Hyundai Santa Fe (2006 year). Manual — part 599
FLA -462
FUEL SYSTEM
4)
Read "DTC Status" parameter.
SCMF16159L
5)
Is parameter displayed "Present fault"?
YES
▶ Go to "Terminal and connector inspection" procedure.
NO
▶ Fault is intermittent caused by poor contact in the sensor’s and/or PCM’s connector or was repaired and PCM
memory was not cleared. Thoroughly check connectors for looseness, poor connection, ending, corrosion, con-
tamination, deterioration, or damage. Repair or replace as necessary and go to "Verification of Vehicle Repair"
procedure.
TERMINAL AND CONNECTOR INSPECTION
E2E5805E
1.
Many malfunctions in the electrical system are caused by poor harness and terminals. Faults can also be caused by
interference from other electrical systems, and mechanical or chemical damage.
2.
Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or
damage.
3.
Has a problem been found?
YES
▶ Repair as necessary and go to "Verification of Vehicle Repair" procedure
NO
▶ Substitute with a known-good PCM and check for proper operation. If the problem is corrected,replace PCM and
then go to "Verification of Vehicle Repair" procedure.
NOTE
There is a memory reset function on scantool that can erase optional parts automatically detected and memorized
by PCM. After testing PCM on the vehicle, use this function to reuse the PCM on the others
DTC TROUBLESHOOTING PROCEDURES
FLA -463
VERIFICATION OF VEHICLE REPAIR
EDF49698
After a repair, it is essential to verify that the fault has been corrected.
1.
Monitor and record the Freeze Frame Data for the Diagnostic Trouble Code(DTC) which has been diagnosed.
2.
Using a Scantool, Clear the DTCs
3.
Operate the vehicle within conditions noted in the freeze frame data or enable conditions
4.
Monitor that all rediness test have been verified as " Complete "
5.
Are any DTCs present ?
YES
▶ Go to the applicable troubleshoooting procedure.
NO
▶ System is performing to specification at this time.
FLA -464
FUEL SYSTEM
DTC P0602 EEPROM-PROGRAMING ERROR
COMPONENT LOCATION
E6E49C3C
Refer to DTC P0601.
GENERAL DESCRIPTION
EECB64CE
Refer to DTC P0601.
DTC DESCRIPTION
E0CE496F
If CPU software version dose not accord with main CPU, PCM sets P0602.
DTC DETECTING CONDITION
E88A3072
Item
Detecting Condition
Possible cause
DTC Strategy
• Check internal CPU
Enable Conditions
• -
Threshold value
• The version discordance among PCU
S/W or Calibration
Diagnosis Time
• Continuous
MIL On Condition
• 1 driving cycle
• Faulty PCM
MONITOR DTC STATUS
ED153DB8
Refer to DTC P0601.
TERMINAL AND CONNECTOR INSPECTION
EB336C96
Refer to DTC P0601.
VERIFICATION OF VEHICLE REPAIR
E499B411
Refer to DTC P0601.
DTC TROUBLESHOOTING PROCEDURES
FLA -465
DTC P0604 INTERNAL CONTROL MODULE RANDOM ACCESS MEMORY
(RAM) ERROR
COMPONENT LOCATION
ECDD00AC
Refer to DTC P0601.
GENERAL DESCRIPTION
EC8E0935
Refer to DTC P0601.
DTC DESCRIPTION
E7CA500D
If the RAM in PCM has errors, PCM sets P0604 and MIL(Malfunction Indication Lamp) turns on.
DTC DETECTING CONDITION
E848AF67
Item
Detecting Condition
Possible cause
DTC Strategy
• Check internal CPU
Enable Conditions
• -
Threshold value
• RAM has errors
Diagnosis Time
• Continuous
MIL On Condition
• 1 driving cycle
• Faulty PCM
MONITOR DTC STATUS
ECC7C404
Refer to DTC P0601.
TERMINAL AND CONNECTOR INSPECTION
E6886EBD
Refer to DTC P0601.
VERIFICATION OF VEHICLE REPAIR
EF1A07CB
Refer to DTC P0601.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст