Dacia Solenza (engine E7J). Manual — part 90
THE MECHANICAL ELEMENTS CONTROLS
37
37 - 10
Handbrake secondary cables
SECONDARY CABLE - REPLACEMENT
DISMOUNTING
Disconnect the battery.
Loosen the rear wheels attachment screws.
Release the hand brake control lever (re-
lease position).
Lift the vehicle by means of a two-column
elevator.
Detach the rudder bar fork from the end
rod by unscrewing the lock nut (M12 x 1.25)
and remove the ball-ended washer.
Remove the secondary cables ends from
rudder bar seats.
Dismount the two rear wheels.
Dismount the brake drums ( see chapter 33
– Rear axles elements).
Remove the secondary cables stops from
the central floor.
Dismount the sheathe stops from the brake
plates.
Remove the secondary cables.
REMOUNTING
Grease the cable with UM 185 Li 2M
grease
Perform the dismounting operations in the
reverse order.
Adjust the drum clearance ( see chapter 33-
Rear axles elements”).
Adjust the handbrake control lever stroke.
SPECIAL TOOLS
Ro 441
Wheel drum cover tongs
Fr.600
Hub extractor
TIGHTENING
MOMENTS
(daNm)
Wheel attachment screw
7.5
Steering knuckle nut
16.5
THE MECHANICAL ELEMENTS CONTROLS
37
37 - 11
Brake flexible hoses
IMPOSED
PRECAUTIONS
TO BE RESPECTED
WHEN
DISMOUNTIN
G – REMOUNTING A RECEIVER
OR A BRAKE FLEXIBLE HOSE
Due to security reasons, in order to avoid brake flexible hose twisting and the risk to get in
contact with the suspension elements, it is necessary to observe the following operations sequence,
as well as the flexible attachment on the wing lining by means of a stopper, positioned at 135 ± 2
mm, value to be measured from the connection screw of the rigid pipe with the flexible hose.
DISMOUNTING
Dismount the connection (1) of the rigid pipe (6) from the flexible hose (2) till the moment
when the spring (3) is relaxed, having releasing the splinted area (4) of the sustaining support (5).
TIGHTENING MOMENTS (daNm)
X (flexible on caliper)
2.0
Y (attachment screw of the rigid pipe on the flexible
1.5
135 ± 2
1
THE MECHANICAL ELEMENTS CONTROLS
37
37 - 12
Brake flexible hoses
Unscrew the flexible from the caliper and after that from the connection with the rigid pipe.
REMOUNTING
Assemble the caliper with the caliper fork.
Mount the caliper wedges and then tighten to the required moment the flexible on the caliper.
The flexible hoses must be tighten to the required moment with the rigid pipes, when the front
axle is in the position :
- symmetric wheels (mounted suspension);
- front axle in straight line.
REMARK :
Position the hexagonal area (4) of the flexible in the sustaining support (5) so that
it is not mounted twisted.
Mount the spring (3) and the connection of the rigid pipe on the flexible hose,
observing the required tightening moment.
Purge the brake circuit.
THE MECHANICAL ELEMENTS CONTROLS
37
37 - 13
Brake pressure controller
REMARK :
Brake pressure controller is not to be repaired.
DISMOUNTING
Drain of fluid, the braking circuit.
Lift the vehicle by means of a two-column elevator.
Dismount the connection screws (1) of the rigid piping on the pressure controller.
Dismount the attachment nuts (2) of the pressure controller support on the carriage body.
Remove the support together with the pressure controller from the carriage body.
Dismount the pressure controller off the support.
REMOUNTING
Remount:
- pressure controller attachment screws on the support;
- attachment nuts of the pressure controller assembly on the carriage body;
- connection screws of the rigid piping on the pressure controller, observing the required
tightening moments.
Purge the braking circuit.
Adjust the pressure controller.
TIGHTENING MOMENTS (daNm)
Attachment nut of the pressure controller assembly on the carriage body
1
Connection screws of the rigid pipe on the pressure controller
1.5
2
1
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст