Daewoo Nubira. Manual — part 88

9B – 26

I

LIGHTING SYSTEMS

DAEWOO V–121 BL4

Step

No

Yes

Value(s)

Action

15

Repair the open circuit between the hazard switch
and fuses F3 or EF12.
Is the repair complete?

System OK

16

With the hazard switch disconnected, use an ohm-
meter to check for an open circuit between blinker
unit terminal 49 and hazard switch connector termi-
nal 7.
Is there an open circuit?

Go to Step 17

Go to Step 18

17

Repair the open circuit between the hazard switch
and the blinker unit.
Is the repair complete?

System OK

18

1. Remove the hazard switch.
2. Turn the hazard switch OFF.
3. Use an ohmmeter to check for continuity be-

tween terminals 7 and 10.

4. Turn the hazard switch ON.
5. Use an ohmmeter to check for continuity be-

tween terminals 7 and 8.

Does the ohmmeter show the specified value for
both tests?

0

W

Go to Step 20

Go to Step 19

19

Replace the hazard switch.
Is the repair complete?

System OK

20

1. With the hazard switch still removed for testing,

turn the hazard switch to the ON position.

2. Use an ohmmeter to check the continuity be-

tween terminals 5, 6, and 9.

Is there continuity between terminals 5, 6, and 9?

Go to Step 19

Go to Step 21

21

1. Disconnect connector C204.
2. Use an ohmmeter to check the continuity of the

wire between the hazard switch terminal 5 and
C204 terminal 1.

Does the ohmmeter show the value specified?

R

Go to Step 23

Go to Step 22

22

Repair the open wire between the hazard switch and
C204.
Is the repair complete?

System OK

23

Use an ohmmeter to check the continuity of the wire
between the hazard switch terminal 6 and C204 ter-
minal 11.
Does the ohmmeter show the specified value?

R

Go to Step 24

Go to Step 22

24

Repair the open circuit between C204 and the turn
signal bulbs.
Is the repair complete?

System OK

LIGHTING SYSTEMS 9B – 27

DAEWOO V–121 BL4

Hazard Lamps Do Not Operate, Turn Signals Are OK

Step

Action

Value(s)

Yes

No

1

Check fuse EF12.
Is fuse EF12 blown?

Go to Step 2

Go to Step 3

2

1. Check for a short circuit and repair if neces-

sary.

2. Replace the fuse.

Is the repair complete?

System OK

3

Use a voltmeter to check the voltage at fuse EF12.
Is the voltage equal to the specified value?

11–14 v

Go to Step 5

Go to Step 4

4

Repair the power supply circuit to fuse EF12.
Is the repair complete?

System OK

5

1. Disconnect the hazard lamp switch connector.
2. Use a voltmeter to check the voltage at hazard

switch terminal 8.

Is the voltage equal to the specified value?

11–14 v

Go to Step 6

Go to Step 9

6

1. Remove the hazard lamp switch.
2. Turn the hazard lamps ON.
3. Use an ohmmeter to check the resistance be-

tween terminals 7 and 8.

Is the resistance equal to the specified value?

0

W

Go to Step 7

Go to Step 10

7

1. With the hazard lamp switch still removed and

disconnected for testing, turn the hazard lamp
switch to the ON position.

2. Use an ohmmeter to check between terminals

5, 6, and 9.

Is the resistance equal to the specified value?

0

W

Go to Step 8

Go to Step 10

8

Repair the open circuit between the hazard lamp
switch connector and splice S204.
Is the repair complete?

System OK

9

Repair the open circuit between the hazard lamp
switch connector terminal H and fuse EF12.
Is the repair complete?

System OK

10

Replace the faulty hazard lamp switch.
Is the repair complete?

System OK

9B – 28

I

LIGHTING SYSTEMS

DAEWOO V–121 BL4

INTERIOR COURTESY AND LUGGAGE COMPARTMENT

LAMPS

Interior Courtesy Lamp Inoperative

CAUTION : Always make sure there is an electrical
load (lamp bulb, etc.) in any circuit between battery
terminals. Do not make a short circuit between bat-
tery terminals with a jumper wire. Hazardous spark-
ing would result.

Test Description
The number(s) below refer to step(s) on the diagnostic

table.

1. Bulb test. Clip one end of a jumper wire to the neg-

ative battery terminal. Clip the other end of the
jumper wire to the end of the bulb. Take the free
end of the bulb (the end without the jumper at-
tached) and touch it to the positive battery terminal.

Step

Action

Value(s)

Yes

No

1

1. Remove the interior courtesy lamp bulb and

inspect the filament.

2. If the filament is not broken, test the bulb using

the vehicle

’

s battery and a jumper wire.

Does the bulb pass the visual and physical checks?

Go to Step 3

Go to Step 2

2

Replace the bulb.
Is the repair complete?

System OK

3

1. Reinstall the interior courtesy lamp bulb.
2. Check fuse EF29.

Is fuse EF29 blown?

Go to Step 4

Go to Step 5

4

1. Check for a short circuit and repair if neces-

sary.

2. Replace the fuse.

Is the repair complete?

System OK

5

Check fuse EF29.
Is the voltage equal to the specified value?

11–14 v

Go to Step 7

Go to Step 6

6

Repair the open circuit between the battery and fuse
EF29.
Is the repair complete?

System OK

7

1. Disconnect the interior courtesy lamp electrical

connector.

2. Check the voltage at the ORN wire.

Is the voltage equal to the specified value?

11–14 v

Go to Step 8

Go to Step 9

8

Repair the open circuit between fuse EF29 and the
interior courtesy lamp.
Is the repair complete?

System OK

9

Use an ohmmeter to check the resistance between
ground and the BLK wire of the interior courtesy
lamp connector (harness side).
Is the resistance equal to the specified value?

0

Ω

Go to Step 10

Go to Step 11

10

Replace the interior courtesy lamp switch assembly.
Is the repair complete?

System OK

11

Repair the ground circuit for the interior courtesy
lamp.
Is the repair complete?

System OK

LIGHTING SYSTEMS 9B – 29

DAEWOO V–121 BL4

Luggage Compartment Lamp Inoperative

CAUTION : Always make sure there is an electrical
load (lamp bulb, etc.) in any circuit between battery
terminals. Do not make a short circuit between bat-
tery terminals with a jumper wire. Hazardous spark-
ing will result.

Test Description
The number(s) below refer to step(s) on the diagnostic

table.

1. Bulb test. Clip one end of a jumper wire to the neg-

ative battery terminal. Clip the other end of the
jumper wire onto one end of the bulb. Take the free
end of the bulb (the end without the jumper at-
tached) and touch it to the positive battery terminal.

Step

Action

Value(s)

Yes

No

1

1. Remove the luggage compartment lamp bulb

and inspect the filament.

2. If the filament is not broken, test the bulb using

the vehicle

’

s battery and a jumper wire.

Does the bulb pass the visual and physical check?

Go to Step 3

Go to Step 2

2

Replace the bulb.
Is the repair complete?

System OK

3

1. Reinstall the luggage compartment lamp bulb.
2. Check fuse EF29.

Is fuse EF29 blown?

Go to Step 4

Go to Step 5

4

1. Check for a short circuit and repair it, if neces-

sary.

2. Replace the fuse.

Is the repair complete?

System OK

5

Check fuse EF29.
Is the voltage equal to the specified value?

11–14 v

Go to Step 7

Go to Step 6

6

Repair the open circuit between the battery and fuse
EF29.
Is the repair complete?

System OK

7

1. Disconnect the luggage compartment lamp

electrical connector.

2. Check the voltage at the ORN wire.

Does the voltage at the ORN wire equal the specified
value?

11–14 v

Go to Step 8

Go to Step 9

8

Repair the open circuit between fuse EF29 and the
luggage compartment lamp.
Is the repair complete?

System OK

9

1. Reconnect the luggage compartment lamp.
2. Remove the luggage compartment lamp (tail-

gate) switch.

3. With a voltmeter, test the PNK/BLK wire at the

luggage compartment lamp (tailgate) switch.

Is the voltage equal to the specified value?

11–14 v

Go to Step 11

Go to Step 10

10

Repair the open circuit between the luggage
compartment lamp and the luggage compartment
lamp (tailgate) switch.
Is the repair complete?

System OK

11

Use an ohmmeter to check the resistance between
ground and the BLK wire at the luggage compart-
ment (tailgate) lamp switch connector (harness
side).
Is the resistance equal to the specified value?

0

W

Go to Step 12

Go to Step 13