Daewoo Matiz (2003 year). Manual — part 183
6E – 6 STEERING WHEEL AND COLUMN
Ignition Switch
Condition
Probable Cause
Correction
Electrical System Will
D
Damaged ignition switch.
D
Replace the ignition switch.
Not Function
D
Improperly installed ignition switch.
D
Remove and inspect the ignition
switch.
D
Reinstall the ignition switch.
D
Improperly installed ignition switch electrical
connector.
D
Reconnect the ignition switch
electrical connector.
D
Replace the ignition switch electrical
connector.
Ignition Switch Will
D
Damaged ignition switch.
D
Replace the ignition switch.
Not Turn
D
Improperly installed ignition switch.
D
Remove and inspect the ignition
switch.
D
Reinstall the ignition switch.
Wiper Switch Lever
Condition
Probable Cause
Correction
Switch Inoperative :
D
Damaged wiper switch.
D
Replace the wiper switch.
No I, Low, High, Int
or Wash
D
Improperly installed wiper switch.
D
Remove and inspect the wiper
switch.
D
Reinstall the wiper switch.
STEERING WHEEL AND COLUMN 6E – 7
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
D105A501
D15A502A
DW310–010
STEERING WHEEL
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Tools Required
DW310–010, Steering Wheel Puller
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the SIR module. Refer to Section 8B, Sup-
plemental Inflatable Restraints. (For vehicle with SIR)
3. Remove the steering wheel.
4. Remove the steering wheel horn cover (For vehicle
without SIR) (1).
D
Straighten the bending locking plate (2).
D
Remove the nut (3).
D
Remove the locking plate (4).
D
In order to install the steering wheel correctly,
match–mark the steering column shaft to the
steering wheel (5).
D
Remove the steering wheel using the steering
wheel puller DW310–010 (6).
Important: Be careful not to hit the top of steering col-
umn shaft with hammer during repair work.
D15A503A
Installation Procedure
1. Install the SIR module. Refer to Section 8B, Supple-
mental Inflatable Restraints (For vehicle with SIR).
Important: Align the match marks on the steering wheel
and the steering column shaft.
2. Install the steering wheel with the nut and the locking
plate.
Tighten
Tighten the steering wheel nut to 23–33 N
S
m (17–24
lb-ft).
3. Bend the tabs to secure the locking plate.
4. Install the steering wheel horn cover (For vehicle
without SIR).
5. Connect the negative battery cable.
6E – 8 STEERING WHEEL AND COLUMN
D105A504
STEERING COLUMN COVER
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the screws.
2. Remove the steering column lower and upper cover.
D105A505
Installation Procedure
1. Install the steering column lower and upper cover with
the screws.
D105A506
TURN SIGNAL SWITCH AND LEVER/
WIPER SWITCH AND LEVER
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the steering column cover. Refer to “Steer-
ing Column Cover” in this section.
3. Remove the turn signal switch.
D
Disconnect the turn signal switch by pushing the
locking from the switch housing (1).
D
Disconnect the connector (2).
D105A507
4. Remove the wiper switch.
D
Disconnect the wiper switch by pushing the locking
from the switch housing (1).
D
Disconnect the connector (2).
STEERING WHEEL AND COLUMN 6E – 9
D105A508
Installation Procedure
1. Install the wiper switch.
2. Install the turn signal switch.
3. Install the steering column cover. Refer to “Steering
Column Cover” in this section.
4. Connect the negative battery cable.
D105A509
IGNITION SWITCH
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the steering wheel. Refer to “Steering
Wheel” in this section.
3. Remove the ignition switch.
D
Disconnect the electrical connector (1).
D
Remove the screw (2).
D105A510
Installation Procedure
1. Connect the electrical connector.
2. Install the ignition switch with the screw.
3, Install the steering wheel. Refer to “Steering Wheel”
in this section.
4. Connect the negative battery cable.
D105A511
IGNITION LOCK CYLINDER WITH
IMMOBILIZER
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the steering wheel. Refer to “Steering
Wheel” in this section.
2. Disconnect the electrical connector for the immobiliz-
er detection coil.
3. Remove the lock cylinder.
D
With the key in the ignition, turn to the position des-
ignated I (1).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст