Dacia Solenza (engine E7J). Manual — part 83
35
WHEELS AND TIRES
35 - 3
Characteristics
Some speed symbols:
Max speed
Kmh
R
S
T
U
H
V
ZR more than
Kmh
170
180
190
200
210
240
240
Structure types :
Radial :R
WHEELS -TIRES
Vehicle type
Wheel
Wheel
Wheel screws
Tires
Inflating pressure
axial/radial
tightening
at cold (bars)
runout
moment
Front
Rear
(mm)
(daNm)
Unloaded/
Unloaded/
Loaded
Loaded
SOLENZA
5.5J14*
0.2/0.8
7.5
165/65R14
2.0/2.2
2.0/2.1
5.5B13
0.2/0.8
7.5
165/70R13
2.0/2.2
2.0/2.1
* aluminum rim
The temperature raising during driving, leads to a pressure increase from 0.2 to 0.3
bars, compared to the prescribed values
In case temperature checking is performed immediately after vehicle driving, take into
account this pressure increase.
WHEELS AND TIRES
35
35 - 4
Wheels balancing
BALANCING WEIGHTS
Use exclusively the weights delivered as spare parts, with attachment by means of mass
incorporated clamps.
A = balancing weights for steel rims
B = balancing weights for aluminum alloy rims.
A
B
36
STEERING ASSEMBLY
36 - 1
Steering connecting rods
SPECIAL TOOLS
DIR. 1306 Device for steering rack locking up
in regard to steering box casing.
P.F. 476
Device for ball joints depressing
DIR. 505
Wrench for dismounting/remounting
joint body on rack
Wheels screws 7.5
Steering ball joint nut 4
Joint body in rack 5
TIGHTENING MOMENTS (daNm)
Disconnect the battery.
Lift the vehicle by means of a two-column elevator.
DISMOUNTING
Depress the rod funnel ball joint from the steering knuckle arm by means of the PF 476
device.
Dismount the bellows maintaining clip from the steering box casing.
Turn the wheels hard over to the right, so that rack is moving towards left.
On the left side
Using the DIR 1306 device , lock up the rack in regard to the steering box casing.
In this position, dismount the joint body from the rack.
Remove the left steering rod.
On the right side, proceed in the same way.
36
STEERING ASSEMBLY
36 - 2
Steering connecting rods
REMOUNTING
At each dismounting, it is OBLIGATORY the replacement of the limiter washer(1) as well
as of the safety washer (2).
Mount in the rack : joint body (3), not before positioning the safety washer (2), the limiter
washer (1) and oiling the threaded part (4) of the joint body with FIXAMED R 58-C.S.1/82
(not excessively).
After tightening to the required moment of the axial ball joint on the rack, bend the safety
washer over one of the cuts made on the joint body.
By means of the DIR 1306, lock up the rack in regard to the steering box casing.
Tighten to the required moment of 5 daNm, the joint body in the rack by means of the
DIR 505 wrench.
Mount the funnel ball joint in the steering knuckle arm, then tighten the nut to the required
moment of 4 daNm.
Position the steering at the middle point ( wheels being in straight line position) in order to
balance the air from bellows.
Mount the bellows in its channel from the steering box casing and secure it using a clip.
CHECKING
Slightly tighten by hand one of the bellows in order to check the other one inflation, in this
way, the good air circulation inside the steering box is checked.
Check the steering geometry and adjust the parallelism if necessary.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст