Hyundai Elantra GT (2018 year). Instruction — part 15
Paddle shifter (if equipped)
With the shift lever in the D posi-
i
Information
tion
•
Only the seven forward gears can be
The paddle shifter will operate when
selected in Manual Shift Mode. To
the vehicle speed is more than
reverse or park the vehicle, move
6 mph (10 km/h).
the shift lever to the R (Reverse) or
P (Park) position as required.
Pull the [+] or [-] paddle shifter once
to shift up or down one gear and the
•
Downshifts are made automatically
system changes from automatic
when the vehicle slows down. When
mode to manual mode.
the vehicle stops, 1st gear is automat-
ically selected.
When the vehicle speed is lower
than 6 mph (10 km/h), if you depress
•
When the engine rpm approaches
the accelerator pedal for more than 5
the red zone the transmission will
OPD056015
seconds or if you move the shift lever
upshift automatically.
from Manual Shift mode to D (Drive),
5
The paddle shifter is functional when
•
If the driver presses the lever to
the system changes from manual
the shift lever is in the D (Drive) posi-
+ (Up) or - (Down) position, the
mode to automatic mode.
tion or the manual shift mode.
transmission may not make the
requested gear change if the next
With the shift lever in the manual
gear is outside of the allowable
engine rpm range. The driver must
shift mode
execute upshifts in accordance with
Pull the [+] or [-] paddle shifter once
road conditions, taking care to keep
to shift up or down one gear.
the engine rpms below the red zone.
i
Information
If the [+] and [-] paddle shifters are
pulled at the same time, gear change
may not occur.
5-31
Driving your vehicle
Shift-lock system
Shift-lock release
5. Move the shift lever.
For your safety, the automatic trans-
6. Remove the tool from the shift-
mission has a shift-lock system
lock override access hole then
which prevents shifting the transmis-
install the cap.
sion from P (Park) into R (Reverse)
unless the brake pedal is depressed.
If you need to use the shift-lock
To shift the transmission from P
release, have your vehicle inspected
(Park) into R (Reverse):
by an authorized HYUNDAI dealer
1. Depress and hold the brake pedal.
immediately.
2. Start the engine or place the igni-
tion switch in the ON position.
Parking
3. Move the shift lever.
Always come to a complete stop and
OPDE056122
continue to depress the brake pedal.
If the shift lever cannot be moved from
Move the shift lever into the P (Park)
the P (Park) position into R (Reverse)
position, apply the parking brake,
position with the brake pedal
and place the ignition switch in the
depressed, continue depressing the
LOCK/OFF position. Take the key
brake, and then do the following:
with you when exiting the vehicle.
1. Place the ignition switch in the
LOCK/OFF position.
Moving up a steep grade from a
2. Apply the parking brake.
standing start
3. Carefully remove the cap (1) cov-
To move up a steep grade from a
ering the shift-lock release access
standing start, depress the brake
hole.
pedal, shift the shift lever to D
4. Insert a tool (e.g. flathead screw-
(Drive). Depress the accelerator
driver) into the access hole and
pedal gradually while releasing the
press down on the tool.
brake pedal.
5-32
Good Driving Practices
•
When driving in Manual Shift
WARNING
mode, slow down before shifting to
•
Never move the shift lever from P
a lower gear. Otherwise, the lower
(Park) or N (Neutral) to any other
When you stay in the vehicle
gear may not be engaged if the
with the engine running, be
position with the accelerator pedal
engine rpms are outside of the
depressed.
careful not to depress the accel-
allowable range.
erator pedal for a long period of
•
Never move the shift lever into P
•
Always apply the parking brake
time. The engine or exhaust
(Park) when the vehicle is in
when leaving the vehicle. Do not
system may overheat and start
motion.
depend on placing the transmis-
a fire.
Be sure the vehicle is completely
sion in P (Park) to keep the vehicle
The exhaust gas and the
stopped before you attempt to shift
from moving.
exhaust system are very hot.
into R (Reverse) or D (Drive).
•
Exercise extreme caution when
Keep away from the exhaust
•
Do not move the shift lever to N
driving on a slippery surface. Be
system components.
(Neutral) when driving. Doing so
especially careful when braking,
Do not stop or park over flam-
may result in an accident because
5
accelerating or shifting gears. On a
mable materials, such as dry
of a loss of engine braking and the
slippery surface, an abrupt change
grass, paper or leaves. They
transmission could be damaged.
in vehicle speed can cause the
may ignite and cause a fire.
•
Do not drive with your foot resting
drive wheels to lose traction and
on the brake pedal. Even light, but
may cause loss of vehicle control
consistent pedal pressure can
resulting in an accident.
result in the brakes overheating,
•
Optimum vehicle performance and
brake wear and possibly even
economy is obtained by smoothly
brake failure.
depressing and releasing the
•
Depressing both accelerator and
accelerator.
brake pedals at the same time can
trigger logic for engine power
reduction to assure vehicle decel-
eration. Vehicle acceleration will
resume after the brake pedal is
released.
5-33
Driving your vehicle
WARNING
(Continued)
•
In the event your vehicle
To reduce the risk of SERIOUS
leaves the roadway, do not
INJURY or DEATH:
steer sharply. Instead, slow
•
ALWAYS wear your seatbelt.
down before pulling back into
In a collision, an unbelted
the travel lanes.
occupant is significantly more
•
HYUNDAI recommends you
likely to be seriously injured
follow all posted speed limits.
or killed than a properly belt-
ed occupant.
•
Avoid high speeds when cor-
nering or turning.
•
Do not make quick steering
wheel movements, such as
sharp lane changes or fast,
sharp turns.
•
The risk of rollover is greatly
increased if you lose control
of your vehicle at highway
speeds.
•
Loss of control often occurs if
two or more wheels drop off
the roadway and the driver
over steers to reenter the
roadway.
(Continued)
5-34
BRAKING SYSTEM
Power Brakes
WARNING
(Continued)
Your vehicle has power-assisted
•
Wet brakes may impair the
brakes that adjust automatically
Take the following precautions:
vehicle's ability to safely slow
through normal usage.
•
Do not drive with your foot
down; the vehicle may also
If the engine is not running or is
pull to one side when the
resting on the brake pedal.
turned off while driving, the power
This will create abnormal high
brakes are applied. Applying
assist for the brakes will not work.
the brakes lightly will indicate
brake temperatures, exces-
You can still stop your vehicle by
sive brake lining and pad
whether they have been
applying greater force to the brake
affected in this way. Always
wear, and increased stopping
pedal than typical. The stopping dis-
distances.
test your brakes in this fash-
tance, however, will be longer than
ion after driving through deep
•
When descending down a
with power brakes.
water. To dry the brakes, light-
long or steep hill, move the
When the engine is not running, the
ly tap the brake pedal to heat
gear shift lever to Manual
up the brakes while maintain-
reserve brake power is partially
Shift Mode and manually
5
depleted each time the brake pedal
ing a safe forward speed until
downshift to a lower gear in
brake performance returns to
is applied. Do not pump the brake
order to control your speed
pedal when the power assist has
normal. Avoid driving at high
without using the brake pedal
speeds until the brakes func-
been interrupted.
excessively. Applying the
tion correctly.
Pump the brake pedal only when
brakes continuously will
necessary to maintain steering con-
cause the brakes to overheat
trol on slippery surfaces.
and could result in a tempo-
rary loss of braking perform-
ance.
(Continued)
5-35
Driving your vehicle
Disc Brakes Wear Indicator
Parking Brake
(hand type, if equipped)
When your brake pads are worn and
new pads are required, you will hear
a high pitched warning sound from
your front or rear brakes. You may
hear this sound come and go or it
may occur whenever you depress
the brake pedal.
Note that some driving conditions or
climates may cause a brake squeal
when you first apply (or lightly apply)
OPD056017
the brakes. This is normal and does
not indicate a problem with your
To release:
brakes.
Firmly depress the brake pedal.
OPD056016
While pressing the release button
Always set the parking brake before
NOTICE
(1), slightly pull up on the parking
leaving the vehicle. To apply the
brake lever then lower the parking
To avoid costly brake repairs, do
parking brake:
brake lever (2).
not continue to drive with worn
Firmly depress the brake pedal.
brake pads.
If the parking brake does not release
Pull up the parking brake lever as far
or does not release all the way, have
as possible.
your vehicle checked by an author-
i
Information
ized HYUNDAI dealer.
Always replace brake pads as com-
WARNING
plete front or rear axle sets.
To reduce the risk of SERIOUS
INJURY or DEATH, do not oper-
ate the parking brake while the
vehicle is moving except in an
emergency situation. It could
damage the brake system and
lead to an accident.
5-36
NOTICE
Check the Parking
WARNING
Brake Warning Light
•
Do not apply the accelerator
by placing the ignition
•
Whenever leaving the vehicle
pedal while the parking brake is
switch to the ON posi-
or parking, always come to a
engaged. If you depress the
tion
(do not start the
complete stop and continue to
accelerator pedal with the park-
engine).
ing brake engaged, warning will
depress the brake pedal. Move
This light will be illuminated when the
the shift lever into P
(Park)
sound. Damage to the parking
parking brake is applied with the igni-
position, then apply the park-
brake may occur.
tion switch in the START or ON posi-
ing brake, and place the igni-
•
Driving with the parking brake
tion.
tion switch in the LOCK/OFF
on can overheat the braking sys-
position.
Before driving, be sure the parking
tem and cause premature wear
brake is released and the Brake
Vehicles with the parking
or damage to brake parts. Make
Warning Light is OFF.
brake not fully engaged are at
sure the parking brake is
If the Parking Brake Warning Light
risk for moving inadvertently
released and the Brake Warning
5
and causing injury to yourself
Light is off before driving.
remains on after the parking brake is
released while engine is running,
or others.
there may be a malfunction in the
•
When parking on an incline,
brake system. Immediate attention is
block the wheels to prevent
necessary.
the vehicle from rolling down.
If at all possible, cease driving the
•
NEVER allow anyone who is
vehicle immediately. If that is not pos-
unfamiliar with the vehicle to
sible, use extreme caution while
touch the parking brake. If the
operating the vehicle and only con-
parking brake is released
tinue to drive the vehicle until you
unintentionally, serious injury
can reach a safe location.
may occur.
•
Only release the parking
brake when you are seated
inside the vehicle with your
foot firmly on the brake pedal.
5-37
Driving your vehicle
Electronic Parking Brake (EPB)
Releasing the parking brake
WARNING
(if equipped)
Applying the parking brake
To reduce the risk of SERIOUS
INJURY or DEATH, do not oper-
ate the EPB while the vehicle is
moving except in an emergency
situation. It could damage the
brake system and lead to an
accident.
OPD056019
To release the EPB (Electronic
OPD056018
Parking Brake), press the EPB
switch in the following condition:
To apply the EPB
• Place the Engine Start/Stop button
(Electronic Parking Brake):
in the ON position.
1. Depress the brake pedal.
• Depress the brake pedal.
2. Pull up the EPB switch.
Make sure the Parking Brake
Make sure the Parking Brake
Warning Light goes off.
Warning Light comes on.
5-38
To release EPB (Electronic Parking
• Automatic transmission/Dual clutch
i
Information - Manual trans-
Brake) automatically:
transmission vehicle
mission
•
Shift lever in P (Park)
1. Ensure seat belts are fastened
A vehicle towing a trailer on a hill or
and the doors, hood and liftgate
With the engine running depress
on an incline may slightly roll back-
are closed.
the brake pedal and shift out of P
wards when starting the vehicle. To
(Park) to R (Reverse) or D (Drive).
2. With the engine running, depress
prevent the situation follow the below
the brake pedal and shift out of P
•
Shift lever in N (Neutral)
instructions.
(Park) to R
(Reverse) or D
With the engine running depress
1. Depress the clutch pedal and select
(Drive).
the brake pedal and shift out of N
a gear.
3. Depress the accelerator pedal.
(Neutral) to R
(Reverse) or D
2. Keep pulling up the EPB switch.
(Drive).
Make sure the Parking Brake
3. Depress the accelerator pedal and
Warning light goes off.
•
Manual transmission vehicle
slowly release the clutch pedal.
1. Ensure seat belts are fastened
4. If the vehicle starts off with enough
5
and the doors, hood and liftgate
i
Information
driving power release the EPB
are closed.
• For your safety, you can engage the
switch.
2. With the engine running, depress
EPB even though the Engine Stop/
Do not follow the above procedure
the clutch pedal and move the
Start button is in the OFF position,
when driving on a flat level ground.
shift lever to 1 (First) gear or R
but you cannot release it.
The vehicle may suddenly move for-
(Reverse).
• For your safety, depress the brake
ward.
3. Depress the accelerator pedal
pedal and release the parking brake
while releasing the clutch pedal.
manually with the EPB switch when
you drive downhill or when backing
up the vehicle.
5-39
Driving your vehicle
NOTICE
Warning messages
WARNING
• If the parking brake warning
light is still on even though the
•
Whenever leaving the vehicle
EPB has been released, have the
or parking, always come to a
system checked by an author-
complete stop and continue
ized HYUNDAI dealer.
to depress the brake pedal.
• Do not drive your vehicle with
Move the shift lever into the P
the EPB applied. It may cause
(Park) position, press the EPB
excessive brake pad and brake
switch, and press the Engine
rotor wear.
Start/Stop button to the OFF
position. Take the Smart Key
with you when exiting the
EPB (Electronic Parking Brake)
OPDE056130
vehicle.
may be automatically applied
To release EPB, fasten seatbelt,
Vehicles not fully engaged in
when:
close door, hood and tailgate
P
(Park) with the parking
• Requested by other systems
• If you try to drive with the EPB
brake set are at risk for mov-
• If the driver turns the engine off
ing inadvertently and causing
applied, a warning will sound and a
while Auto Hold is operating, EPB
injury to yourself or others.
message will appear.
will be automatically applied.
•
NEVER allow anyone who is
• If the driver's seat belt is unfas-
unfamiliar with the vehicle to
tened and the engine hood or lift-
touch the EPB switch. If the
gate is opened, a warning will
EPB is released unintentional-
sound and a message will appear.
ly, serious injury may occur.
• If there is a problem with the vehi-
•
Only release the EPB when
cle, a warning may sound and a
you are seated inside the
message may appear.
vehicle with your foot firmly
If the situation occurs, depress the
on the brake pedal.
brake pedal and release EPB by
pressing the EPB switch.
5-40
■ Type A
■ Type B
■ Type A
■ Type B
NOTICE
• Do not apply the accelerator
pedal while the parking brake is
engaged. If you depress the
accelerator pedal with the EPB
engaged, a warning will sound
and a message will appear.
Damage to the parking brake
may occur.
• Driving with the parking brake
on can overheat the braking sys-
OTLE055028/OLFH044408L
OLF054131N/OLF044411N
tem and cause premature wear
AUTO HOLD deactivating.
Parking brake automatically locked
or damage to brake parts. Make
Press brake pedal
If the EPB is applied while Auto Hold
sure the EPB is released and the
5
Parking Brake Warning Light is
When the conversion from Auto Hold
is activated, a warning will sound and
off before driving.
to EPB is not working properly a
a message will appear.
warning will sound and a message
will appear.
i
Information
• A clicking sound may be heard
while operating or releasing the
EPB. These conditions are normal
and indicate that the EPB is func-
tioning properly.
• When leaving your keys with a
parking attendant or assistant,
make sure to inform him/her how to
operate the EPB.
5-41
Driving your vehicle
EPB malfunction indicator
The EPB malfunction indicator may
Emergency braking
(if equipped)
illuminate when the ESC indicator
If there is a problem with the brake
comes on to indicate that the ESC is
pedal while driving, emergency brak-
■ Type A
■ Type B
not working properly, but it does not
ing is possible by pulling up and
indicate a malfunction of the EPB.
holding the EPB switch. Braking is
possible only while you are holding
NOTICE
the EPB switch. However, braking
distance will be longer than normal.
•
If the EPB warning light is still
on, have the system checked by
an authorized HYUNDAI dealer.
WARNING
OPD056021/OPD056074
•
If the parking brake warning
light does not illuminate or
Do not operate the parking
This warning light illuminates if the
brake while the vehicle is mov-
blinks even though the EPB
Engine Start/Stop button is changed
ing except in an emergency sit-
switch was pulled up, the EPB
to the ON position and goes off in
uation. It could damage the
may not be applied.
approximately 3 seconds if the sys-
brake system and lead to a
•
If the parking brake warning
tem is operating normally.
severe accident.
light blinks when the EPB warn-
If the EPB malfunction indicator
ing light is on, press the switch,
remains on, comes on while driving,
and then pull it up. Repeat this
i
Information
or does not come on when the
one more time. If the EPB warn-
Engine Start/Stop button is changed
During emergency braking, the park-
ing does not go off, have the
to the ON position, this indicates that
ing brake warning light will illumi-
system checked by an author-
the EPB may have malfunctioned.
nate to indicate that the system is
ized HYUNDAI dealer.
If this occurs, have the system
operating.
checked by an authorized HYUNDAI
dealer.
5-42
NOTICE
Auto Hold
White
The Auto Hold maintains the vehicle
If you continuously notice a noise
in a standstill even though the brake
or burning smell when the EPB is
pedal is not depressed after the driv-
used for emergency braking, have
er brings the vehicle to a complete
system checked by an authorized
stop by depressing the brake pedal.
HYUNDAI dealer.
Green
To apply :
When the EPB (Electronic Parking
Brake) does not release
If the EPB does not release normal-
White
OPD056023
ly, we recommend that you contact
an authorized HYUNDAI dealer by
2. When you stop the vehicle com-
loading the vehicle on a flatbed tow
pletely by depressing the brake
5
truck and have the system checked.
pedal, the Auto Hold maintains the
brake pressure to hold the vehicle
stationary. The indicator changes
from white to green.
3. The vehicle will remain stationary
even if you release the brake
OPD056022
pedal.
1. With the driver's door, engine
4. If EPB is applied, Auto Hold will be
hood and liftgate closed, fasten
released.
the driver's seat belt or depress
the brake pedal and then press
the
[AUTO HOLD] switch. The
white AUTO HOLD indicator will
come on and the system will be in
the standby position.
5-43
Driving your vehicle
To release :
To cancel :
WARNING
•
If you press the accelerator pedal
with the shift lever in D (Drive), R
Light off
To prevent, unexpected and sud-
(Reverse) or manual shift mode,
den vehicle movement, ALWAYS
the Auto Hold will be released
press your foot on the brake
automatically and the vehicle will
pedal to cancel the Auto Hold
start to move. The AUTO HOLD
before you:
indicator changes from green to
- Drive downhill.
white.
- Drive the vehicle in R (Reverse).
•
If the vehicle is restarted using the
cruise control toggle switch (RES+
- Park the vehicle.
or SET-) while Auto Hold and cruise
control is operating, the Auto Hold
OPD056024
will be released regardless of
accelerator pedal operation. The
1. Depress the brake pedal.
AUTO HOLD indicator changes
2. Press the [AUTO HOLD] switch.
from green to white. (if equipped
The AUTO HOLD indicator will turn
with cruise control system)
off.
WARNING
When the AUTO HOLD is auto-
matically released by depress-
ing the accelerator pedal, always
take a look around your vehicle.
Slowly depress the accelerator
pedal for a smooth start.
5-44
(Continued)
i
Information
WARNING
In these cases, the parking brake
•
The Auto Hold does not operate
warning light comes on, the AUTO
when:
• Depress the accelerator pedal
HOLD indicator changes from
slowly when you start the
- The driver's seat belt is unfastened
green to white, and a warning sound
vehicle.
and driver's door is opened
and a message will appear to inform
- The engine hood is opened
you that EPB has been automatical-
• For your safety, cancel the
ly engaged. Before driving off again,
Auto Hold when you drive
- The shift lever is in P (Park) or R
press foot brake pedal, check the
downhill, back up the vehicle
(Reverse)
surrounding area near your vehicle
or park the vehicle.
- The EPB is applied
and release parking brake manually
•
For your safety, the Auto Hold auto-
with the EPB switch.
NOTICE
matically switches to EPB when:
• While operating Auto Hold, you may
- The driver's seat belt is unfastened
hear mechanical noise. However, it is
If there is a malfunction with the
driver's door or engine hood open
5
and driver's door is opened
normal operating noise.
detection system, the Auto Hold
- The engine hood is opened with the
may not work properly.
shift lever is in D (Drive)
NOTICE
Contact an authorized HYUNDAI
- The vehicle stops for more than 10
If the AUTO HOLD indicator
dealer.
minutes
changes to yellow, the Auto Hold
- The vehicle stands on a steep slope
is not working properly. Contact
- The vehicle moves several times
an authorized HYUNDAI dealer.
(Continued)
5-45
Driving your vehicle
Warning messages
■ Type A
■ Type B
■ Type A
■ Type B
■ Type A
■ Type B
OTLE055028/OLFH044408L
OLF054127N/OLF044407N
AUTO HOLD deactivating.
Press brake pedal to deactivate
OLF054131N/OLF044411N
Press brake pedal
AUTO HOLD
Parking brake automatically locked
When the conversion from Auto Hold
If you did not apply the brake pedal
When the EPB is applied from Auto
to EPB is not working properly a
when you release the Auto Hold by
Hold, a warning will sound and a
warning will sound and a message
pressing the [AUTO HOLD] switch, a
message will appear.
will appear.
warning will sound and a message
will appear.
When this message is displayed, the
Auto Hold and EPB may not operate.
For your safety, depress the brake
pedal.
5-46
Anti-lock Brake System (ABS)
(Continued)
Drive your vehicle at reduced
WARNING
speeds during the following
conditions:
An Anti-Lock Braking System
(ABS) or an Electronic Stability
• Rough, gravel or snow-cov-
ered roads.
Control (ESC) system will not
prevent accidents due to
• On roads where the road sur-
improper or dangerous driving
face is pitted or has different
maneuvers. Even though vehi-
surface height.
cle control is improved during
• Tire chains are installed on
OPDE056108
emergency braking, always
your vehicle.
maintain a safe distance
AUTO HOLD conditions not met.
The safety features of an ABS
between you and objects ahead
Close door and hood, then fasten
or ESC equipped vehicle should
5
of you. Vehicle speeds should
seatbelt
not be tested by high speed
always be reduced during
When you press the [AUTO HOLD]
driving or cornering. This could
extreme road conditions. The
switch, if the driver's door and engine
endanger the safety of yourself
braking distance for cars
hood are not closed or the driver's
or others.
equipped with ABS or ESC may
seat belt is unfastened, a warning
be longer than for those without
will sound and a message will
these systems in the following
appear on the LCD display. At this
ABS is an electronic braking system
road conditions.
moment, press the [AUTO HOLD]
that helps prevent a braking skid.
(Continued)
ABS allows the driver to steer and
button after closing the driver's door
and engine hood, and fastening the
brake at the same time.
seat belt.
5-47
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст