Citroen Berlingo Dag (2011 year). Instruction — part 5
6
7
a
n
d
C
O
MF
O
R
T
3
Seats
REAR BENCH SEAT
Each 1/3 - 2/3 section can be folded
fully, then removed individually.
Head restraint
High position: lift and raise the head
restraint.
Low position: press on the head
restraint to lower it.
To remove the head restraint, after
raising it press the tab and lift the head
restraint.
To install the head restraint, engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
The 1/3 - 2/3 rear bench seat is fi tted
with "comma" head restraints.
68
Seats
Fully folded position
Example of operations for the
1/3 section. They are identical for the
2/3 section.
- Place the head restraints in the low
position.
- If necessary, move the front seats
forward.
- Press the grey control located on
the upper part of the seat back.
- Fold the seat back onto the seat
cushion.
- Raise the grey control bar, located
at the rear of the seat cushion.
- Tilt the entire seat forward.
Putting back in place
Tilt the entire seat rearwards until it
locks.
Raise the seat back.
The seat is locked correctly when the
control (at the top of the seat back) is
no longer visible.
Check that the seat is locked
on the fl oor securely when it is
returned to the sitting position.
6
9
EA
SE
O
F
U
SE
a
n
d
C
O
MF
O
R
T
3
Seats
Removing the bench seat
- If necessary, move the front seats
forward.
- Place the bench seat (1/3 section
and/or 2/3 section) in the fully
folded position.
Refitting the bench seat
- Offer up the bench seat (1/3 section
and/or 2/3 section) vertically.
- Place the hooks between the
two bars.
- Fold the bench seat rearwards.
Refer to the "fully folded position"
described on the previous page.
To return the bench seat
(1/3 section and/or 2/3
section) to the "passenger
transportation" position, refer to the
"fully folded position" described on the
previous page.
- Tilt the entire seat rearwards by
approximately 45°.
- Lift the bench seat vertically to the
limit of the anchorages.
- Straighten bench seat by tilting it
forwards then lift it.
70
Seats
Head restraint
High position: lift and raise the head
restraint.
Low position: press on the head
restraint to lower it.
To remove the head restraint, after
raising it press the tab and lift the head
restraint.
To install the head restraint, engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
Each seat can be removed individually.
Each time a seat is returned to the
sitting position or after removing then
refi tting a seat, check that it is locked
on the fl oor securely.
The three independent rear seats are
fi tted with "comma" head restraints.
The back of the centre seat, folded onto
the seat cushion, has a shell which
serves as a table with cup holder.
7
1
EA
SE
O
F
U
SE
a
n
d
C
O
MF
O
R
T
3
Seats
Adjusting the angle of the seat back
- Operate the control and adjust the
angle of the seat back.
Placing the seat back in the
table position
- Pull the control to fold the seat back
onto the seat cushion.
Do not place hard or heavy objects
on the table. They could become
dangerous projectiles in the event of
sharp braking or impact.
Returning the seat back to the
sitting position
- Release the seat back by pulling
the control, then return it to its
original position.
When returning the seat back to the sitting
position, ensure that it is locked securely.
Placing the seat in the fully
folded position
- Pull the control to place the seat
back in the table position.
- Raise the bar located behind the seat
to release the rear anchoring points.
- Tilt the entire seat forwards, until it
locks.
Returning the seat to its original position
-
Push the red control.
- Fold back the seat to fi x the rear
anchoring points.
-
Raise the seat back by pulling the control.
Check that the entire seat is anchored
securely.
72
Seats
Removing the seat
- If necessary, move the front
seats forward and lower the head
restraint.
- Place the seat in the fully folded
position.
Good practice
Following the various operations:
- do not remove a head restraint
without storing it and fi x it to a
support,
- ensure that the passengers can
always access the seat belts and
fasten them easily,
- a passenger must never take
his seat without adjusting and
fastening his seat belt.
Refer to the "fully folded position"
described on the previous page.
- Press the red lever to release the
front feet.
- Tilt the entire seat rearwards by
approximately 45° without releasing
the lever.
- Release the lever.
- Lift the seat vertically to the limit of
the anchorages.
- Straighten the seat by tilting it
forwards then lift it.
Putting the seat back in place
- Tilt the seat forward by 45°.
- Place the hooks between the two
bars.
- Fold back the seat to fi x the rear
anchoring points.
- Pull the control to return the seat
back to its initial position.
- Raise the head restraint.
Check that no object is obstructing
the anchoring recesses or preventing
correct locking of the seats.
7
3
a
n
d
C
O
MF
O
R
T
3
Seats
Head restraint
This is of the "comma" type.
High position: press the tab, lift and
raise the head restraint.
Low position: push the tab and press
the top of the head restraint to lower it.
To remove the head restraint: place it in
the high position, lift it, then remove it.
Store it inside the vehicle, securing it
fi rmly.
To install the head restraint: engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
Each seat can be removed and must
be replaced in the specifi ed position,
indicated by a symbol on its label.
The seats of row 2 and row 3 are
independent and adjustable.
REAR SEATS (7 SEAT VERSION)
74
Seats
Left-hand side seat
Types of Row 2 seat
Types of Row 3 seat
Centre seat
Right-hand side seat
Right-hand side seat
Left-hand side seat
7
5
EA
SE
O
F
U
SE
a
n
d
C
O
MF
O
R
T
3
Seats
Adjusting the angle of the seat back
- Operate the control and adjust
the angle.
Placing the seat in the table position
- Lower the head restraint fully.
- Operate the control to fold the seat
back onto the seat cushion.
Returning the seat back to the
sitting position
- Release the seat back by pulling
the control, then return it to its
original position.
Ensure that the entire seat is anchored
securely.
Placing the seat in the fully folded
position
- Place the seat in the table position.
- Pull the red strap, located behind
the seat, to release the feet of
the seat from their anchorage on
the fl oor.
- Tilt the entire seat forwards.
Row 2 seat adjustments
Returning the seat to its original
position
- Fold back the entire seat.
Before folding the seat, ensure
that:
- in row 3, no passenger's foot is
at one of the seat anchorages
on the fl oor,
- the seat is locked securely on
the fl oor,
- the seat belt is available for
the passenger.
76
Seats
Row 3 seat adjustments
Placing the seat back in the table
position
- Lower the head restraint fully.
- Operate the control to fold the seat
back onto the seat cushion.
Returning the seat back to the
sitting position
- Release the seat back by pulling
the control, then return it to its
original position.
Ensure that the entire seat is anchored
securely.
Returning the seat to its original
position
-
Push the red control.
- Fold back the entire seat.
Placing the seat in the fully folded
position
- Place the seat in the table position.
- Raise the bar fi tted with a red
strap, located behind the seat, to
release feet of the seat from their
anchorage on the fl oor.
- Tilt the entire seat forwards.
Ensure that:
- the seat is locked securely on
the fl oor,
- the seat belt is available for
the passenger.
7
7
EA
SE
O
F
U
SE
a
n
d
C
O
MF
O
R
T
3
Seats
Entering, exiting from row 3
Entering
- Place the row 2 seat in the table
position.
Exiting
- Lower the head restraint fully.
- Operate the yellow control, located
on the back of the row 2 seat back.
- Fold the seat back to the table
position.
Ensure that the stored centre
seat belt is placed correctly in its
strengthener in the headlining.
-
Tilt it to the fully folded position to
allow access.
- Pull the red strap to place the seat
in the fully folded position.
- Tilt the entire seat forwards.
- Exit via the side door.
Before folding it back, ensure that
the feet of the passenger in row 3
are not obstructing the row 2 seat
anchoring points.
78
Seats
Removing the seat
- If necessary, move the front seats
forward.
- Lower the head restraint.
- Place the seat in the fully folded
position.
- Tilt the entire seat forwards then
lift it.
Repositioning the seat
The label on the seat indicates the
position in which it must be installed.
- Place the hooks of the front feet
between the two bars.
- Fold back the seat to fi x the rear
anchoring points.
- Operate the control to raise the
seat back to its initial position.
- Raise the head restraint.
Ensure that no object or foot of
a passenger seated in the rear
is obstructing the anchoring
recesses or preventing correct locking
of the seat.
Handling the Row 2 seat
7
9
a
n
d
C
O
MF
O
R
T
3
Seats
Handling the Row 3 seat
Removing the seat
- Lower the head restraint.
- Place the seat in the fully folded
position.
- Tilt the entire seat forwards.
- On each side, take hold of the
uprights of the folded seat, tilting it
forward slightly, and lift it.
Repositioning the seat
The label on the seat indicates the
position in which it must be installed.
- Place the hooks of the front feet
between the two bars.
- Ensure that no object or foot is
obstructing the rear anchoring
recesses and that the seat belt is
positioned correctly and available.
- Fold back the seat to fi x its rear
anchoring feet.
- Operate the control to raise the
seat back to its initial position.
- Raise the head restraint.
Good practice
Do not place hard or heavy objects on
the seat backs forming a table, they
could become dangerous projectiles in
the event or sharp braking or impact.
Following the various operations:
- do not remove a head restraint
without storing it, fi x it to a support
in the vehicle,
- ensure that the passengers can
always access the seat belts and
fasten them easily,
- a passenger must never take
his seat without adjusting and
fastening his seat belt.
- a passenger seated in row 3 must
ensure that he does not obstruct
the row 2 seat anchoring recesses.
8
0
Seats
ADJUSTMENTS AND DIFFERENT CONFIGURATIONS OF THE SEATS
5 seat layouts
8
1
EA
SE
O
F
U
SE
a
n
d
C
O
MF
O
R
T
3
Seats
7 seat layouts
The various operations
must be carried out while
stationary.
82
Steering mounted controls
1. Lower glove box
This may or may not be fi tted with a lid.
Upper storage compartment
This is located on the fascia, behind
the steering wheel.
A recess makes lifting of the lid easier
when opening. Guide it to its rest
position.
To close, guide the lid then press the
centre gently.
Any liquid which could spill risks
causing an electrical short circuit and
therefore a potential fi re.
3. Side storage compartment
4. Bag hook
Only hang fl exible bags which are not
too heavy on this hook.
2. Storage tray and bottle holder
(1.5 L)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст