Dacia Pick-Up 1304/1305/1307. Manual — part 76
FRONT BEARING ELEMENTS
31 - 28
31
FRONT SHOCK ABSORBER
FRONT SHOCK ABSORBER
REPLACEMENT BY MEANS OF THE SUS 478 - 01 DEVICE
The front shock absorber may be dismounted as follows:
- single, using the SUS 478 – 01 device;
- together with the spring, using the SUS 478 device.
D
ISMO UNTING
Mount the PF 509 support crossbar between
the shock absorber lower attachment shaft and
the suspension lower arm shaft.
Lift the engine by means of a 2 columns
elevator.
Remove the plastic shutter mounted on the
shock absorber column.
Dismount the wheel.
Mount the SUS 478 – 01 device on the wing
double lining reinforcemen
t.
Place the threaded rod and compress the
spring.
Loosen the stabilizer rod shaft nut.
Unscrew:
- the shock absorber upper lock nut and nut;
- the shock absorber lower lock nut.
Rotate the shock absorber and remove it from the lower joint.
Push the rod, tilt the shock absorber and take it out.
31
FRONT BEARING ELEMENTS
31 - 29
R
EMOUNTING
Grease the threaded parts of the shock absorber with special MoS2 grease.
Press the rod , tilt and place the shock absorber.
Fully screw the shock absorber into the lower joint.
Pull the shock absorber rod by means of the SUS 513 device.
Position the rubber buffers and the crossbar.
Tighten the upper nut at the required moment.
Tighten the lock nut.
Tighten at the required couple:
- the lower lock nut;
- the stabilizer rod shaft nut.
Dismount the SUS 478 – 01 device.
Mount the wheel.
Lower the vehicle from the elevator.
Remove the PF 509 support crossbar.
FRONT SHOCK ABSORBER
FRONT BEARING ELEMENTS
31 - 30
31
FRONT SHOCK ABSORBER REPLACEMENT BY MEANS
OF THE SUS 478 DEVICE
D
ISMO UNTING
Mount the PF 509 support crossbar.
FRONT SHOCK ABSORBER
Lift the vehicle by means of a 2 columns el-
evator.
Dismount the wheel.
Take the SUS 478 device and perform the
following operations:
- grease the thread of the grippers;
- hook the grippers to the last but one up-
per coil of the shock absorber spring;
- place the lower plate of the device;
- slightly tighten the nuts;
- mount the lock collar at the middle of
the springs;
- compress the spring by alternately tight-
ening the nuts, until the spring raises from the
shock absorber flange.
Dismount:
- the shock absorber upper nut and lock
nut;
- the shock absorber lower lock nut.
Rotate the shock absorber and remove it from
the lower joint.
Push the shock absorber rod.
Dismount the “ device – spring – shock ab-
sorber “ assembly.
31
FRONT BEARING ELEMENTS
31 - 31
FRONT SHOCK ABSORBER
R
EMOUNTING
Grease the threaded parts of the shock absorber with special MoS2 grease.
Place the “ device – spring – shock absorber “ assembly.
Fully screw the shock absorber into the lower joint.
Pull the shock absorber rod by means of the SUS 513 device.
Position the rubber buffers and the crossbar.
Tighten the upper nut at the required moment.
Tighten the lock nut.
Tighten at the required couple:
- the lower lock nut;
- the stabilizer rod shaft nut.
Depress the spring and dismount the SUS 478 device.
Mount the wheel.
Lower the vehicle from the elevator.
Remove the PF 509 support crossbar.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст