Daewoo Musso. Manual — part 140

OM600 ENGINE ELECTRICAL 1E3-7

Removal & Installation Procedure

1. Disconnect the negative terminal of the battery.

2. Disconnect the plug connection (5).

3. OM 662 Engine

Align the groove of cooling fan with bolt (2) (arrow).

4. Remove the bolts (2, 3) and take out the alternator.

5. Installation should follow the removal procedure in the

reverse order.

Tightening Torque

45 Nm

1E3-8 OM600 ENGINE ELECTRICAL

STARTER MOTOR

1 Starter Motor
2 Washer

3 Nut . . . . . . . . . . . . . . . . 15Nm
4 Bolt . . . . . . . . . . . . . . . 48Nm

Removal & Installation Procedure

1. Disconnect the battery terminals.

2. Disconnect the starter motor cable harnesses.

3. Remove the bolts and then remove the starter motor.

4. Installation should follow the removal procedure in the

reverse order.

SECTION 1F1

M162 ENGINE CONTROLS

TABLE OF CONTENTS

CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.

Specifications . . . . . . . . . . . . . . . . . . . . . . . 1F1-2

Fastener Tightening Specifications . . . . . . . . 1F1-2

Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1F1-3

Special Tools Table . . . . . . . . . . . . . . . . . . . . 1F1-3

Schematic and Routing Diagrams . . . . . . . 1F1-4

E32 ECU (HFM) . . . . . . . . . . . . . . . . . . . . . . 1F1-4

E32 ECU (MSE) . . . . . . . . . . . . . . . . . . . . . . 1F1-5

Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6

Self Diagnosis Socket Pin Numbers and

Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6

Self Diagnosis Failure Code . . . . . . . . . . . . . 1F1-7

Test Box Connection . . . . . . . . . . . . . . . . . . 1F1-10

Fuel Injection System Test (MSE3.62) . . . . . 1F1-11

Ignition System Test . . . . . . . . . . . . . . . . . . 1F1-21

Idling Control and Electronic Pedal

System Test . . . . . . . . . . . . . . . . . . . . . . . 1F1-26

Air Conditioner Control System Test . . . . . . 1F1-28

Fuel Pressure and Internal Leakage Test . . 1F1-29

Fuel Pump Test . . . . . . . . . . . . . . . . . . . . . . 1F1-31

Injector Test . . . . . . . . . . . . . . . . . . . . . . . . 1F1-33

Maintenance and Repair . . . . . . . . . . . . . 1F1-35

On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1F1-35

ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-35

Fuel Pressure Regulator . . . . . . . . . . . . . . 1F1-46

Fuel Distributor . . . . . . . . . . . . . . . . . . . . . . 1F1-50

Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-54

Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-57

Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-58

Purge Switchover Valve . . . . . . . . . . . . . . . 1F1-62

Vacuum System . . . . . . . . . . . . . . . . . . . . . 1F1-64

Crankshaft Position Sensor . . . . . . . . . . . . 1F1-65

Camshaft Position Sensor . . . . . . . . . . . . . 1F1-67

Hot Film Air Mass (HFM) Sensor . . . . . . . . . 1F1-69

Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . 1F1-72

Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . 1F1-74

Coolant Temperature Sensor . . . . . . . . . . . 1F1-75

Accelerator Pedal Module . . . . . . . . . . . . . . 1F1-78

1F1-2 M162 ENGINE CONTROLS

SPECIFICATIONS

FASTENER TIGHTENING SPECIFICATIONS

Application

Fuel Return and Supply Line

Fuel Distributor Assembly Bolt

Pressure Test Connector

Fuel Inlet and Outlet Line

Fuel Filter Mounting Bracket Bolt

Crankshaft Position Sensor Bolt

Camkshaft Position Sensor Bolt

Knock Sensor Mounting Bolt

Coolant Temperature Bolt

N

·

m

25 - 30

22.5 - 27.5

21.6 - 26.4

25 - 30

4 - 8

9 - 11

9 - 11

22.5 - 27.5

18 - 22