Daewoo Korando. Manual — part 220
PROPELLER SHAFT 3C-5
Inspection Procedure
1. Visual check.
Check the disassembled parts for wear or crack.
Replace them if necessary.
2. Spider outer diameter (mm).
Standard
16.668
Limit
16.647
5. If difficult to remove, clamp the yoke side in a vise and tap
off the needle bearing, using a proper tool.
6. Disassemble the universal joint parts.
l
As axles move up and down, universal joints allow drive
angles to change without binding propeller shaft.
1 Grease Nipple
2 Flange Yoke
3 Spider
4 Seal
5 Needle Roller Bearing
6 Snap Ring
3C-6 PROPELLER SHAFT
3. Clearance between the spider and bearing.
4. Propeller shaft runout
l
Using a dial indicator, measure propeller shaft runout by
turning the shaft. If runout exceeds limit, replace the
propeller shaft or correct it using a press.
Standard
0.03 - 0.098 mm
Limit
0.25 mm
Limit
0.4 mm
5. Universal joint starting torque.
6. Possible cause of vibration.
l
Drift away of balance weights.
l
Excessive runout of the propeller shaft.
l
Using normal bolts.
l
Excessive wear of the universal joint.
l
Sticks in sleeve joint.
l
Drive angle changes in universal joints or cross causes
vibration and can be detected around 60~100 km/h.
Starting Torque
3 - 8 kg
l
cm
PROPELLER SHAFT 3C-7
3. Install the bearing cap to the yoke and insert the spider.
Install the opposite side cap by tapping with a plastic
hammer. Adjust clearance of the spider pin to be within 0.1
mm and install the snap ring.
4. Align the alignment marks and install the front and rear
propeller shaft. Tighten the nuts to the specified torque.
Installation Procedure
Clean the disassembled parts and replace them if damaged.
1. Align the alignment marks of the yoke and assemble the
spider, bearing and snap ring.
2. Apply grease to the inner of the bearing cap of the needle
roller bearing and assemble the needle roller.
Grease
EP #2
SECTION 3D
REAR DRIVE AXLE
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3D-1
General Specifications . . . . . . . . . . . . . . . . . . 3D-1
Fastener Tightening Specifications . . . . . . . . . 3D-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Noise (During Straight Driving) . . . . . . . . . . . . 3D-3
Oil Leakage . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Noise (During Turning) . . . . . . . . . . . . . . . . . . 3D-3
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-4
Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-4
Component Locator . . . . . . . . . . . . . . . . . . . 3D-5
Maintenance and Repair . . . . . . . . . . . . . . . 3D-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3D-6
Axle Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-6
Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3D-11
Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3D-11
LSD (Limited Slip Diffrential) . . . . . . . . . . . . . 3D-16
SPECIFICATIONS
GENERAL SPECIFICATIONS
Axle Shaft Type
Axle Housing Type
Differential
Reduction Ratio
Type
Gear
M/T
M/T
A/T (MB)
M/T
A/T (BTRA)
M/T
A/T (BTRA)
Description
Semi - floating
Salibury (Build-up)
Conventional Type
Hypoid Gear
4.55
4.55
3.73
4.55
5.38
4.27
4.89
Application
661NA
662NA
661LA
662LA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст