Dacia SuperNova (engine E7J). Manual — part 114
80
BATTERY - FRONT HEADLIGHTS
80 - 7
HEADLAMPS ADJUSTMENT
MEETING LIGHTS ADJUSTMENT (LOW BEAM)
This is performed by acting upon the V screw
(vertically plane adjustment) or H (horizontally
plane adjustment). By screwing, the lighting beam
is ”lowering” and by unscrewing is “ascending”.
Check if the lighted area is centered on the
vertical axis and if the optical separation at 15°
coincide with the headlamp lighting. An error
of 1 cm is admissible.
A lighting beam displaced towards left has
the aspect shown in (pict.a) and a lighting beam
displaced towards right has the aspect shown
in (pict.b).
ROAD LIGHTS ADJUSTMENT (LONG BEAM)
Check the position to coincide with the
adjustment performed for low beam and with
the lighting beam distributed between the two
vertical lines on the panel.
When checking the long beam, the lighting
center of the ellipse, must be located on the
cross marking the screen center.
If a major deviation compared with the low beam is noticed, it is recommended the bulb
replacement, this one being in most of the cases, responsible for such defect.
pict.a
pict.b
80
BATTERY - FRONT HEADLIGHTS
80 - 8
HEADLAMPS ADJUSTMENT
FOG LAMPS ADJUSTMENT
The fog lamps adjustment is to be performed in the following conditions:
- the vehicle to be placed on a horizontal surface;
- the vehicle has not passengers inside the cockpit or weights in the trunk;
- the tires are pressurized at the manufacturer prescribed pressure.
Further on, proceed as follows:
Bring the vehicle at the working place.
Position the adjustment device (headlamp adjustment device –E) in front of an optical center
of a fog lamp.
Switch on the fog lamps.
Rotate the adjustment screw of the fog lamp (D), so that an adjustment of 2 % is obtained and
the separation between the lighted area and the dark one from the adjustment device is located
under the marked line (G).
This adjustment is performed in the same way as for the meeting lights adjustment.
Bring the adjustment device in front of the optical center of the second fog lamp.
Perform the fog lamp adjustment.
Switch off the fog lamps.
G
E
81
REAR AND INTERIOR LIGHTING
81 - 1
BULBS REPLACEMENT
BULB REPLACEMENT OF THE REAR TURNING, PARKING AND BRAKE
STOP LIGHT
Disconnect the battery.
Push towards interior the two attachment clips (1), then extract the plastic cap(2).
Disconnect the connector (6).
Push upwards the attachment clips (3) of the printed circuit plate (4), swing it and pull out the
plate from the attachment shoulders (5).
For remounting perform the dismounting operations in the reverse order.
FOG LAMP BULB REPLACEMENT
Dismount the attachment screws (1) of the
fog lamp glass and remove the glass;
Remove the burnt bulb and replace it.
REPLACEMENT OF THE LICENSE PLATE LAMP BULB
Dismount the lamp attachment screws.
Replace the burnt bulb.
For remounting, perform the dismounting operations in the reverse order.
REAR AND INTERIOR LIGHTING
81
81 - 2
BULBS
Hugh/low beam lights
Two phases bulb R2-12V-40/45 W
Headlamps
with flange holder P45t41
Parking lights
Bulb 12V-4W with holder BA 9s
Front turning lamp
Bulb 12V-21W(colored) with holder BAU 15s
Fog lamps
Halogen bulb H3, 12V-55W with holder Pk22s
Rear
Parking, stop lights
Bulb 12V-21/5W with holder BAY 15d
lamps
Turning and reverse driving
Bulb 12V-21W with holder BA15s
Rear fog lamps
Bulb 12V-21W with holder BA 15s
Lamps: side signaling, trunk lighting
Bulb 12V-5W with holder W2,1x9,5
License plate, ceiling, document compartment Bulb SOFIT 10 x 35 type AS02; 12V-5W
lamps
with holder Sv 8,5
Lamp STOP-S3 on the ceiling
Bulb 12V-21W type C21W with holder Sv 8,5
Instrument panel
Bulb 12V-1,2W holderW2 x 4,6d
BULBS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст