Hyundai Santa Fe (2006 year). Manual — part 746
RT -26
RESTRAINTS
REMOVAL
E41D5D56
1.
Disconnect the battery negative cable and wait for at
least 3 minutes before beginning work.
2.
Remove the following parts. (Refer to BD group)
-
Side trim, Roof trim
3.
Disconnect the Curtain Airbag harness connector.
SCMRT6009D
4.
After loosening the mounting bolts(10EA) remove the
curtain airbag.
SCMRT6511D
INSTALLATION
E50B5670
1.
Disconnect the battery negative cable and wait for at
least three minutes.
2.
Remove the ignition key from the vehicle.
3.
Install a Curtain Airbag (CAB) on the mounting
bracket.
4.
Tighten the CAB mounting bolts (10EA).
Tightening torque
: 1.1 ~ 1.5 kgf.m(10.9 ~ 14.7 Nm, 8.0 ~ 10.8 lb.ft)
CAUTION
• Never twist the airbag module when installing
it. If the module is twisted, airbag module may
operate abnormally.
5.
Connect the CAB connector.
6.
Install the following parts. (Refer to BD group)
-
Side trim, Roof trim
7.
Reconnect the battery negative cable.
8.
After installing the Curtain Airbag (CAB), confirm
proper system operation:
• Turn the ignition switch ON; the SRS indicator
light should be turned on for about six seconds
and then go off.
SEAT BELT PRETENSIONER
RT -27
SEAT BELT PRETENSIONER
SEAT BELT PRETENSIONER
DESCRIPTION
E4167EBA
The Seat Belt Pretensioners (BPT) are installed inside
Center Pillar (LH & RH). When a vehicle crashes with a
certain degree of frontal impact, the pretensioner seat belt
helps to reduce the severity of injury to the front seat oc-
cupants by retracting the seat belt webbing. This prevents
the front occupants from thrusting forward and hitting the
steering wheel or the instrument panel when the vehicle
crashes.
CAUTION
Never attempt to measure the circuit resistance of
the Seat Belt Pretensioner (BPT) even if you are
using the specified tester. If the circuit resistance
is measured with a tester, the pretensioner will
be ignited accidentally. This will result in serious
personal injury.
COMPONENTS
E13C3CFE
Seat Belt Retractor Pretensioner (BPT)
Center Pillar
SCMRT6503L
RT -28
RESTRAINTS
REMOVAL
E3B165BB
1.
Disconnect the battery negative cable, and wait for at
least three minutes before beginning work.
2.
Remove the door scuff trim. (Refer to BD group)
3.
Remove the center pillar trim. (Refer to BD group)
4.
Remove the lower anchor bolt.
5.
Remove the upper anchor bolt.
6.
Disconnect the Seat Belt Pretensioner connector.
7.
Loosen the Seat Belt Pretensioner mounting bolt and
remove the Seat Belt Pretensioner.
SCMRT6011D
INSTALLATION
E3B35607
1.
Disconnect the battery negative cable and wait for at
least three minutes.
2.
Remove the ignition key from the vehicle.
3.
Install the Seat Belt Pretensioner (BPT) with a bolt.
Tightening torque
: 4.0 ~ 5.5 kgf.m (39.2 ~ 53.9 Nm, 28.9 ~ 39.8 lb.ft)
4.
Install the upper and lower anchor bolts.
Tightening torque (Seat Belt Anchor Bolt)
: 4.0 ~ 5.5 kgf.m (39.2 ~ 53.9 Nm, 28.9 ~ 39.8 lb.ft)
5.
Install the center pillar trim.
6.
Install the door scuff trim.
7.
Reconnect the battery negative cable.
8.
After installing the Seat Belt Pretensioner (BPT), con-
firm proper system operation:
• Turn the ignition switch ON; the SRS indicator
light should be turned on for about six seconds
and then go off.
SRS CONTROL SYSTEM
RT -29
SRS CONTROL SYSTEM
FRONT IMPACT SENSOR (FIS)
DESCRIPTION
EBEE040F
The front impact sensor (FIS) is installed in the side mem-
ber. They are remote sensors that detect acceleration due
to a collision at its mounting location. The primary purpose
of the Front Impact Sensor (FIS) is to provide an indication
of a collision. The Front Impact Sensor(FIS) sends accel-
eration data to the SRSCM.
COMPONENTS
E603A5DC
Front Impact Sensor
SCMRT6505L
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст