Dacia Solenza (engine E7J). Manual — part 44
IGNITION AND INJECTION
17
17 - 82
AC212
WATER TEMPERATURE WARNING INDICATOR
RECOMMENDATIONS No failure must be present or memorized.
Check the mass presence on the indicator line, after control activating.
Mend if necessary
If a short-circuit has occurred at the supply circuit +12 volts on the indicator line, the instrument
panel may be damaged.
If the incident is persisting, consult the instrument panel diagnostic
Diagnostic – Parameters interpretation
AFTER
Restart the conformity checking from the beginning.
REPARATION
IGNITION AND INJECTION
17
17 - 83
RECOMMENDATIONS
Do not use these information but before performing the complete
checking by means of the CLIP tester
IMPOSSIBI
LITY OF COMMUNICA
TION UCE INJECTION
- CLIP TESTER
ALP 1
STARTING PROBLEMS
(engine is not starting or is difficulty starting)
ALP 2
IDLING PROBLEMS
(unstable idling)
ALP 3
INTEMPERATE ACCELERATION OR DECELERA
TION
(engine unstable running)
ALP 4
ENGINE
OPERATION BREAKDOW
N
ALP 5
ENGINE
STOPPING
ALP 6
ENGINE NOISE
ALP 7
SMOKE
ALP 8
PERFORMANCES LIST
ALP 9
FUEL CONSUMPTION
ALP 10
Failure locating algorithm
IGNITION AND INJECTION
17
17 - 84
ALP 1
IMPOSSIBILITY OF COMMUNICA
TION UCE
INJECTION
CLIP TESTER
RECOMMENDATIONS
Nothing to be noticed
Ensure that not the CLIP tester is the cause of the failure, by trying to communicate with the
computer of another vehicle.
Check connection between CLIP tester and the vehicle diagnostic socket (cable condition).
Check the condition of the injection fuses, engine and cockpit.
Mend if necessary.
Check the presence of the supply +12 V at pin 16 and of the mass at pins 4 and 5 of the diagnostic
device socket.
Mend if necessary.
Connect the 90 ways terminal box instead of the computer and check the insulation, continuity
and absence of the parasite resistance of the connections between:
pin 28 injection computer > mass
pin 33 injection computer > mas
s
pin 3 injection computer >
mass
pin 56 injection computer > p
in 7 diagnostic socket
pin 26 injection computer > p
in 15 diagnostic socket
pin 29 injection computer > fuse
pin 30 injection computer >
fuse
Mend if necessary.
Failure locating algorithm
AFTER
Perform a checking by means of the CLIP tester.
REPARATION
IGNITION AND INJECTION
17
17 - 85
ALP 2
STARTING PROBLEMS engine is not starting or is difficulty starting)
RECOMMENDATIONS
Do not consult this diagnostic but before performing a complete
checking by means of the CLIP tester.
Check that starter is well operating
Check there is petrol in the fuel tank (fuel indicator failure).
Ensure that vehicle is supplied with adequate fuel.
Check that supply circuit hoses are not broken (especially further to a dismounting)
Check the condition of the fuel filter
Check the condition of the fuel tank
Check that fuel tank aeration is taking place.
Check the electric supply of the fuel pump.
Check the good operation of the choke sensor.
Check the motor of the idling regulator.
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Clamp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Check the spark plugs and ignition coil condition
Check that these elements are specific to that vehicle.
Check that the exhaust route is not clogged and the catalyst is not clogged.
Check the engine compressions
Check the flywheel condition
Check the distribution setting on.
AFTER
Perform a checking by means of the CLIP tester.
REPARATION
Failure locating algorithm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст