Hyundai Santa Fe (2006 year). Manual — part 719
MT -36
MANUAL TRANSAXLE (M5GF2)
M14
4
5
3
2
6
*
v
5.Center
2.Ground
4.S2
3.S1
SCMMT6209L
CAUTION
The above value is only for reference.
The actual value may differ from it according to various engine condition.
4.
Is voltage display near the specified value?
YES
▶ Go to " Steering angle sensor ground harness open circuit inspection " procedure.
NO
▶ Check for Steering angle sensor Reference harness.
▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.
STEERING ANGLE SENSOR GROUND HARNESS OPEN CIRCUIT INSPECTION
E8D94F1B
1.
Ignition OFF, Engine "OFF".
2.
TCCU, Steering angle sensor connector : Connect.
3.
Measure resistance between terminal 2 of Steering angle sensor harness connector and chassis ground.
Specification : 1Ω below
M14
4
5
3
2
6
*
Ω
5.Center
6.Reference
4.S2
3.S1
SCMMT6210L
TRANSFER CASE ASSEMBLY
MT -37
CAUTION
The above value is only for reference.
The actual value may differ from it according to various engine condition.
4.
Is resistance display near the specified value?
YES
▶ Go to " Steering angle sensor #1 ,short to signal line ground Inspection " procedure.
NO
▶ Check for open circuit of Steering angle sensor ground harness.
▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.
SIGNAL CITCUIT INSPECTION
EA133810
STEERING ANGLE SENSOR #1 ,SHORT TO SIGNAL LINE GROUND INSPECTION
1.
Ignition OFF, Engine "OFF".
2.
TCCU, Steering angle sensor connector : Disconnect.
3.
Measure resistance between terminal 3 of Steering angle sensor harness connector and chassis ground.
Specification : ∝ Ω
M14
4
5
3
2
6
*
Ω
5.Center
6.Reference
2.Ground
4.S2
SCMMT6211L
CAUTION
The above value is only for reference.
The actual value may differ from it according to various engine condition.
4.
Is resistance display near the specified value?
YES
▶ Go to " Steering angle sensor #1 signal line open Inspection " procedure.
NO
▶ Check for short to ground circuit of Steering angle sensor #1Signal circuit.
▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.
MT -38
MANUAL TRANSAXLE (M5GF2)
STEERING ANGLE SENSOR #1 SIGNAL LINE OPEN INSPECTION
1.
Ignition OFF, Engine "OFF".
2.
TCCU, Steering angle sensor connector : Disconnect.
3.
Measure resistance between terminal 3 of Steering angle sensor harness connector and terminal 23 of TCCU har-
ness connector.
Specification : 1Ω
M14
1
14
15
16
*
*
*
*
21
*
23
24
25
26
*
3
4
5
*
*
*
*
10
11
12
13
C258
4
5
3
2
6
*
Ω
11.Center
12.Ground
24.S2
25.Reference
5.Center
6.Reference
2.Ground
4.S2
SCMMT6212L
CAUTION
The above value is only for reference.
The actual value may differ from it according to various engine condition.
4.
Is resistance display near the specified value?
YES
▶ Substitute with a known-good TCCU or Steering angle sensor and check for proper operation.
▶ If the problem is corrected, replace TCCU and then go to "Verification of Vehicle Repair" procedure.
NO
▶ Check for open circuit of Steering angle sensor #1 Signal circuit.
▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.
TRANSFER CASE ASSEMBLY
MT -39
VERIFICATION OF VEHICLE REPAIR
EB22A662
1.
Connect scan tool and select "Diagnostic Trouble Codes(DTCs)" mode.
2.
Using scantool, Clear DTC.
3.
Operate the vehicle within DTC Enable conditions in General information.
4.
Are any DTCs present ?
YES
▶ Go to the applicable troubleshooting procedure.
NO
▶ System is performing to specification at this time.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст