Dacia Pick-Up 1304/1305/1307. Manual — part 52
MANUAL GEARBOX
21
21 - 14
DISMOUNTING - REMOUNTING
R
EMO UNTING
Check the state of the centering bushing from the crankshaft end.
Grease the grooves of the clutch shaft with grease U M 170 Li Ca Pb 2 M.
Assembly the gearbox to the engine.
ATTENTION
!!!! Do not catch the clutch mechanism.
Mount the clutch shield plate.
Mount the back crossbar.
Connect the electric wire of the back drive connector.
Connect the propeller shaft and tighten at the required moment ( 5 daNm ) the 4
attachment screws M10 (G.B. 50 and G.B. 51).
Connect:
- the speedometer cable;
- the velocity steps control.
Connect the vacuum hoses and the electrical connector of vacuum capsule (G.B. 51 C).
Grease the propeller shaft grooves with grease UM 170 Li Ca Pb 2M (G.B. 365 and 51 C).
Position the transmission in correspondence with the propeller shaft pinion.
Rock the steering knuckle support, connect the transmission to the propeller shaft
pinion and center it by means of the CV 31-B mandrel.
MANUAL GEARBOX
21
21 - 15
Place the new elastic pins.
The pins notches shall be oriented towards the wheel. The ends of the pins shall be
sealed with RHODORSEAL 5661.
Mount (on both sides):
a. the upper suspension joint
b. the steering joint
Mount the front wheels, take the vehicle down from the elevator and tighten the wheels
nuts at the required moment (9 daNm).
Dismount the TF 509 support cross bar.
Mount the clutch cable with its support.
Adjust the clutch stroke (2,5 – 3,5 mm to the end of shifter shaft).
Adjust the velocity steps gearing.(see chapt.” Velocity steps control adjustment “).
Mount the starter and the protection shield.
Connect :
- the starter power cable ;
- the coupling relay supply wire.
Fill up the gearbox with oil SAE 80/90 ; API GL 5. .
Check the velocity steps gearing.
Connect the battery.
DISMOUNTING - REMOUNTING
MANUAL GEARBOX
21
21 - 16
REPAIR
Dismount the gearbox off the vehicle
Dismount the reverse driving lamp contact.
Dismount the clutch casing.
DISMOUNTING OF THE COUPLING MECHANISM 4X4 (G.B. 51 C)
Dismount the attachment pin of the
connection bolt (1) between the vacuum
capsule shaft and the control lever and take
out the bolt.
Dismount the vacuum capsule support
from the gearbox casing.
Take out the safety washer (2) of the
control lever fixing.
Dismount the control lever (3) of the front
transmission.
Dismount the threaded plug (4) for stroke
limiting.
Unscrew the attachment screws (5) of the
deflector and flange on the differential hub.
Take out the deflector and flange.
Unscrew the attachment differential cover
screws (6) on half crankcase.
Take out the differential cover assembly
and its paper gasket.
Dismount the bearing from the differential
hub by means of an extractor
( only if this is used and must be replaced ).
Take out the annular oil ring from the
differential cover by means of a screwdriver.
2
1
2
6
5
3
4
MANUAL GEARBOX
21
21 - 17
Clean the annular oil seal place from
the differential cover.
Take out the cover (7) from the hub
differential.
Dismount the safety ring (8) from the
propeller shaft gear.
Take out slotted shim (9).
Extract the hub-gear assembly (10)
together with fork and shaft (11).
Take out the claw (12) and the pins
housing (13).
REPAIR
DISMOUNT THE VELOCITY STEP V
Dismount the flange attachment nut
flange on secondary shaft and take out the
flange (G.B. 50C , 51 C).
Bring the gearbox to the dead point and
dismount the back cap.
Engage the velocity step V and the
reverse one.
Unscrew the primary shaft nut.
Bring the gearbox to the dead point,
then engage velocity step IV.
Take out the speedometer spring by
means of CV 204 wrench at GB 365.
12
13
10
9
8 7
11
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст