Hyundai Getz: Body Repair Manual — part 32
134
ZINC-PHOSPHA
ZINC-PHOSPHA
ZINC-PHOSPHA
ZINC-PHOSPHA
ZINC-PHOSPHATE CO
TE CO
TE CO
TE CO
TE COA
A
A
A
AT & CA
T & CA
T & CA
T & CA
T & CATIONIC ELECTR
TIONIC ELECTR
TIONIC ELECTR
TIONIC ELECTR
TIONIC ELECTRODEPOSITION PRIMER
ODEPOSITION PRIMER
ODEPOSITION PRIMER
ODEPOSITION PRIMER
ODEPOSITION PRIMER
In order to improve the adhesion of the paint coat on the steel panel, and also to improve the corrosion resistance, the entire
body is coated with a film of Zinc-phosphate and a cationic electrodeposition primer.
CORROSION PROTECTION - Zinc-phosphate coat & cationic eletrodeposition primer
Body steel panel
Zinc-phosphate film
Cationic electrodeposition primer
COR-0020
135
ANTI-CORROSION PRIMER
ANTI-CORROSION PRIMER
ANTI-CORROSION PRIMER
ANTI-CORROSION PRIMER
ANTI-CORROSION PRIMER
An anti-corrosion primer has been applied to the side sill outer panel for the purposes of corrosion prevention and abrasion
protection. If this panel is replaced, apply an anti-corrosion primer between the undercoat and the intermediate coat, as
shown in the following illustrations.
Rock panel primer (Thickness 180
µ
~ 200 µ
)
CORROSION PROTECTION - Anti-corrosion primer
TB-133-2
A
A'
Í
Í
SECTION A-A'
Front & rear door outer
panel
Side sill outer panel
133-1
Door inner panel
136
CORROSION PROTECTION - Antivibration pads
ANTIVIBRATION PADS-LOCATION & SECTION
SECTION A-A'
SECTION B-B'
SECTION C-C'
SECTION D-D'
ANT-0002
ANT-0003
ANT-0004
ANT-0005
ANT-0001
Ï
A
A'
Ï
C
Í
C'
Í
Ï
B
B'
Ï
Ï
D
D'
Ï
84152-1C000
84186-1C000
84156-1C000
84187-1C000
84151-1C000
84155-1C000
84185-1C000
Dash panel
Dash lower reinforcement
84151/52-1C000
Center floor panel
Center floor panel
84151/52-1C000
Front seat cross member
84155/56-1C000
3mm
15mm
15mm
Rear floor extension
7mm
Rear floor panel
84155/56-1C000
Rear floor front
cross member
84156/55-1C000
Center floor panel
Rear floor side
front member
Center floor side
member
Side sill inner
panel
44.5mm
137
CORROSION PROTECTION - Attachment of antivibration pads
ANT-0001
ATTACHMENT OF ANTIVIBRATION PADS
Antivibration pads are attached to the upper surface of the floor and at the interior side of the dash panel in order to absorb
vibrations and shut out exhaust gas heat. If these antivibration pads are peeled off in the course of replacement or repair
of a welded panel, cut and attach replacement material (in the shape shown in the figure).
1.
Heat the "antivibration pad" with a blow drier to soften it.
2.
Align the antivibration pad layer in the position where it is to be
installed, and then press it down with a roller or a block of wood
so that it adheres well.
NOTE
An infrared lamp can also be used to heat both the antivibration
pad layer and the body panels(be sure to wear gloves).
COR-0006
COR-0007
84152-1C000
84186-1C000
84156-1C000
84187-1C000
84151-1C000
84155-1C000
84185-1C000
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст