Hyundai Santa Fe (2006 year). Manual — part 58
AT -184
AUTOMATIC TRANSAXLE (F4A51)
INSPECTION
EFB6BAFB
1.
Remove the oil temperature sensor(A).
A
EKRF009D
2.
Measure the resistance between the terminal 1 and 2
of the sensor connector.
Temp.[ C( F)]
Resistance(KΩ )
0(32)
100(212)
18.6
0.63
EKRF009E
3.
If the value is out of the specfication, replace the oil
temperature sensor.
AUTOMATIC TRANSAXLE CONTROL SYSTEM
AT -185
TRANSAXLE RANGE (TR)
SWITCH
DESCRIPTION
E88015D4
INHIBITOR SWITCH
- Type: Rotary contact type
- Range of temperature : -40 C∼145 C(-40 F~293 F)
D
N
R
P
Front of vehicle
EKRF018H
INHIBITOR SWITCH - CONTINUITY CHECK(SPORTS
MODE)
Range
P
R
N
D
Terminal Number
1
2
3
4
5
6
7
8
9
10
EKRF018I
REPLACEMENT
EE7E45CD
1.
Pull up the parking brake.
2.
Position the shift lever in ’N’ range.
3.
Remove the air cleaner assembly.
4.
Remove the battery.
5.
Remove the battery tray.
6.
Remove the inhibiter switch connector.
7.
Remove the shift cable mounting nut(A).
A
EKRF008E
8.
Remove the inhibiter switch loosening the mounting
bolts.
9.
Refering to ’INSPECTION’, check for continuity. If
there is an error, replace the inhibiter switch.
EKRF008F
10. After tightening the shift cable mounting nut, connect
the inhibiter switch.
11. Install the battery, battery tray and the air cleaner as-
sembly.
AT -186
AUTOMATIC TRANSAXLE (F4A51)
INSPECTION
E5BFD847
1.
Check for the starter motor when the ignition switch
is at ’START’ position and the shift lever at ’P’ or ’N’
range.
2.
Check for the rear lamp when the ignition switch if it
does not work properly.
3.
Check for the inhibiter switch if it does not work prop-
erly.
4.
If the inhibiter switch is not fixed in a proper position,
reassemble it in the right position.
5.
Re-check 1 and 2 procedures.
6.
Using a scan tool, confirm the DTCs.
7.
Disconnect the battery (-) terminal and the inhibiter
switch.
8.
Check for continuity between terminals at the switch
connector.
Range
P
R
N
D
Terminal Number
1
2
3
4
5
6
7
8
9
10
EKRF008G
7
1 2 3 4 5 6
8
9 10
P
R
N
D
EKRF008H
9.
If there is not continuity between the terminals in the
table above for each switch position, replace the in-
hibiter switch.
ADJUSTMENT
EB9F50D8
1.
Set the select lever to the "N" position.
2.
Loosen the control cable to manual control lever cou-
pling nut to free the cable and lever.
3.
Set the manual control lever to the neutral position.
A
10~12 Nm
(1.0~1.2 kgf.m,
7~8 lb-ft)
EKRF009A
4.
Loosen the transaxle range switch body mounting
bolts and then turn the transaxle range switch body
so the hole in the end of the manual control lever and
the hole (cross section A-A in the figure) in the flange
of the transaxle range switch body flange are aligned.
AUTOMATIC TRANSAXLE CONTROL SYSTEM
AT -187
5.
Tighten the transaxle range switch body mounting
bolts to the specified torque. Make sure at this time
that the position of the switch body did not move.
TORQUE :
10∼12Nm (1.0~1.2kgf.m, 7~8lb-ft)
Mounting bolts
Manual control
lever
Hole in end
Hole in
flange
Section A-A
Manual control
lever
Transaxle range
switch body
A
A
10~12 Nm
(1.0~1.2 kgf.m,
7~8 lb-ft)
EKRF009B
6.
Gently pull the transmission control cable in the direc-
tion of the arrow, and then tighten the adjusting nut.
A
10~12 Nm
(1.0~1.2 kgf.m,
7~8 lb-ft)
EKRF090A
7.
Check that the select lever is in the "N" position.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст