Renault Scenic 3 Chassis. Manual — part 7
31A
-
4
FRONT AXLE ASSEMBLIES
Brake calliper
31A
When replacing brake pads or a disc, be sure to re-
place the pads or disc on the opposite side.
REMOVAL
Mount the vehicle on a two post lift.
Fit the pedal press tool to the brake pedal to restrict
the outflow of brake fluid.
Unlock the steering wheel.
Remove the front wheels.
Undo the brake hose from the brake calliper.
Remove:
- the two guide pin bolts (1),
- the brake calliper,
- the brake pads,
Check the condition of the braking components (re-
place faulty parts).
Clean the calliper supports and callipers.
REFITTING
Push the piston back using tool (Fre. 1190-01) until
it is at the end of its bore.
Fit the pads, starting with the inside.
Refit:
- the calliper,
- the guide pin bolt.
Torque tighten:
- the guide pin bolts (3.2 daNm),
- the brake hose (1.7 daNm).
Special tooling required
Fre. 1190-01
Tool for pushing calli-
per pistons back
Equipment required
pedal press
Tightening torques
m
guide pin bolts
3.2 daNm
brake hose
1.7 daNm
bleed screw
0.65 daNm
wheel bolts
13 daNm
Note:
The callipers supplied as replacement parts are
pre-filled.
WARNING
Prepare for brake fluid outflow, to prevent
damage to the mechanical parts and bodywork
around the braking system.
101214
WARNING
- Mount the brake hose and wheel speed sensor
wiring, if they have been unclipped.
- Do not twist the brake hose.
1
31A
-
5
FRONT AXLE ASSEMBLIES
Brake calliper
31A
Refit the wheels.
Torque tighten:
- the bleed screw (0.65 daNm),
- the wheel bolts (13 daNm).
Bleed the brake circuit partially if the compensation
reservoir is not completely emptied during the proce-
dure. Otherwise, carry out a full bleed ( General Ve-
hicle InformationSection).
Check the brake fluid level.
31A
-
6
FRONT AXLE ASSEMBLIES
Brake calliper mount
31A
When replacing brake pads or a disc, it is essential
to change the pads or disc on the opposite side.
REMOVAL
Mount the vehicle on a two post lift.
Remove the front wheels.
Remove the guide pin bolts (1).
Suspend the brake calliper from the suspension
spring.
Remove:
- the brake pads,
- the two calliper support mounting bolts (2),
- the calliper support.
Check the condition of the braking components (re-
place faulty parts).
Clean the calliper supports and callipers.
REFITTING
Push back the piston using tool (Fre. 1190-01) until
it is at the end of its housing.
The calliper support bolts and the guide pin bolts
must be coated with FRENBLOC or similar product
before being fitted.
Refit:
- the calliper support,
- the calliper support mounting bolts.
Torque tighten the calliper support bolts (10.5
daNm).
Fit the pads, starting with the inside.
Refit:
- the calliper,
- the guide pin bolts.
Check the brake fluid level.
Torque tighten the guide pin bolts (3.2 daNm).
Refit the wheels.
Torque tighten the wheel bolts (13 daNm).
Check the brake fluid level.
Special tooling required
Fre. 1190-01
Tool for pushing calli-
per pistons back
Tightening torques
m
calliper suppor t bolts
10.5 daNm
guide pin bolts
3.2 daNm
wheel bolts
13 daNm
101215
2
1
WARNING
- Mount the brake hose and wheel speed sensor
wiring if they have been unclipped.
- Do not twist the brake hose.
IMPORTANT
Depress the brake pedal several times to bring
the pistons, the brake pads and discs into con-
tact.
31A
-
7
FRONT AXLE ASSEMBLIES
Brake discs
31A
REMOVAL
Brake discs are not regrindable. If there is excessive
scoring or wear, they will need to be replaced.
When replacing a brake disc, be sure to replace the
disc on the opposite side.
Be sure to replace the brake pads if the brake discs
are being replaced.
Mount the vehicle on a two post lift.
Unlock the steering wheel.
Remove the front wheels.
Remove both calliper support bolts (1).
Suspend the calliper / calliper support assembly.
Remove
- the calliper support,
- the two disc mounting bolts (2),
- the disc.
REFITTING
Clean the calliper supports and callipers.
Proceed in the reverse order to removal.
Torque tighten:
- the disc mounting bolts (1.5 daNm),
- the calliper support bolts (10.5 daNm).
The calliper support bolts must be coated with
FRENBLOC or similar product before they are fitted.
Refit the wheels.
Torque tighten the wheel bolts (13 daNm).
Tightening torques
m
disc mounting bolts
1.5 daNm
calliper suppor t bolts
10.5 daNm
wheel bolts
13 daNm
101215
1
101212
WARNING
- Mount the hose and wheel speed sensor wiring,
if they were unclipped.
- Do not twist the brake hose.
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст