the road surface.
BODYWORK
PROTECTION AGAINST ATMOSPHERIC
AGENTS
The car is equipped with the best
available technological solutions to
protect the bodywork against corrosion.
These include:
painting products and systems which
give the car resistance to corrosion and
abrasion;
use of galvanised (or pre-treated) steel
sheets, with high resistance to corrosion;
spraying of plastic parts, with a
protective function in the more exposed
points: underdoor, inner wing, edges, etc.;
use of “open” boxed sections to
prevent condensation and pockets
of moisture which could favour the
formation of rust inside;
use of special films to protect against
abrasion in exposed areas (e.g. rear wing,
doors, etc.).
BODY AND UNDERBODY WARRANTY
Your car is covered by warranty against
perforation due to rust of any original
element of the structure or bodywork.
For the general terms of this warranty,
refer to the Warranty Booklet.
PRESERVING THE BODYWORK
Paintwork
48) 49)
7)
Touch up abrasions and scratches
immediately to prevent the formation of
rust.
Maintenance of paintwork consists of
washing the car: the frequency depends
on the conditions and environment
where the car is used. For example, it is
advisable to wash the car more often in
areas with high levels of atmospheric
pollution or salted roads.
Some parts of the vehicle may be
covered with a matt paint which, in order
to be maintained intact, requires special
care: see the instructions in the warning
at the end of this paragraph.
50)
To correctly wash the car, follow these
instructions:
if high pressure jets or cleaners are
used to wash the car, keep a distance
of at least 16 inches (40 cm) from the
bodywork to avoid damage or alteration.
Build up of water could cause damage to
the car in the long term;
to facilitate removal of any dirt in the
area where the brushes are normally
placed, the windscreen wipers should
be placed vertical (Service Position).
For more information refer to the
“Maintenance procedures” paragraph in
this chapter;
wash the bodywork using a low
pressure jet of water if possible;
wipe a sponge with a slightly soapy
solution over the bodywork, frequently
rinsing the sponge;
rinse well with water and dry with a jet
of air or a chamois leather.
Dry the less visible parts (e.g. door
frames, bonnet, headlight frames, etc.)
with special care, as water may stagnate
more easily in these areas. Do not wash
the car after it has been left in the sun or
with the bonnet hot: this may alter the
shine of the paintwork.
Exterior plastic parts must be cleaned in
the same way as the rest of the car.
If you wish to wash the car in a car wash
which moves it, proceed as follows:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
157
make sure that the car is on a flat
surface and that automatic engagement
of the electric parking brake when the
engine is switched off is disabled (for
how to disable it, refer to the "Electric
parking brake" section in the "Starting
and driving" chapter);
with the car stationary, the gear in N
(Neutral) and the brake pedal up: press
the start button. The car will remain in
N (Neutral) for 15 minutes, after which P
(Park) mode will be activated.
Avoid parking under trees; the resin
dropped by trees makes the paintwork
go opaque and increases the possibility
of corrosion.
Care and maintenance of the Alfa
Romeo logo badge / central wheel nut /
ring
The following are recommended for care
and maintenance of the Alfa Romeo logo
badge / central wheel nut / ring:
do not use acid or alkaline detergents
which may damage the parts’ surface
finish;
if detergents are used, read the
instructions and warnings provided by
the producer;
do not use brushes or any other tool
which may scratch the components;
rinse with plenty of water;
before washing the car in a car wash,
make sure that the brushes are soft.
Windows
Use specific detergents and clean cloths
to prevent scratching or altering the
transparency.
WARNING Wipe the rear window inside
gently with a cloth following the direction
of the filaments to avoid damaging the
heating device.
GTAm versions
On GTAm versions, proceed as follows
to clean the Lexan® main and door rear
windows:
use a solution of delicate neutral soap
(or compatible household detergent) and
warm water and remove all traces of dirt
with a soft cloth or sponge. Rinse with
plenty of cold water and dry with a damp,
clean chamois leather to help to prevent
the formation of water marks.
any scratches or abrasions cannot be
corrected. Any type of treatment will
only worsen the situation;
DO NOT rub with dry or dirty rags;
DO NOT use abrasive or highly alkaline
detergents; the surface should be
cleaned with isopropyl alcohol;
DO NOT use scouring pads, squeegees,
razor blades or other sharp tools;
DO NOT clean Lexan® parts in hot
sunlight or in high ambient temperature
conditions;
DO NOT clean surfaces with your
hands.
WARNING Before starting cleaning,
remove any metal objects you are
wearing, such as watches, bracelets,
rings, buttons, zips, etc. Do not apply
glues or adhesives, stickers, decals,
labels, etc. to the inside surface; the
solvent in the glue damages the Lexan ®
component.
Headlights
Use a soft cloth soaked in water and
detergent for washing cars.
WARNING Never use aromatic
substances (e.g. petrol) or ketones (e.g.
acetone) for cleaning the plastic lenses
of the headlights.
WARNING When cleaning the car with
a pressure washer, keep the water jet
at least 8 in (20 cm) away from the
headlights.
VERSIONS WITH STICKERS
(where provided)
WARNING Due to their hand-crafted
nature, the car or car parts covered,
decorated and/or customised with
stickers must be cleaned and washed
exclusively by hand. The use of high-
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
158
pressure cleaners or roller brushes is not
recommended.
The use of solvents, waxes, detergents
or similar products is not recommended
for the care of the car as they could
damage the stickers or cause them to
detach.
The use of such washing or cleaning
instruments and methods will therefore
invalidate the warranty.
NOTE We recommend using mild
products for cleaning the car.
WARNING Any water marks on stickers
should be removed by wetting again and
drying with a non-abrasive soft cloth.
CARBON AERODYNAMIC
APPENDAGES
WARNING To avoid damaging carbon
aerodynamic appendages on the car,
we recommend washing them by hand.
In fact, aerodynamic appendages must
be treated with special care to avoid
damaging them.
ENGINE COMPARTMENT WASHING
51)
If the engine compartment is washed (at
low pressure, e.g. in very dusty areas),
this must be done with the engine cold
and with ignition device turned to STOP.
Take care not to direct the water
jet straight at the electronic control
modules or the wiper motors. Have this
operation performed by a specialised
workshop. After washing, check that the
various protective components (e.g.
rubber guards and caps) have not been
removed or damaged.
IMPORTANT
48)
In order to preserve the appearance of
the paint abrasive products and/or polishes
should not be used for cleaning the car.
49)
Abrasive products and/or polishes
should not be used for cleaning the car. Bird
droppings must be washed off immediately
and thoroughly as the acid they contain is
particularly aggressive. Avoid parking the
vehicle under trees (unless it is absolutely
necessary). Remove any resinous plant
matter immediately because, once it has
dried, it may require the use of abrasive
and/or polishing products to be removed,
which are strongly discouraged as they
could potentially alter the characteristics of
the paintwork. Do not use pure windscreen
washer fluid for cleaning the front
windscreen and rear window; dilute it min.
50% with water. Only use pure screen
washer fluid when strictly necessary due to
outside temperature conditions. Do not use
chemicals/acids to defrost windows/vehicle
glass as they can damage the paint.
50)
Avoid washing with rollers and/or
brushes in washing stations. Wash the car
only by hand using neutral pH detergents;
dry it with a wet chamois leather. Abrasive
products and/or polishes should not be used
for cleaning the car. Bird droppings must be
washed off immediately and thoroughly
as the acid they contain is particularly
aggressive. Avoid (if at all possible) parking
the car under trees; remove vegetable
resins immediately as, when dried, it may
only be possible to remove them with
abrasive products and/or polishes, which is
highly inadvisable as they could alter the
typical opacity of the paint. Do not use pure
windscreen washer fluid for cleaning the
front windscreen and rear window; dilute it
min. 50% with water. Only use pure screen
washer fluid when strictly necessary due to
outside temperature conditions. Do not use
chemicals/acids to defrost windows/vehicle
glass as they can damage the paint.
51)
A high pressure jet cleaner should
not be used for cleaning the engine
compartment. The appropriate precautions
have been taken to protect all parts and
connections, but the pressures generated by
these devices are so high that complete
protection against water seepages cannot
be guaranteed.
IMPORTANT
7)
Detergents pollute the water. The vehicle
should be washed in areas equipped for
collecting and purifying the liquid used in the
washing process.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст