Daewoo Nubira. Manual — part 173
GLASS AND MIRRORS 9L – 7
DAEWOO V–121 BL4
Step
No
Yes
Value(s)
Action
12
Replace the outside rearview mirror switch.
Is the repair complete?
System OK
13
1. On the side which has the inoperative mirror,
remove the black plastic escutcheon from the
trim panel side of the door.
2. Disconnect the outside mirror electrical con-
nector.
3. Turn the ignitionON.
4. At the outsidemirrorconnector, connect a volt-
meterbetween terminal 1 (GRY)and terminal 2
(LTGRN, if testing the left side; orPPL/WHT, if
testing the right side).
5. Operate the in/out adjustment on the switch,
and record the voltage indicated in each switch
position.
6. Connect a voltmeterbetween terminal 1 (GRY)
and terminal 3 (WHT, if testing the left side; or
RED/WHT, if testing the right side).
7. Operate the up/down adjustment on the switch,
and record the voltage indicated in each switch
position.
Does the voltmeter indicate the specified voltage for
each test, with the polarity reversing when the switch
is changed fromin to out, or up to down?
11–14 v
Go to Step 14
Go to Step 15
14
Replace the outside rearview mirror.
Is the repair complete?
System OK
15
1. Remove the retaining screw for the power door
mirror and power window switch assembly.
2. Lift the switch assembly so the connectors on
the underside are visible.
3. Leave the outside mirror disconnected, but do
not disconnect the mirror switch connector.
4. Turn the ignitionON.
5. At themirrorswitch connector, backprobe to
measure the voltage between terminal 1 (GRY)
and terminal 2 (LTGRN, if testing the left side;
or PPL/WHT, if testing the right side).
6. Operate the in/out adjustment on the switch,
and record the voltage indicated in each switch
position.
7. Connect a voltmeterbetween terminal 1 (GRY)
and terminal 3 (WHT, if testing the left side; or
RED/WHT; if testing the right side).
8. Operate the up/down adjustment on the switch,
and record the voltage indicated in each switch
position.
Does the voltmeter indicate the specified voltage for
each test, with the polarity reversing when the switch
is changed fromin to out or up to down?
11–14 v
Go to Step 16
Go to Step 12
16
Repair the open circuit between the mirror switch
and the outside rearview mirror connector.
Is the repair complete?
System OK
9L – 8
I
GLASS AND MIRRORS
DAEWOO V–121 BL4
MAINTENANCE AND REPAIR
ON–VEHICLE SERVICE
WINDSHIELD
Tools Required
J–24402 Glass Sealant Remover
Removal Procedure
1. Remove the cowl vent grille. Refer to Section 9R,
Body Front End.
2. Remove the inside rearview mirror. Refer to”Inside
Rearview Mirror” in this section.
3. Remove the weatherstrip around the windshield.
4. Using the glass sealant remover J–24402, cut the
adhesive around the windshield.
5. Remove the windshield from the vehicle..
6. Using a knife, remove the adhesive from the wind-
shield.
7. Using a knife, remove the adhesive from the wind-
shield frame.
GLASS AND MIRRORS 9L – 9
DAEWOO V–121 BL4
Installation Procedure
1. Install the new weatherstrip to the windshield.
2. Apply tape to the new weatherstrip and the wind-
shield to hold the weatherstrip in place.
3. Apply adhesive primer to the windshield frame and
the perimeter of the windshield.
4. Apply glass adhesive to the windshield frame.
5. Install the windshield into the windshield frame.
6. Reposition the tape over the weatherstrip, the wind-
shield, and the windshield frame to hold the wind-
shield in place.
7. Let the adhesive dry for 24 hours.
8. Remove the tape.
9. Check for waterleaks by pouring water on the wind-
shield. If a leak is found, dry the windshield and fill
the area that leaks with adhesive. If the leak per-
sists, remove the windshield and repeat the entire
procedure.
10. Install the inside rearview mirror. Refer to”Inside
Rearview Mirror” in this section.
11. Install the cowl vent grille. Refer to Section 9R,
Body Front End.
9L – 10
I
GLASS AND MIRRORS
DAEWOO V–121 BL4
REAR WINDOW GLASS
(Notchback Shown, Hatchback and
Wagon Similar)
Tools Required
J–24402 Glass Sealant Remover
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the rear window wiper (wagon only). Refer
to Section 9D, Wipers/Washer Systems.
3. Disconnect the rear window defogger electrical con-
nector.
4. Remove the weatherstrip around the rear window.
5. Using the glass sealant remover J–24402, cut the
adhesive around the rear window.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст