Citroen C8 (2013 year). Instruction — part 5
EASE OF USE and COMFORT
3
63
Seats
Memorising seat positions
Two driving positions can be
memorised, using buttons M/1 and
M/2 .
These are located on the side of the
seat:
-
Place the ignition key in the
"running" position (2nd notch),
-
Adjust your seat,
-
Press button M , then button 1
for a fi rst driving position within
four seconds.
Repeat the same actions on buttons M
and 2 to store another driving position.
An audible signal confi rms that a
position has been memorised.
Memorising a new position cancels the
previous one.
Activating a memorised driving
position
Front heated seat
controls
When the engine is running, the front
seats can be heated separately.
Use the adjustment controls located on
the side of each front seat to switch on
and select the self-regulated level of
heating:
1: Low.
2: Medium.
3: High.
0: Off.
After recalling a memorised
position fi ve times in succession,
the function will be cancelled until
the engine is started.
Engine running
-
Keep button 1 or 2 pressed down
until the end of setting of the
corresponding memorised position.
Engine off
-
Briefl y press button 1 or 2 to recall
the corresponding memorised
position.
64
Seats
Rear bench seat
One three-seat bench seat, row 3.
Rear side seats
Two rear passenger seats, left and right side position,
rows 2 and 3.
Rear centre seat
One rear passenger seat, row 2 central position and row 3
left side position. Integrated seat belt. Plastic shell trim.
Folds to the low table position.
EASE OF USE and COMFORT
3
65
Seats
REAR SIDE SEATS
Forwards/backwards adjustment
Lift bar A and slide the seat forwards
or backwards.
Handling the side seat
Adjusting the angle of the seat back
Push lever B upwards and adjust the
angle as required.
Release the lever to lock.
Access to row 3
1. Place the head restraint in the low
position.
2. Push lever B upwards as far as
possible.
Exit from row 3
1. Place the head restraint in the low
position.
2. Pull control C .
3. Guide the tilting of the seat back
forwards until the rear anchorages
are unlocked. If you experience any
diffi culty, use the red emergency
control to unlock the anchorages.
4. Place the seat in the vertical closed
position.
Following each entry or exit,
reposition the raised seat guiding
it until the rear anchorages lock in
their rails.
3. Fold the seat back onto the seat
cushion and guide the tilting of the
seat back forwards until the rear
anchorages are unlocked. If you
experience any diffi culty, use the
emergency control to unlock the
anchorages.
4. Place the seat in the vertical closed
position.
66
Seats
Control for sliding the rear side
seats from row 3 or the boot
Pull the strap (marked with the arrow
symbol) to slide the seat in front of you.
Removing the side seat
1. Tilt the seat back forwards to
detach the rear anchorages.
2. Grab the red strap which appears
and pull it upwards, the front
anchorages unlock .
3. The strap, like the handle, enables
you to remove the seat.
Refi tting the side seat
Check that there is no obstacle
obstructing the slides or
preventing correct locking of the
seat anchorages.
1. Place the front anchorages at the
front stop in the slides. Support the
strap fi rmly for easier positioning of
the seat.
2. Tilt the folded seat towards the rear.
The rear anchorages lock.
3. Raise the seat back.
4. Slide the seat .
EASE OF USE and COMFORT
3
67
Seats
ROW 2 CENTRE SEAT
This can be placed in row 3, on the left.
"Low table" position
1. Place the head restraint in the low
position.
2. At the top (at the back of the seat),
lift the handle identifi ed by the
symbol and guide the tilting of the
seat back towards its seat cushion.
3. You have a "low table". To return to
the seat position, lift the handle and
guide the raising of the seat back.
Removing the centre seat
1. Place the seat in the "low table"
position.
2. Using the control which you pull, tilt
the seat back forwards so releasing
the rear anchorages from the
slides.
3. Grab the red strap which appears
and pull it upwards, the front
anchorages unlock .
4. The strap, like the handle, enables
you to remove the seat.
68
Seats
Rear head restraints
The rear head restraints can be
removed and have two positions:
-
high, position for use,
-
low, storage position.
To raise or lower a head restraint, pull
it forwards sliding it at the same time.
To remove it, place it in the high
position, push the lug and pull it
forwards and upwards.
To refi t it, engage the head restraint
rods in the holes taking care to remain
in the centreline of the seat back.
Never drive with the head
restraints removed, they must be
in place and correctly adjusted.
Refi tting the centre seat
1. Place the front anchorages at the
front stop in the slides. Support the
strap fi rmly for easier positioning of
the seat.
2. Tilt the folded seat towards the rear.
The rear anchorages lock.
3. Raise the seat back and slide the
seat.
Turning a rear seat round
The rear seats can be placed in a "face
to face" position.
Carry out the operations described for
removal then turn the seat round and
resume with the procedure for refi tting
the seat .
This turning operation must be
carried out when stationary.
Driving with a passenger seated
facing the rear is prohibited.
When the vehicle is being driven,
placing a row 2 seat in the closed
position while a passenger is sitting
in row 3 is prohibited.
Check that there is no obstacle
obstructing the slides or
preventing correct locking of the
seat anchorages.
EASE OF USE and COMFORT
3
69
Seats
REAR BENCH SEAT
From the boot, you can pull
on strap B and slide the seat
forwards to make it easier to load
the vehicle.
The rear bench seat must only be
fi tted in row 3.
Seat back folded position
1. Place the head restraints in the low
position.
2. Pull the strap C upwards, from the
tailgate.
3. Tilt the seat back on the seat
cushion.
Vertical position of the bench seat
1. Place the head restraints in the low
position.
2. Pull the strap C upwards, from the
tailgate.
3. Fold the seat back onto the seat
cushion.
4. Pull the lever D to unlock the rear
anchorages.
5. Place the seat in the vertical
"folded" position.
When driving, attach the retaining
straps to the handles.
Forwards/backwards
adjustment
From the seat cushion, lift bar A and
slide the seat towards the front or the
rear.
70
Seats
Removing the bench seat
1. Fold the seat to the vertical
position.
2. Grasp the two bars E underneath
the seat.
3. The front anchorages unlock.
Refi tting the bench seat
For removal and refi tting, pass the
rear seat, in the "folded" position,
through the sliding side doors.
Check that there is nothing
blocking the runners which could
prevent correct locking of the
bench seat anchorages.
1. Position the front anchorages at the
front stop of the runners.
2. Tilt the folded seat rearwards.
3. The rear anchorages then lock.
4. Unlock the seat back and lift it
using the strap C .
Good practice
When the vehicle is being driven, it is
prohibited for a passenger to sit:
-
in row 3 if the seat back in front
(row 2) is in the table position.
-
in row 3 if the seat/bench in front
(row 2) is in the vertical folded
position.
-
in the centre seat if the right-hand
side seat is in the vertical folded
position.
EASE OF USE and COMFORT
3
71
Seats
The centre seat may be installed
in the central position in row 2 and
in the left side position in row 3.
MODULARITY AND POSSIBLE SEAT CONFIGURATIONS
Examples of various
arrangements combining
pleasure and practicality:
The various operations modifying
the existing confi guration must
be carried out with the engine
switched off (See section on "Seats").
It is prohibited to be in a rearwards
facing position when the vehicle is
being driven.
The rotating of the seats depends on
the vehicle equipment and the country.
5 seats with picnic position when
parked
5 seat arrangements
72
Seats
7 seats with access to row 3
8 seats with bench seat
EASE OF USE and COMFORT
3
73
Seats
"Cargo"/Transportation of long objects confi guration
EASE OF USE and COMFORT
3
75
Practical information
FRONT SEAT LAYOUT
Storage drawers
There is a storage drawer under each
front seat.
-
To open it, lift and pull.
-
To take it out, open it to its full
extent, lift the two tabs on either
side of the drawer, then remove it
completely.
PRACTICAL INFORMATION
"Aircraft" type table
You have an "aircraft" type table with a
rim, equipped with a cup holder, fi tted
to the rear of each front seat.
Do not forget to fold this before pivoting
the seat.
12 V socket
You have a 12 V accessory socket
(120 W) at the foot of the driver's seat,
which is accessible to passengers of
row 2.
Front and rear armrests
To place the armrest in its rest
position:
-
Lift the armrest until it is aligned
with the seat back.
Each front seat also has a storage
pocket on the seat back.
To place the armrest in the position
in which it is used:
-
Push it towards the rear,
-
Fold it down completely,
-
Raise it slowly to the required
position,
-
If you lift it past the required
position, restart the above
operations.
76
Practical information
EASE OF USE and COMFORT
3
77
Practical information
1. Driver's upper glove box
FRONT INTERIOR LAYOUT
This is fi tted with a lock.
To open the glove box, lift the handle.
The light comes on when the cover is
opened.
It contains three sockets for the
connection of video equipment and
access to the fascia fuse box.
It includes special compartments for
storing maps, a packet of cigarettes,
an A4 document etc.
RCA sockets.
This permits the connection of a mobile
telephone charger, a baby's bottle
warmer, etc.
To open, press the button.
To close, press the cover.
It includes special compartments for
storing a pen, a mobile telephone,
coins or tokens and credit cards.
2. Audio equipment concealing fl ap
Lower the fl ap fully to lock it in place.
Press the fl ap to raise it.
3. Central storage compartment
4. Passenger's upper glove box
To open, press the button.
To close, press the cover.
It includes special compartments for
storing a pair of spectacles, keys, fi ve
CDs and four audio cassettes or nine
audio CDs.
5. Passenger's lower glove box
6. Lighter or 12 V socket for
accessories (120 W)
12. Mat fi tting/removal
When removing the front mat, push
the seats as far back as possible and
remove the fi xings.
When refi tting, position the mat
correctly on the pins and clip the
fi xings. Check that the mat is secured
correctly.
To prevent the mat from becoming
caught under the pedals:
-
only use mats suited to the fi xings
already present in the vehicle. It
is imperative that these fi xings are
used.
- never
fi t one mat on top of another.
7. Cooled compartment
It can hold up to three cans.
Slide the closer, located on the right, to
open (upwards) or close (downwards)
the air inlet.
8. Can holder and ashtray
This retractable and lit support contains
up to two can holders, a removable
ashtray and a location for the lighter
when it is used as a 12 V socket
(120 W).
9. Storage compartment or
additional telematics control
The storage compartment must not be
used as an ashtray.
If fi tted on your vehicle, the additional
telematics control is located on the
centre console.
10. Storage compartment
11. Door tray with space for a bottle
of water
Bluetooth functions.
78
Practical information
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст