Daewoo Tacuma: Body Repair Manual — part 21
7–4 FENDER, HOOD AND TRUNK LID
2. HOOD
2-1. REPAIR PROCEDURE
1. Remove the related parts.
•
Washer hose and nozzles.
•
Wiring harness and others.
2. Remove the hood.
•
Remove the hood mounting bolts from two hinge
bows.
3. Preparation of the new hood.
•
Preparation of the new hood and check damaged
areas.
Fig. 5
4. Apply the paint.
CAUTION
•
Ventilate when spraying paint. Most paint contains
substances that are harmful if inhaled or swal-
lowed.
Read the paint label before opening paint con-
tainer.
•
Avoid contact with skin. Wear an approved res-
pirator, gloves, eye protection and appropriate
clothing when painting.
•
Paint is flammable. Store in a safe place, and
keep it away from sparks, flames or cigarettes.
5. Preinstall the hood.
•
Fasten to the hood hinges bows at two places
with four bolts, carefully.
Fig. 6
FENDER, HOOD AND TRUNK LID 7–5
•
Close the hood and check the front and rear clear-
ances and level difference of hood, fender and
head lamps.
Fig. 7
6. Tighten fully.
•
After checking and adjusting the mounting posi-
tion, tighten all bolts fully.
7. Install the related parts.
•
Washer hose and nozzles.
•
Install in the reverse order in which they were re-
moved.
8. Check and adjust.
•
Check clearances and level differences.
•
Check the hood locking and unlocking condition.
•
Check spray conditions of washer liquid and ad-
just washer spray nozzles on the hood panel.
7–6 FENDER, HOOD AND TRUNK LID
3
3. TRUNK LID
3-1. REPAIR PROCEDURE
1. Remove the related parts.
•
Wiring harness and solenoid valve.
•
Lock set, latch set and others.
2. Remove the trunk lid.
•
Remove the trunk lid mounting bolts from two
hinge bows.
Fig. 8
3. Preparation of the new trunk lid.
•
Preparation of the new trunk lid and check dam-
aged areas.
4. Apply the paint.
CAUTION
•
Ventilate when spraying paint. Most paint contains
substances that are harmful if inhaled or swal-
lowed.
Read the paint label before opening paint con-
tainer.
•
Avoid contact with skin. Wear an approved res-
pirator, gloves, eye protection and appropriate
clothing when painting.
•
Paint is flammable. Store in a safe place, and
keep it away from sparks, flames or cigarettes.
5. Preinstall the trunk lid.
•
Fasten to the trunk lid hinges bows at two places
with four bolts, carefully.
•
Install bumper.
Fig. 9
BUMPER
4
2
1
(1,2)
(3,4)
FENDER, HOOD AND TRUNK LID 7–7
•
Close the trunk lid and check the clearances and
level difference of trunk lid, side panel outers and
rear combination lamps.
Fig. 10
6. Tighten fully.
•
After checking and adjusting the mounting posi-
tion, tighten all bolts fully.
7. Install the related parts.
•
Wiring harness and solenoid valve.
•
Lock set, latches and linkages.
•
Install in the reverse order in which they were re-
moved.
8. Check and adjust.
•
Clean the trunk compartment.
•
Check clearances and level differences.
•
Check the trunk lid locking and unlocking condi-
tion.
•
Check for water leaks in the trunk compartment.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст