Hyundai Santa Fe (2006 year). Manual — part 482
FL -538
FUEL SYSTEM
REPLACEMENT
E16A29BC
CAUTION
After replacing (an) injector(s), MUST input the in-
jector data (7 digit) into the ECM.
1.
Turn ignition switch OFF.
2.
Disconnect the negative (-) battery cable.
3.
Replace the injector with a new one according to the
"REMOVAL" and "INSTALLATION" procedures.
4.
Connect a scan tool to Data Link Connector (DLC).
5.
Connect the negative (-) battery cable.
6.
Turn ignition switch on.
7.
Select "ENGINE (DIESEL)".
SCMFL6114L
8.
Select "INJECTOR SPECIFIC DATA".
SCMFL6142L
9.
Press "ENTER" key.
1. HYUNDAL VEHICLE DIAGNOSIS
SCMFL6143L
10. Input the injector data (7 digit) written on the top of
each injector with function keys ([F1] ~ [F6]) and num-
ber keys.
1.10. INJECTOR SPECIFIC DATA
1.10. INJECTOR SPECIFIC DATA
SCMFL6144L
FUEL DELIVERY SYSTEM-DIESEL
FL -539
11. Wait 10 seconds after displaying "WRITING COM-
PLETE", turn ignition switch OFF.
NOTE
When "WRITING FAIL" is displayed on the scan tool,
input injector data (7 digits) of each cylinder into a new
ECM again starting from 6th step.
1.10. INJECTOR SPECIFIC DATA
SCMFL6145L
FL -540
FUEL SYSTEM
INSPECTION
E67C26FA
USING HI-SCAN(PRO)
TEST MODE
• COMPRESSION TEST
• IDLE SPEED COMPARISON
• INJECT QUANTITY COMPARISON
TEST PROCEDURE
1.
Connect Scan tool to the DLC and select "Vehicle"
and "Engine Test Function".
1. HYUNDAI/KIA VEHICLE DIAGNOSIS
MODEL : VEHICLE NAME
SYSTEM : ENGINE(DIESEL)
01. DIAGNOSISTIC TROUBLE CODE
02. CURRENT DATA
03. FLIGHT RECORD
04. ACTUATION TEST
05. SIMU-SCAN
06. IDENTIFICATION CHECK
07. ENGINE TEST FUNCTION
08. DATA SETUP(UNIT CONV.)
EFQG090A
2.
Information for ECM version is displayed as below.
1.7. COMPRESSION TEST
SYSTEM IMFORMATION
P/N : ***** - *****
S/W : ********
This function is available
If you ready, press [ENTER].
1.7. COMPRESSION TEST
SYSTEM IMFORMATION
P/N : ***** - *****
S/W : ********
This function is not available.
Not all ECM version support
this function
If you ready, press [ENTER].
<Available system>
<Not available system>
LFIF660B
3.
After pressing "[ENTER]" select "COMPRESSION
TEST" mode and press "[ENTER]".
1.7. COMPRESSION TEST
01. COMPRESSION TEST
02. IDLE SPEED COMPARISON
03. INJECT. QUANTITY COMPARISON
LFIF660D
FUEL DELIVERY SYSTEM-DIESEL
FL -541
4.
Set the test condition described as below screen and
then, crank engine. When engine stop message be-
ing appeared, stop cranking.
7.1. COMPRESSION TEST
This test is used for detecting
cylinder specific engine speed
without injection.
* Test condition
- Shift lever : P or N
- Engine : Stop (IGN. ON)
- Electrical Load : OFF
If you ready, now cranking, and stop
cranking when stop message appear on
the screen. Press [ENTER].
LFIF660E
5.
Press "ANAL" and the test result is appeared.
7.1 COMPRESSION TEST
Cylinder engine speed(RPM)
#1
When the stop message appear, stop cranking.
ANAL
356
356
356
356
357
356
355
355
356
356
356
356
355
356
355
357
356
356
355
355
355
355
356
355
356
356
355
355
#2
#3
#4
LFIF660F
NOTE
During cranking engine does not start.
7.1 COMPRESSION TEST
Cylinder engine speed(RPM)
#1
356
356
356
356
357
356
355
355
356
356
356
356
355
356
355
357
356
356
355
355
355
355
356
355
356
356
355
355
#2
AVG
HELP
#3
#4
Data scanning button
LFIF660G
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст