Hyundai Sonata (2018 year). Instruction — part 28
Instrument panel fuse panel
Fuse Name
Fuse rating
Protected Component
SAFETY WINDOW LH
25A
Driver Safety Power Window Module
P/SEAT PASS
30A
Passenger Seat Manual Switch
P/WDW LH
20A
Power Window Main Switch, Rear Power Window Module LH
Power Window Main Switch, Rear Power Window Module RH, Passenger Door Module,
P/WDW RH
25A
Passenger Power Window Switch
DR LOCK
20A
Door Lock Relay, Door Unlock Relay
S/HEATER FRT
25A
Front Air Ventilation Seat Module, Front Seat Warmer Module
BRAKE SWITCH
10A
Stop Lamp Switch, Immobilizer Module, Smart Key Control Module
8 MODULE
7.5A
BCM, Smart Key Control Module
SAFETY POWER WINDOW
25A
Passenger Safety Power Window Module
RH
SMART KEY
15A
Smart Key Control Module
TRUNK
10A
Trunk Lid Relay, Fuel Filler Door & Trunk Lid Switch
7 MODULE
10A
Digital Clock, Driver/Passenger Door Module
7
Ignition Key Ill. & Door Warning Switch, Front Vanity Lamp Switch LH/RH,
INTERIOR LAMP
10A
Overhead Console Lamp, Room Lamp, Rear Personal Lamp LH/RH, Trunk Room Lamp,
Driver/Passenger Smart Key Outside Handle
2 MEMORY
7.5A
Not used
P/SEAT DRV
30A
Driver Seat Manual Switch, Driver IMS Module
CLUSTER
10A
Instrument Cluster
7-61
Maintenance
Instrument panel fuse panel
Fuse Name
Fuse rating
Protected Component
4 MODULE
10A
Immobilizer Module, Smart Key Control Module
MULTI MEDIA
15A
A/V & Navigation Head Unit
Driver/Passenger Door Module, Driver IMS Module, A/C Control Module,
1 MEMORY
10A
Auto Light & Photo Sensor, Electro Chromic Mirror, Instrument Cluster,
Tire Pressure Monitoring Module, Digital Clock, Wireless Charger, A/V & Navigation Head Unit
S/HEATER RR
25A
Rear Seat Warmer Module
2 SUN ROOF
20A
Panoramic Sunroof Motor
9 MODULE
7.5A
Front Air Ventilation Seat Module, Front Seat Warmer Module, Rear Seat Warmer Module
MDPS
7.5A
MDPS Unit (Column Type/Rack Type)
3 MODULE
10A
BCM, Sport Mode Switch, Stop Lamp Switch
1 MODULE
7.5A
Key Solenoid, Driver/Passenger Door Module
[With Panorama] Panorama Sunroof Motor
1 SUN ROOF
20A
[W/O Panorama] Sunroof Motor
A/CON
7.5A
A/C Control Module, E/R Junction Block (Blower Relay)
A/V & Navigation Head Unit, Digital Clock, USB Charger, BCM, AMP,
2 MODULE
10A
Power Outside Mirror Switch, Wireless Charger, Smart Key Control Module,
Overhead Console Lamp, E/R Junction Block (Power Outlet Relay)
A/BAG IND
7.5A
Instrument Cluster
Multipurpose Check Connector, A/C Control Module, A/V & Navigation Head Unit,
6 MODULE
10A
Front Air Ventilation Seat Module, Front Seat Warmer Module, Rear Seat Warmer Module,
Driver IMS Module, Head Lamp LH/RH (DBL), A/T Shift Lever IND.
AMP
25A
AMP (JBL/MOBIS)
7-62
Instrument panel fuse panel
Fuse Name
Fuse rating
Protected Component
HTD STRG
15A
BCM
Front Console Switch, Tire Pressure Monitoring Module, Lane Keeping Assist Module,
Smart Cruise Control Unit, Fuel Filler Door & Trunk Lid Switch, AEB Module,
5 MODULE
10A
Head Lamp LH/RH (DBL), Rear Parking Assist Sensor LH/RH,
Rear Parking Assist Sensor LH/RH (Center), Blind Spot Detection Radar LH/RH
IG1
25A
PCB Block (Fuse - VACUUM PUMP2/ TCU2/ ECU3/ ABS3)
WASHER
15A
Multifunction Switch (Wiper Low & Washer Switch)
POWER OUTLET
20A
Front Power Outlet
A/BAG
15A
SRS Control Module, Occupant Detection Sensor
[W/O Smart Key & IMMO.] ICM Relay Box (Burglar Alarm Relay)
START
7.5A
[With Smart Key / IMMO.]
Transaxle Range Switch, PCM (G4KJ/G4KH)
10 MODULE
10A
BCM
7
7-63
Maintenance
Engine compartment fuse panel
OLF074028
Inside the fuse/relay box cover, you
can find the fuse/relay label describ-
ing fuse/relay name and capacity.
i
Information
Not all fuse panel descriptions in this
manual may be applicable to your
vehicle; the information is accurate at
OLF077057N
the time of printing. When you inspect
the fuse panel in your vehicle, refer to
the fuse panel label.
7-64
Engine compartment main fuse panel
Fuse Name
Fuse rating
Protected Component
[Without Smart Key] (Start Relay), Ignition Switch,
IG2
30A
[With Smart Key] (Start Relay), PCB Block (IG2 Relay)
3 TCU
40A
[G4FJ - DCT] TCM
BLOWER
40A
(Blower Relay)
MULTI
1 ABS
40A
ESC Module
FUSE
REAR HEATED
50A
(Rear Heated Relay)
(TYPE A)
1 B+
50A
Smart Junction Block (IPS2 (4CH), IPS3 (4CH))
1 COOLING FAN
50A
[G4KH/G4FJ] (Cooling Fan Relay), [G4KJ] (Cooling Fan Relay)
2 COOLING FAN
60A
[G4KH/G4FJ] (Cooling Fan Relay)
1 MDPS
80A
MDPS Unit (Column Type)
2 ABS
30A
ESC Module, Multipurpose Check Connector
IG1
40A
[Without Smart Key] Ignition Switch, [With Smart Key] PCB Block (IG1/ACC Relay)
4 TCU
40A
[G4FJ - DCT] TCM
3 POWER OUTLET
40A
(Power Outlet Relay)
7
MULTI
Smart Junction Block (IPS1 (4CH), IPS4 (4CH), IPS5 (4CH), IPS6 (2CH), IPS7 (1CH),
2 B+
50A
FUSE
Fuse - AMP)
(TYPE B)
5 B+
60A
PCB Block (Engine Control Relay, Fuse - TUC1, ECU1, HORN, AMS, WIPER)
Smart Junction Block (Power Window Relay, Fuse - SAFETY POWER WINDOW LH,
1 B+
60A
P/SEAT PASS,SAFETY POWER WINDOW RH, P/SEAT DRV, MODULE1, P/WDW LH,
P/WDW RH, TRUNK, S/HEATER RR, SUNROOF2, SUNROOF1)
2 MDPS
100A
MDPS Unit (Rack Type)
7-65
Maintenance
Engine compartment main fuse panel
Fuse Name
Fuse rating
Protected Component
3 E-CVVT
20A
[G4KJ/G4KH] PCM
2 E-CVVT
20A
[G4KJ/G4KH] PCM
FUEL PUMP
20A
(Fuel Pump Relay)
H/LAMP HI
20A
[With HID] (Head Lamp High Relay)
1 VACUUM PUMP
20A
[G4KH/G4FJ] Vacuum Pump
FUSE
1 E-CVVT
40A
[G4KJ/G4KH] (E-CVVT Relay)
Smart Junction Block (Leak Current Auto-cut Device Fuse - INTERIOR LAMP,
4 B+
40A
MULTI MEDIA, MEMORY1, Fuse - DOOR LOCK, S/HEATER FR, BRAKE SWITCH,
SMART KEY, MODULE10)
A/CON
10A
A/C Control Module
HEATED MIRROR
10A
ECM (G4FJ), A/C Control Module, Drover/Passenger Power Outside Mirror
7-66
Engine compartment main fuse panel - PCB Block
Fuse Name
Fuse rating
Protected Component
2 VACUUM PUMP
10A
[G4KH/G4FJ] Vacuum Pump, Vacuum Switch
3 ECU
10A
PCM/ECM
1 POWER OUTLET
20A
Front Cigarette Lighter & Power Outlet #2
FUEL PUMP
20A
Fuel Pump Relay
HORN
20A
Horn Relay, ICM Relay Box (Burglar Alarm Horn Relay)
WIPER
30A
Front Wiper (Low) Relay, Front Wiper (High) Relay
2 TCU
15A
Transmission Range Switch, TCM (G4FJ-DCT)
3 ABS
10A
ESC Module
2 POWER OUTLET
20A
Rear Power Outlet
Transmission Range Switch, PCM (G4KJ/G4KH-A/T), TCM (G4FJ-DCT),
B/UP LAMP
10A
FUSE
Electro Chromic Mirror, Rear Combination Lamp (IN) LH/RH
1 SENSOR
15A
Oxygen Sensor (Up/Down)
Purge Control Solenoid Valve, Canister Close Valve, RCV Control Solenoid Valve,
Fuel Pump Relay, E/R Junction Block (Cooling Fan High Relay, Fuel Pump Relay),
2 SENSOR
15A
7
[G4KJ/G4KH] Variable Intake Solenoid Valve, Oil Control Valve (Exhaust),
[G4FJ] Oil Control Valve #1/#2 (Intake/Exhaust)
1 ECU
10A
PCM/ECM
1 TCU
10A
PCM (G4KJ/G4KH-A/T), TCM (G4FJ-DCT)
1 ECU
10A
PCM/ECM
IGN COIL
20A
Ignition Coil #1/#2/#3/#4
INJECTOR
15A
Not Used
AMS
10A
Battery Sensor
7-67
Maintenance
LIGHT BULBS
Consult an authorized HYUNDAI
Absorbent (if equipped)
WARNING
dealer to replace most vehicle light
This vehicle contains a dehumidify-
bulbs. It is difficult to replace vehicle
ing dehumidifier inside the headlamp
•
Prior to replacing a lamp,
light bulbs because other parts of the
to mitigate the blurring of the head-
vehicle must be removed before you
depress the foot brake, move
lamp due to moisture.
the shift lever into P
(Park)
can get to the bulb. This is especially
apply the parking brake, place
The desiccant is a consumable part
true for removing the headlamp
the igntion switch to the
and its performance may change
assembly to get to the bulb(s).
LOCK/OFF position, and take
depending on the usage time or envi-
Removing/installing the headlamp
the key with you when leaving
ronment.
assembly can result in damage to
the vehicle to avoid sudden
If the inside of the headlamp contin-
the vehicle.
movement of the vehicle and
ues to become cloudy due to mois-
to prevent possible electric
ture, we recommend that you consult
i
Information
shock.
an authorized HYUNDAI dealer.
After heavy driving, rain or washing,
•
Be aware the bulbs may be
The desiccant is a consumable part
headlamp and trunk lenses could
hot and may burn your fin-
and cannot be guaranteed.
appear frosty. This condition is caused
gers.
by the temperature difference
between the lamp inside and the out-
side temperature. This is similar to the
condensation on your windows inside
your vehicle during the rain and does-
n’t indicate a problem with your vehi-
cle. If the water leaks into the lamp
bulb circuitry, have your vehicle
checked by an authorized HYUNDAI
dealer.
7-68
Headlamp, Position Lamp,
(4) Front side marker
Turn Signal Lamp and
(5) Daytime running lamp/
Side Marker Light Bulb
Parking lamp
Replacement
■ Type A
OLMB073042L
Headlamp (Halogen bulb)
OLF077050
WARNING
■ Type B
• Handle halogen bulbs with
care. Halogen bulbs contain
pressurized gas that will pro-
duce flying pieces of glass
7
that could cause injuries if
broken.
• Wear eye protection when
changing a bulb. Allow the
bulb to cool down before han-
OLF077051
dling it.
(1) Headlamp (Low)
(2) Headlamp (High)
(3) Turn signal lamp
7-69
Maintenance
• Always handle them carefully, and
■ High beam
5. Unsnap the headlamp bulb retain-
avoid scratches and abrasions. If
ing wire by pressing the end and
the bulbs are lit, avoid contact with
pushing it upward.
liquids.
6. Remove the bulb from the head-
• Never touch the glass with bare
lamp assembly.
hands. Residual oil may cause the
7. Install a new headlamp bulb and
bulb to overheat and burst when lit.
snap the headlamp bulb retaining
• A bulb should be operated only
wire into position by aligning the
when installed in a headlamp.
wire with the groove on the bulb.
• If a bulb becomes damaged or
OLF077070
8. Connect the headlamp bulb sock-
cracked, replace it immediately
■ Low beam
et-connector.
and carefully dispose of it.
9. Install the headlamp bulb cover by
turning it clockwise.
i
Information
The headlamp aiming should be
adjusted after an accident or after the
headlamp assembly is reinstalled at an
authorized HYUNDAI dealer.
OLF077069
1. Open the hood.
Headlamp (LED type)
2. Disconnect the negative battery
If the light bulb does not operate, we
cable.
recommend that the system be
3. Remove the headlamp bulb cover
checked by an authorized HYUNDAI
by turning it counterclockwise.
dealer.
4. Disconnect the headlamp bulb
socket-connector.
7-70
5. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
7. Push the socket into the assembly
and turn the socket clockwise.
OLF077052N
OLF077074
Turn signal lamp
Side marker
1. Open the hood.
1. Open the hood.
2. Disconnect the negative battery
2. Disconnect the negative battery
cable.
cable.
3. Remove the socket from the
3. Remove the socket from the
assembly by turning the socket
assembly by turning the socket
counterclockwise until the tabs on
counterclockwise until the tabs on
the socket align with the slots on
the socket align with the slots on
7
the assembly.
the assembly.
4. Remove the bulb from the socket
4. Remove the bulb from the socket
by pressing it in and rotating it
by pulling out the bulb.
counterclockwise until the tabs on
5. Insert a new bulb.
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7-71
Maintenance
Daytime running lamp/
Side Repeater Lamp
Rear Combination Light Bulb
Position lamp
Replacement
Replacement
If the LED lamp does not operate,
have the vehicle checked by an
authorized HYUNDAI dealer.
OLF077053
OLF077060
If the LED lamp does not operate,
(1) Stop/Tail lamp
have the vehicle checked by an
(2) Turn signal lamp
authorized HYUNDAI dealer.
(3) Tail lamp
(4) Back-up lamp
(5) Rear side marker (LED)
(if equipped)
7-72
Stop/Tail lamp and rear side mark-
er (LED type)
Stop/Tail lamp
If the LED lamp does not operate,
Turn Signal lamp
have the vehicle checked by an
authorized HYUNDAI dealer.
OLF047062N
OLF074063
Stop/Tail lamp and Turn signal
3. Remove the socket from the
lamp (Bulb type)
assembly by turning the socket
counterclockwise until the tabs on
1. Open the trunk lid.
the socket align with the slots on
2. Remove the service cover by
the assembly.
pulling it out.
4. Remove the bulb from the socket by
pressing it in and rotating it coun-
terclockwise until the tabs on the
7
bulb align with the slots in the sock-
et. Pull the bulb out of the socket.
5. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
7-73
Maintenance
High Mounted Stop Lamp
OLF077064N
OLF077065
Backup lamp and Tail lamp
4. Remove the bulb by pulling it
OLF077055
straight out.
1. Open the trunk.
1. Remove the rear seat cushion
5. Insert a new bulb by inserting it
2. Loosen the retaining screw of the
assembly.
into the socket and rotating it until
trunk lid cover and then remove
it locks into place.
2. Remove the rear seat back
the cover.
assembly.
6. Install the socket into the assem-
3. Disconnect the connector and
bly by aligning the tabs on the
3. Slightly remove the rear door
then remove the screws by turning
socket with the slots in the assem-
weather-strip.
the screws counterclockwise.
bly. Push the socket into the
4. Remove the rear door scuff trim.
assembly and turn the socket
5. Remove the rear pillar trim.
clockwise.
6. Remove the rear seat belt lower
7. Reinstall the trunk lid cover by
anchor.
pushing in the screw.
7-74
7. Remove the rear package tray
License Plate Light Bulb
Interior Light Bulb
trim.
Replacement
Replacement
8. Remove the high mounted stop
Map lamp and Room lamp
lamp after disengaging the mount-
■ Map lamp - with sunroof
ing clip.
9. Install a new LED lamp.
OLF077066
OLF076080N
■ Room lamp - with sunroof
1. Loosen the lens retaining screws
with a philips head screwdriver.
2. Remove the lens.
3. Remove the bulb by pulling it
straight out.
7
4. Install a new bulb.
5. Reinstall the lens securely with
the lens retaining screws.
OLF077071
If the LED lamp does not operate,
have the vehicle checked by an
authorized HYUNDAI dealer.
7-75
Maintenance
Map lamp, Room lamp, Vanity mirror lamp and Luggage room lamp
1. Using a flat-head screwdriver,
gently pry the lens from the interi-
■ Map lamp - without sunroof
■ Vanity mirror lamp
or light housing.
2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interi-
or light housing notches and snap
the lens into place.
If the lamps do not operating, have
the vehicle checked by an authorized
HYUNDAI dealer.
OTL045276
OLF074069
■ Room lamp - without sunroof
■ Trunk room lamp
NOTICE
Use care not to dirty or damage
lenses, lens tabs, and plastic
housings.
OLF074082N
OLF074056
7-76
APPEARANCE CARE
Exterior Care
Finish maintenance
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water.
Exterior general caution
Washing
Do not allow soap to dry on the fin-
To help protect your vehicle’s finish
It is very important to follow the label
ish.
directions when using any chemical
from rust and deterioration, wash it
thoroughly and frequently at least
cleaner or polish. Read all warning
WARNING
and caution statements that appear
once a month with lukewarm or cold
water.
on the label.
After washing the vehicle, test
If you use your vehicle for off-road
the brakes while driving slowly
driving, you should wash it after each
High-pressure washing
to see if they have been affected
off-road trip. Pay special attention to
by water before getting on the
•
When using high-pressure wash-
the removal of any accumulation of
road. If braking performance is
ers, make sure to maintain suffi-
salt, dirt, mud, and other foreign
impaired, dry the brakes by
cient distance from the vehicle.
materials. Make sure the drain holes
applying them lightly while
Insufficient clearance or excessive
in the lower edges of the doors and
maintaining a slow forward
pressure can lead to component
rocker panels are kept clear and
speed.
damage or water penetration.
clean.
•
Do not spray the camera, sensors
Insects, tar, tree sap, bird droppings,
or its surrounding area directly with
industrial pollution and similar
a high pressure washer. Shock
deposits can damage your vehicle’s
applied from high pressure water
finish if not removed immediately.
may cause the device to not oper-
7
Even prompt washing with plain
ate normally.
water may not completely remove all
•
Do not bring the nozzle tip close to
these deposits. A mild soap, safe for
boots (rubber or plastic covers)or
use on painted surfaces, should be
connectors as they may be dam-
used.
aged if they come into contact with
high pressure water.
7-77
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст