Daewoo Musso. Manual — part 210
2C-12 FRONT SUSPENSION
1 Axle Vertical Acceleration Sensor (wheel G
sensor)
Removal & Installation Procedure
1. Disconnect extension wiring connector (2) from the axle
vertical acceleration sensor.
Notice
Installation of wiring connector should be as shown in the
right drawing.
2. Unscrew bolts (3) and remove the axle vertical acceleration
sensor (1).
Notice
When installing the sensor to the bracket, the sensor wiring
should be upward.
3. Installation should follow the removal procedure in the
reverse order.
1
Actuator Connector
2
Axle Vertical Acceleration Sensor Connector
3
Front Hose Mounting Bracket
4
Frame Side Member
AXLE VERTICAL ACCELERATION SENSOR (WHEEL G SENSOR)
2 Extension Wiring
3 Bolt (M6) . . . . . . . . . . . . 20 - 30Nm
FRONT SUSPENSION 2C-13
VERTICAL AND LATERAL SENSOR
Removal & Installation Procedure
1. Disconnect vertical sensor and lateral sensor connectors.
Notice
When connecting the connectors, connector connection of
the lateral sensor (2) should be in the right and connector
connection of the vertical sensor (1) should face downward.
2. Unscrew bolts and remove vertical sensor and lateral sensor.
Installation Notice
1
Body Vertical Acceleration Sensor(Vertical Sensor)
2
Body Lateral Acceleration Sensor (Lateral Sensor)
3. Installation should follow the removal procedure in the
reverse order.
Tightening Torque
20 - 30 Nm
2C-14 FRONT SUSPENSION
ECS (ECU)
1 Electronically Controlled Suspension (ECU)
2 Connector
3 Bolts (2 pieces)
Removal & Installation Procedure
1. Disconnect each connectors from the console box and
remove the console box.
2. Disconnect ECU connector.
3. Unscrew 10mm x 2 bolts and remove ECS (ECU).
4. Installation should follow the removal procedure in the
reverse order.
4 Parking Brake Lever
5 Over Voltage Protection Relay
Type
Spring Type
Coil Spring
Shock Absorber
Stabilizer Type
Description
5-link
Coil Spring
13.8 mm
126.8 mm
384.5 mm
f
139.6 mm
2.58 kg
Cylindrical Reciprocation Type
Torsion Bar Type
SECTION 2D
REAR SUSPENSION
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Wire Diameter (mm)
Diameter (mm)
Free Heigth (mm)
Outer Diameter (mm)
Spring Constant (kg
·
m)
Application
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 2D-1
General Specifications . . . . . . . . . . . . . . . . . . 2D-1
Fastener Tightening Specifications . . . . . . . . . 2D-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 2D-2
Noise (During Straight Driving) . . . . . . . . . . . . 2D-2
Oil Leakage . . . . . . . . . . . . . . . . . . . . . . . . . . 2D-2
Noise (During Turning) . . . . . . . . . . . . . . . . . . 2D-2
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2D-3
Component Locator . . . . . . . . . . . . . . . . . . . 2D-4
Maintenance and Repair . . . . . . . . . . . . . . . 2D-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 2D-5
Rear Suspension(5-Link) . . . . . . . . . . . . . . . . 2D-5
Rear Shock Absorber . . . . . . . . . . . . . . . . . . . 2D-9
FASTENER TIGHTENING SPECIFICATIONS
Application
Upper Nut
Stabilizer Bar Bolt
Lateral Rod Nut
Shock Absorber Mounting Nut Upper
Arm Fixing Nut
N
l
m
16 - 22
30 - 45
150 - 180
50 - 65
150 - 180
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст