Dacia Solenza (engine E7J). Manual — part 124
62
AIR CONDITIONING
62- 22
DISMOUNTING (D.S.A.F
. being already dismounted)
The access to the recycling flap gear motor is it possible only after dismounting the air blowing
device (D.S.A.F.)
Disconnect the connector (4)
Dismount the gear motor attachment screw (7).
If necessary, supply the gear motor with 12 V cc so that recycling flap is enabling the dis-
mounting of the gear motor attachment screw (8).
Dismount the gear motor attachment screw.
Extract from its place, carefully, the gear motor
REMOUNTING
Perform the dismounting operations in the reverse order
The new gear motors are delivered in the recycling flap partially-open position are no special
cautions are needed.
Recycling flap motor fan
62
AIR CONDITIONING
62 - 23
Replace fuses F03,
F04, F17 or F26.
Check fuses F03, F04, F17 and F26 from
cockpit.. Are they ok?
Replace front wiring.
Is any n12 V voltage between:
- vehicle’s mass
pin 10 climate control panel ?
- vehicle’s mass
pin 11 climate control panel ?
- vehicle’s mass
pin 10 blower connector ?
- vehicle’s mass
pin 11 blower connector ?
- vehicle’s mass
pin A5 climate control panel ?
- vehicle’s mass
pin A4 climate control panel ?
Replace cold air
blowing device.
Disconnect the blower connector. Connect pin 14 and pin 15 to
the vehicle mass. Connect F26 fuse exit, in turn, to:
- pin 3 blower connector (step 1).
- pin 4 blower connector (step 2)
- pin 5 blower connector (step 3)
- pin 12, pin 10 and pin 11 blower connector (step 4)
Blower working and there is 12 V voltage at pin 9 blower
connector?
Check the continuity and resistance against vehicle’s mass between:
- pin B5 climate panel
pin 3 blower connector
- pin B4 climate panel
pin 4 blower connector
- pin B1 climate panel
pin 5 blower connector
- pin A1 climate panel
pin 12 blower connector
- pin 13 climate panel
pin 9 blower connector
- pin 14 climate panel
pin 1 blower connector
- pin 15 climate panel
pin 2 blower connector
- pin 9 climate panel
vehicle mass
- pin 8 climate panel
vehicle mass
- pin 14 blower connector
vehicle mass
- pin 15 blower connector
vehicle mass
Are they corresponding ?
Replace front wiring.
No
No
No
Yes
Yes
Yes
No
No
Replace ventilation-
climate air distributor.
Disconnect the recycling flap motor connector.
Start the recycling flap motor.
Is there 12 V between the pins of the recycling flap motor connector?
Yes
Yes
Diagnose
CLIMATE BLOWER FAN OR RECYCLING FLAP NOT WORKING
62
AIR CONDITIONING
62- 24
Diagnose
CLIMATE CONTROL PANEL LIGHTING NOT WORKING
Replace fuse F14.
Replace front
wiring.
Check in cockpit fuse F14. Is it OK?
Check the continuity and resistance against vehicle mass between:
- cockpit fuse F 14 exit
pin 7 climate panel;
- pin 9 climate panel
vehicle mass.
Are they corresponding ?
Replace the ventilation-climate
air distributor.
No
No
Yes
Yes
64
CARRIAGE BODY SEALING
64 - 1
1 - climate control protector
2 - climate control box gasket
3 - water evacuation hose
4 - bonnet support
5 - obturators
CLIMATE CONTROL PROTECTOR
DISMOUNTING
Dismount the climate control box gasket.
Swing over windscreen the climate control
protector and detach it from clips from the
climate control box.
REMOUNTING
Perform the dismounting operations in the
reverse order.
Take into consideration that climate control
box gasket is sealing both on the border of the
climate control protector and on the central part
of the climate control box.
WATER EVACUATION HOSE
DISMOUNTING
Dismount
- climate control box gasket;
- climate control protector.
Remove the water evacuation hoses from
the climate control box.
REMOUNTING
Perform the dismounting operations in the
reverse order.
3
1
2
5
4
Carriage body sealing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст