Daewoo Matiz (2003 year). Manual — part 50
1F – 110 ENGINE CONTROLS
DTC P0172 – Fuel Trim System Too Rich
Step
Action
Value(s)
Yes
No
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
Install the scan tool to the Data Link Connector
(DLC).
Turn the ignition ON.
Are any component related Diagnostic Trouble
Codes (DTCs) set?
–
Go to
Applicable DTC
table
Go to Step 3
3
1. With the engine running, operate the vehicle until
the LOOP STATUS indicates closed.
Is the Long Term Fuel Trim value above the
specified value?
30%
Go to Step 4
Go to Step 5
4
1. Turn the ignition switch ON, with the engine OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC as
noted.
Does the Long Term Fuel Trim value above the
specified value while operating under the specified
conditions?
30%
Go to Step 21
Go to Step 5
5
Visually/physically check the air cleaner filter for
excessive dirt or being plugged and repair as
needed.
Is the repair complete?
–
Go to Step 21
Go to Step 6
6
Visually/physically check the air intake system for
collapsed or restricted and repair as needed.
Is the repair complete?
–
Go to Step 21
Go to Step 7
7
Inspect the throttle body inlet for damaged or foreign
objects which may partially block the airflow and
repair as needed.
Is the repair complete?
–
Go to Step 21
Go to Step 8
8
1. Turn the ignition OFF.
2. Inspect the throttle bore, throttle plate and Idle Air
Control (IAC) passages for clocking and foreign
objects and repair as needed.
Is the repair complete?
–
Go to Step 21
Go to Step 9
9
Start the engine with the vehicle in park or neutral
and A/C off and note the idle quality.
Is a low or unsteady idle being experienced?
–
Go to Step 10
Go to Step 12
10
Idle the engine.
Are the IAC counts below the specified value?
100
Go to Step 12
Go to Step 11
11
1. Turn the ignition OFF.
2. Disconnect the Manifold Absolute Pressure
(MAP) sensor electrical connector.
3. Start the engine.
4. Operate the vehicle in Closed Loop while
monitoring the Long Term Fuel Trim value.
Does the Long Term Fuel Trim value increase above
the specified value?
30%
Go to Step 20
Go to Step 12
ENGINE CONTROLS 1F – 111
DTC P0172 – Fuel Trim System Too Rich (Cont’d)
Step
Action
Value(s)
Yes
No
12
Check the IAC valve performance. Refer to “DTC
P0506 Idle Speed RPM Lower Than Desired Idle
Speed” or “DTC P0507 Idle Speed RPM Higher
Than Desired Idle Speed” in this section and repair
as necessary.
Is the repair complete?
–
Go to Step 21
Go to Step 13
13
1. Disconnect the vacuum hose from the fuel
pressure regulator and inspect the hose for the
presence of fuel.
2. If fuel is presence in the vacuum hose, replace
the fuel pressure regulator.
Is the repair complete?
–
Go to Step 21
Go to Step 14
14
1. Turn the ignition ON.
2. Slowly press the acceleration pedal.
Does the Throttle Position (TP) sensor display
increase steady and evenly from its minimum
voltage at closed throttle to its maximum voltage at
Wide-Open Throttle (WOT).
–
Go to Step 15
Go to Step 19
15
1. Perform the Fuel System Diagnosis.
2. If the table isolate a problem, repair as needed.
Is the repair complete?
–
Go to Step 21
Go to Step 16
16
1. Perform the Evaporative Emission (EVAP)
Control System Diagnosis.
2. If the table isolate a problem, repair as needed.
Is the repair complete?
–
Go to Step 21
Go to Step 17
17
1. Perform the Fuel Injector balance Test.
2. If the table isolate a problem, repair as needed.
Is the repair complete?
–
Go to Step 21
Go to Step 18
18
1. Remove the Oxygen Sensor (O2S)
2. Visually/physically inspect the O2S for silicone
contamination.
3. Note: this will be indicated by a powdery white
deposit on the portion of the O2S exposed to the
exhaust stream.
4. If contamination is present on the O2S, find the
source and repair as needed.
Is the repair complete?
–
Go to Step 21
Go to
“Diagnostic
Aids”
19
1. Check the TP sensor mounting screws.
2. If they are too loose or missing tighten or replace
them as needed.
3. If the screws are OK, replace the TP sensor.
Is the repair complete?
–
Go to Step 21
–
20
1. Turn the ignition OFF.
2. Replace the MAP sensor.
Is the repair complete?
–
Go to Step 21
–
1F – 112 ENGINE CONTROLS
DTC P0172 – Fuel Trim System Too Rich (Cont’d)
Step
Action
Value(s)
Yes
No
21
1. Using the scan tool, clear the Diagnostic Trouble
Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?
–
Go to Step 21
Go to Step 2
22
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK
ENGINE CONTROLS 1F – 113
BLANK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст