Citroen Jumper Relay (2012 year). Instruction — part 4

47

3

E

ASE OF USE

and

COMFOR

T

Steering mounted controls

LIGHTING CONTROL STALK

Selection is by rotation of the white mark on
the ring.

Direction indicators

(green flashing)

Left: downwards.
Right: upwards.

STEERING MOUNTED CONTROLS

Sidelamps on

Dipped/main beam

headlamps on

Switching between dipped and main

beam

Pull the control stalk fully towards you.

Headlamp flash

Pull the control stalk towards you,
regardless of the position of the ring.

Front foglamps

Rear foglamps

If your vehicle is fitted with foglamps, these
operate with the dipped or main beam
headlamps.
Press one of these controls to switch on the
lamps.

The foglamps should only be used in
fog or when snow is falling.

In clear weather or in rain, both day and
night, rear foglamps dazzle and their use is
prohibited.
Do not forget to switch them off when they
are no longer necessary.

"Motorway" function

Pull the lever towards the steering wheel
with a press, without passing the point
of resistance of the lighting stalk; the
corresponding direction indicators will flash
five times.

48

Steering mounted controls

AUTOMATIC ILLUMINATION OF HEADLAMPS

Activation

Turn the ring to this position.
The lamps are switched off
automatically when the ignition is
switched off.

Do not cover the sunshine sensor at
the top centre of the windscreen.

GUIDE-ME-HOME LIGHTING

Ignition off or key in the STOP position.
Within 2 minutes after switching off the
engine, position the ignition key in the STOP
position or remove it.
Pull the lighting stalk towards the steering
wheel.

The indicator lamp comes on in

the instrument panel.
Each action on the lighting stalk,
pulled towards the steering

wheel, prolongs the guide me home
lighting by 30 seconds up to approximately
3 minutes. When this time has elapsed, the
lamps are switched off automatically.
Deactivate this control by keeping the stalk
pulled towards the steering wheel for more
than 2 seconds.

If your vehicle is fitted with this function:
when you leave your vehicle, the dipped
beam headlamps remain on for the selected
duration (when leaving a car park for
example).

To set the sensitivity of the sensor,
refer to "Mode" in chapter 4 .

If your vehicle is fitted with this function, the
dipped beam headlamps are switched on
automatically if the light is poor.
In fog or snow, the sunshine sensor may
detect sufficient light. Therefore, the lamps
will not be switched on automatically. If
necessary, you must switch on the dipped
beam headlamps manually.
They are switched off when the light returns
to a sufficient level.

49

3

E

ASE OF USE

and

COMFOR

T

Steering mounted controls

HEADLAMP BEAM

You are advised to adjust the height of the
headlamp beams in accordance with the
load in your vehicle.
This function works in the dipped and main
beam headlamps position.

Press these controls, located
on the dashboard, several times
in succession to adjust the
headlamps.
An indicator lamp on the screen
indicates the adjustment position
selected (0, 1, 2, 3).

PARKING LAMPS

This system enables you to leave the lamps
on when parked; with the ignition off, key in
the STOP position or key removed.
Move the ring on the lighting stalk to position
O then to dipped or main beam headlamps.

The warning lamp on the
instrument panel comes on.
The lamps will remain on while
you are parked.

Leaving the lighting on for long periods may
significantly reduce the state of charge of
your vehicle's battery.

Travelling abroad
If using your vehicle in a country

that drives on the other side of the road,
the headlamps must be adjusted to avoid
dazzling on-coming drivers.
Contact a CITROËN dealer or a qualified
workshop.

50

Steering mounted controls

WIPER STALK

Slow continuous wiping: 2 notches downwards.

Do not cover the rain sensor, located at
the top centre of the windscreen.

When washing the vehicle, switch off the
ignition or deactivate the automatic rain
sensitive wipers.

Screenwash and headlamp wash

Pull the stalk towards you, the wash-wipe
is accompanied by a timed operation the
wipers.
The headlamp wash is linked with the
screenwash, it is triggered if the dipped
beam headlamps are on.

Windscreen wipers

Wiping is only active when the ignition key is
in the RUNNING position.
The stalk has five different positions:

Wipers off.

Intermittent wiping:
1 notch downwards.
In this position, four speeds
can be selected by turning the ring:

- very slow intermittent,
- slow intermittent,
- intermittent,
- fast intermittent.

Automatic rain sensitive windscreen

wipers

If your vehicle is fitted with this system, the
wiping speed is adapted automatically to the
intensity of the rainfall.
Automatic wiping: 1 notch downwards. This is
confi rmed by one wipe. Must be reactivated
each time the ignition is switched on.
In this position, the sensitivity of the rain
sensor can be increased by turning the ring.

Good practice

Check that the windscreen wiper blades can
operate freely when using the wipers in icy
weather.
Use the step in the front bumper, to remove
any accumulation of snow at the base of the
windscreen and on the blades.

To change the blades, refer to the
"Changing a wiper blade" section of
chapter 8.

To top up the levels, refer to the
"Levels" section of chapter 7.

Fast continuous wiping: 3 notches
downwards.

Single wipe, pull the control towards the
steering wheel.

With Stop & Start, when the wiper
control stalk is in the fast wipe position,

the STOP mode is not available.

51

3

E

ASE OF USE

and

COMFOR

T

Steering mounted controls

CRUISE CONTROL

"This is the speed at which the driver wishes to
travel".
This aid to driving in free-fl owing traffi c conditions
enables the vehicle to maintain a constant
speed programmed by the driver, except when a
considerable load is carried on a steep gradient.
In order to be programmed or activated,
the vehicle speed must be greater than
approximately 25 mph (40 km/h), with at least
4th gear engaged.

Function selected.

Function deactivated.

If your vehicle is fitted with cruise control,
this is displayed on the instrument panel by
an indicator located in the rev counter.

52

Steering mounted controls

Selecting the function - ON

When the selection is set
to ON , this switches the
function on.
If your vehicle is fi tted with

this screen, a message confi rms the action.

Programming a speed

Accelerate to the required speed, with 4th or
5th gear engaged.
Move the control upwards (+), for
approximately one second, to store this
speed.
Release the pressure on the accelerator
pedal, the vehicle will maintain this speed.

Switching off / deactivating the

function

Press the brake or clutch pedal or place
the dial in the OFF position, the indicator is
switched off.
If the ESP or ASR comes into operation,
the cruise control function is deactivated
temporarily.

-

increase the speed in steps, by means
of brief presses, or continuously by
pressing and holding the control
upwards (+ sign),

Temporarily exceeding the

programmed speed

When the cruise control is active, it is still
possible to exceed the programmed speed
by pressing the accelerator pedal
(to overtake another vehicle for example).

-

decrease the speed continuously
by pressing and holding the control
downwards (- sign).

Restore - RES

To restore the vehicle's
programmed speed (for example
after pressing the brake or clutch

pedal), gradually return to the chosen speed
and press RES .
The indicator comes on, the cruise control
function is restored.

Changing the programmed speed while

the cruise control is in operation

You can:

53

3

E

ASE OF USE

and

COMFOR

T

Steering mounted controls

Good practice

When changing the programmed reference
speed by pressing and holding the control,
take care as the speed may increase or
decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
On a steep gradient, the cruise control will
not be able to prevent the vehicle from
exceeding the programmed speed.
The cruise control cannot, in any
circumstances, replace the need to comply
with speed limits nor can it replace the need
for vigilance and responsibility on the part
of driver.
It is advisable to leave your feet near the
pedals.
To prevent the mat from becoming caught
under the pedals:
-

ensure that the mat is positioned
correctly,

-

never fit one mat on top of another.

Cancelling the programmed

speed

When the vehicle stops, after the ignition is
switched off, the system no longer stores
any speed.

Operating fault

In the event of a malfunction, the function is
switched off and the indicator switches off.
Contact a CITROËN dealer to have the
system checked.

54

Ventilation

VENTILATION
DEMISTING AND DEFROSTING

Manual mode

Direct the control to this air
distribution setting.
For faster and more effective
demisting and defrosting of

the windscreen:

Defrosting the rear screen

and mirrors

Only operates when the engine
is running. Pressing this button
activates the rapid demisting-
defrosting of the rear screen and

door mirrors.
This function switches off automatically to
prevent excessive energy consumption. It
stops when the engine is switched off but
resumes when the engine is started again.
Pressing this button switches the function off.

-

increase the air flow setting,

- move the exterior air intake

control temporarily to air
recirculation.

Returning to the exterior air
intake position permits renewal
of the air in the passenger
compartment.

Windscreen and side windows
The ventilation outlets located at the base
of the windscreen and the side vents for the
side windows increase the effectiveness
of the demisting and defrosting. Do not
obstruct these air outlets.
The pollen filter continuously and effectively
filters dust.
Air recirculation (which can be activated by
the driver or the passenger) isolates the
passenger compartment from the exterior
atmosphere. However, this position should
only be used temporarily, normal use is to
drive with the control positioned with the
exterior air intake open.

With Stop & Start, when the heated
rear screen is switched on, the STOP
mode is not available.

55

3

E

ASE OF USE

and

COMFOR

T

Ventilation

CORRECT USE OF THE AIR CONDITIONING

In order to be effective, the air conditioning
should only be used with the windows
closed. However, if the interior temperature
remains high after a prolonged period
parked in the sun, first ventilate the
passenger compartment for a few minutes.

For even air distribution, ensure that the
exterior air intake grille located at the base
of the windscreen is not obstructed and that
the side and central vents, the air outlets on
the floor and the air extractor at the rear are
open.
The air conditioning is useful in all seasons
as it eliminates condensation and air
humidity.

Operate the air conditioning system for
5 to 10 minutes, once or twice a month,

to keep it in good working order.
Have the filter elements (air filter and
passenger compartment filter) replaced
regularly. If you drive in a dusty environment,
have them replaced twice as often.
It is normal that the condensation created by
the air conditioning system results in a flow
of water which may form a puddle under the
vehicle when parked.
If the system does not produce cold air, do
not use it and contact a CITROËN dealer.

"Leave them open"
For optimum distribution and diffusion of hot
or cool air in the passenger compartment,
there are: 4 adjustable central vents, of
which 2 can be directed sideways (right or
left) towards the top of the body and
4 side vents which can be directed towards
the passengers. The air vents directed
towards the floor of the vehicle complete the
equipment.

VENTS

56

Ventilation

WITH MANUAL ADJUSTMENT

If your vehicle is fitted with these controls,
they are located on the dashboard on the
centre console control panel.

Temperature adjustment

Control positioned:
- in the blue zone provides cool air,

Air flow

The force of the blown air, from
the vents, varies from 1 to the
strongest 4. Remember to adjust
this control in order to reach the

ambient air comfort level. To switch off the
blower, place the control in position 0.

Air conditioning

The air conditioning mode can only operate
with the engine running.

The air blower must be set to at
least 1.
Pressing the button triggers the
operation of the air conditioning,

the LED is on. Pressing the button again
switches the function off and the LED is
switched off.

Air distribution

The air supply distribution is directed by the
control turned towards:

the side vents and the central
vents,

the side vents, the central vents
and the footwells,

the footwells,

the windscreen, the footwells and
the side windows,

the windscreen and the side
windows.

- in the red zone provides heating

of the interior ambient air.

57

3

E

ASE OF USE

and

COMFOR

T

Ventilation

Intake of exterior air

Recommended settings for the air conditioning

For optimum operation of the system, the settings below are recommended:

Recirculation of interior air

This position should only be
temporary.
Used with the air conditioning
switched on and setting of the

force of blown air (from 1 to 4), recirculation
enables you to obtain the required ambient
air comfort level with both hot or cold
settings.
Recirculation temporarily prevents exterior
odours and smoke from entering the
passenger compartment.

If I require...

Air

distribution

Temperature

Air flow

Air

recirculation

AC

Heating

-

Cooling

Demisting

Defrosting

When your ambient air comfort level has
been reached, return to the intake of exterior
air position to permit renewal of the air in the
passenger compartment and demisting. This
operating mode is preferable.

This is the preferred operating position.

58

Ventilation

MONO-ZONE DIGITAL AIR

CONDITIONING

If your vehicle is fitted with this system, the
controls are located in the middle of the
dashboard. The system can be identified by
its control screen.

AUTO mode

Switching on FULL AUTO
mode: pressing the AUTO
control switches on the system's
functions, confi rmed by the display

of FULL AUTO . This is the normal operating
mode for the digital air conditioning system.
Using the moving ring surrounding the AUTO
control, set the comfort temperature to be
reached according to a setting between:
-

HI (High to ≈ 32) and,

-

LO (Low to ≈ 16).

The system controls the distribution,
fl ow and intake of air to ensure comfort
equivalent to the setting displayed and

suffi cient recirculation of air in the passenger
compartment.
No further adjustments are required.

Control screen for your digital air conditioning
system.

When the engine is running and the air
conditioning is on, this symbol and the
message FULL AUTO are displayed.

The other components are displayed
according to the settings selected by the user.

AUTO mode with personalisation

Switch on in AUTO mode, certain
settings can be modified: the
distribution, the air flow, the air
conditioning and the air intake/
recirculation.

The display changes from FULL AUTO to
AUTO .
To return to fully automatic operation, press
this button again. The display on the control
panel changes from AUTO to FULL AUTO .
If the system is not able to maintain
the setting selected following manual
adjustments, the setting flashes then AUTO
is cleared. Press the AUTO control to return
to the automatic settings.

Switching off the air conditioning

Pressing this control switches
off the air conditioning functions.
The snowflake is cleared from the
screen.

Complete switch-off

Pressing this control switches
the system off. The LED and the
screen switch off.

59

3

E

ASE OF USE

and

COMFOR

T

Ventilation

Comfort value adjustment ring

The settings range between:
-

increasing the interior ambient air
temperature HI (High) which goes up to
to a maximum setting of 32,

-

cooling the interior ambient air
temperature LO (Low) which goes down
to a setting of 16.

Air distribution

A press illuminates the LED on the buttons
which distribute the air flow towards:

the windscreen and front side
window vents (demisting/
defrosting the windows),

the central and side vents (chest
and face),

the vents in the front and rear
areas (feet).

The combination of buttons permits
improvement of air distribution.

Air flow

Successive presses of this button
increase (+) or reduce (-) the
force of the air flow to the interior.

Intake of exterior air/

recirculation of interior air

When the LED is on, the air
recirculates inside the passenger

compartment to prevent the entry of exterior
odours and smoke. This position should be
temporary.
When the ambient air comfort level has been
reached, pressing the button switches the
LED off and reopens the exterior air intake.
Pressing the AUTO button also restores
the intake of exterior air. Returning to this
position permits renewal of the air in the
passenger compartment and demisting.
Pressing the AUTO button again restores
the FULL AUTO function.

Rapid demisting/defrosting

Pressing this control permits
rapid clearing of the windows.
The LED is on.

The system manages the air conditioning,
the flow and intake of air, the defrosting
of the rear screen and provides optimum
distribution of the air to the windscreen and
front side windows.
If your vehicle is fitted with additional
heating, switch it off to ensure rapid and
effective demisting/defrosting.

ADDITIONAL REAR VENTILATION

The controls for this system,
additional to the standard cabin
ventilation system, are on the
lower dashboard, to the right of
the steering wheel.

Air outlet
A press on this control activates
the extraction of air to the
outside; the LED comes on.
Press again to switch off.

Air inlet
A press on this control activates
the entry of air into the cabin; the
LED comes on. Press again to
switch off.

Ventilation

ADDITIONAL HEATING SYSTEMS

Supplementary heating

On the 2-3 seats version, this is located
under the seat on the driver's side with air
diffusion directed forwards.

REAR HEATING AND/OR AIR

CONDITIONING

If your vehicle is fitted with an
additional air conditioning unit,
located in the rear of the vehicle:
the distribution duct located in

the roof and the individual diffusion vents
provide a perfect diffusion of cold air.
The warm air diffused at the fl oor, from the
front air conditioning unit, is distributed at the
feet of the rear passengers of rows 2 and 3.
A warm air diffusion vent, located on the rear
left wheelarch, may complete the assembly
for the feet of the rear passengers of row 3.

Additional heating

This is passenger compartment heating,
additional to the standard equipment.
It can operate independently of the engine.

Additional heater or programmable

additional heating

This is an additional, programmable and
separate system which heats the Diesel
engine hot coolant loop to make starting
easier.
It improves the demisting and defrosting
performance and that of the heated seats, if
fitted to the vehicle.
The passenger compartment heating is
brought up to temperature more rapidly.
This system must be programmed to start up
before you enter the vehicle.

On the 5-9 seats version, it is
located at the rear. Depending
on the model version, the air
diffusion is either direct from the

rear or comes from the rail located under
each of the two rows of seats.

Press this control to activate/
deactivate the heating. The LED
is on if the heating is activated.
When rapid demisting and

defrosting is required, switch off the control.

61

3

E

ASE OF USE

and

COMFOR

T

Ventilation

Activation/Deactivation

This control, located on the
control panel at the right-hand
end of the dashboard, enables
you to activate/deactivate the

operation of the rear controls from the
driver's seat.
The first press activates (LED on).
A second press deactivates (LED off).

To deactivate the blower, place the control in
position 0.

However, a safety device will ventilate the
rear circuit automatically, even if the control
is in position 0, to prevent the formation of
condensation.

Air flow

The force of the blown air, via
the vents, varies from 1 to the
strongest 4.
To obtain a comfortable level of

ambient air, remember to adjust this control.

Comfort value adjustment

-

on the blue, produces cool
air,

-

on the red, produces
heating of the ambient air.

The OFF control on the "Mono-zone" central
control panel switches the function off.

Control positioned:

62

Ventilation

PROGRAMMABLE ADDITIONAL

HEATING

If your vehicle is fitted with separate
programmable heating: it gradually brings
the engine up to a good temperature to
facilitate starting.

An integrated clock permits programming of
its start time. The passenger compartment
will be heated more quickly.

Heating cycle indicator lamp

Digital programming control

The programmable heating system control
panel is located at the bottom right of the
dashboard.

Display on

Displaying the programme
number selected

Time display button

Time setting buttons

Selection of the stored
programme

Button for immediate switching
on of the heating

Time setting and reading
indicator lamp