Hyundai Santa Fe (2006 year). Manual — part 194
IMMOBILIZER CONTROL SYSTEM
BE -237
1.3 TEACHING
2st KEY TEACHING
COMPLETED
CODE : 234567
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : LEARNT
SCMBE6557L
2)
PCM(ECM) virgin status.
After replacing new "PCM(ECM)" scantool dis-
plays that PCM(ECM) is virgin status in Key
Teaching mode.
"VIRGIN" status means that PCM(ECM) has not
matched any PIN code before.
1.3 TEACHING
INPUT PIN OF SIX
FIGURE AND PRESS [ENTER] KEY
CODE : 234567
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6558L
1.3 TEACHING
1st KEY TEACHING
ARE YOU SURE ? [Y/N]
CODE : 234567
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6559L
1.3 TEACHING
1st KEY TEACHING
COMPLETED
CODE : 234567
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6560L
1.3 TEACHING
2st KEY TEACHING
ARE YOU SURE ? [Y/N]
CODE : 234567
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6561L
1.3 TEACHING
2st KEY TEACHING
COMPLETED
CODE : 234567
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6562L
BE -238
BODY ELECTRICAL SYSTEM
2.
User Password Teaching Procedure
The user password for limp home is taught at the ser-
vice station. The owner of the vehicle can select a
number with four digits.
User password teaching is only accepted by a "learnt"
PCM(ECM). Before first teaching of user password to
an PCM(ECM), the status of the password is "virgin"
No limp home function is possible.
The teaching is started by ignition on, with a valid
key and sending the user password by tester. After
successful teaching, the status of the user password
changes from "virgin" to "learnt"
The learnt user password can also be changed. This
can be done if the user password status is "learnt"
and the tester sends authorization of access, either
the old user password or the vehicle specific data.
After correct authorization, the PCM(ECM) requests
the new user password. The status remains "learnt"
and the new user password will be valid for the next
limp home mode.
If incorrect user passwords or wrong vehicle specific
data have been sent to the PCM(ECM) three times,
the PCM(ECM) will reject the request to change the
password for one hour. This time cannot be reduced
by disconnecting the battery or any other actions. Af-
ter reconnecting the battery, the timer starts again for
one hour.
1)
User password teaching
1. HYUNDAI VEHICLE DIAGNOSIS
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
01. CURRENT DATA
02. PASSWORD TEACHING/CHANGING
03. TEACHING
04. NEUTRAL MODE
05. LIMP HOME MODE
SCMBE6563L
1.2 PASSWORD TEACHING/CHANGING
INPUT NEW PASSWORD OF FOUR
FIGURES AND PRESS [ENTER] KEY
NEW PASSWORD :
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6564L
1.2 PASSWORD TEACHING/CHANGING
INPUT NEW PASSWORD OF FOUR
FIGURES AND PRESS [ENTER] KEY
NEW PASSWORD : 2345
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6565L
1.2 PASSWORD TEACHING/CHANGING
ARE YOU SURE ? [Y/N]
NEW PASSWORD : 2345
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6566L
IMMOBILIZER CONTROL SYSTEM
BE -239
1.2 PASSWORD TEACHING/CHANGING
COMPLETED
PRESS [ESC] TO EXIT
NEW PASSWORD : 2345
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : VIRGIN
SCMBE6567L
※ In case of putting wrong password, retry from
first step after 10 seconds.
2)
User password changing
1. HYUNDAI VEHICLE DIAGNOSIS
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
01. CURRENT DATA
02. PASSWORD TEACHING/CHANGING
03. TEACHING
04. NEUTRAL MODE
05. LIMP HOME MODE
SCMBE6563L
1.2 PASSWORD TEACHING/CHANGING
INPUT OLD PASSWORD OF FOUR
FIGURES AND PRESS [ENTER] KEY
OLD PASSWORD :
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : LEARNT
SCMBE6568L
1.2 PASSWORD TEACHING/CHANGING
INPUT OLD PASSWORD OF FOUR
FIGURES AND PRESS [ENTER] KEY
OLD PASSWORD : 2345
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : LEARNT
SCMBE6569L
1.2 PASSWORD TEACHING/CHANGING
INPUT NEW PASSWORD OF FOUR
FIGURES AND PRESS [ENTER] KEY
NEW PASSWORD : 1234
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : LEARNT
SCMBE6570L
1.2 PASSWORD TEACHING/CHANGING
ARE YOU SURE ? [Y/N]
NEW PASSWORD : 1234
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : LEARNT
SCMBE6571L
BE -240
BODY ELECTRICAL SYSTEM
1.2 PASSWORD TEACHING/CHANGING
COMPLETED
PRESS [ESC] TO EXIT
NEW PASSWORD : 1234
MODEL : SANTAFE
SYSTEM : IMMOBILIZER
STATUS : LEARNT
SCMBE6572L
REPLACEMENT
EE2BB323
PROBLEMS AND REPLACEMENT PARTS:
Problem
Part set
Scan tool
required?
All keys have
been lost
Blank key (4)
YES
Antenna coil unit
does not work
Antenna coil unit
NO
ECM does not work
PCM(ECM)
YES
Ignition switch does
not work
Ignition switch with
Antenna coil unit
YES
Unidentified vehicle
specific data occurs
Key, PCM(ECM)
YES
SMARTRA unit
does not work
SMARTRA unit
NO
REPLACEMENT OF ECM AND SMARTRA
In case of a defective ECM, the unit has to be replaced with
a "virgin" or "neutral" ECM. All keys have to be taught to
the new ECM. Keys, which are not taught to the ECM, are
invalid for the new ECM (Refer to key teaching procedure).
The vehicle specific data have to be left unchanged due to
the unique programming of transponder.
In case of a defective SMARTRA, there is no special pro-
cedure required. A new SMARTRA device simply replaces
the old one. There are no transponder-related data stored
in this device.
1.
Things
to
remember
before
a
replacement
(PCM(ECM))
When installing PCM(ECM) of car "A" on car "B"
All non-virgin PCM(ECM)`s need to be neutralized before
installing on the other vehicles.
Neutralize the PCM(ECM) of car "A"
Installing the PCM(ECM) of car "A" on car "B"
Register the keys with the PIN code of car "B"
Register additional keys (Maximum of keys)
All phases of key registration should be
completed in under 10 seconds
Registration completed
ETBF746A
2.
Things to remember before a replacement (Keys &
Additional registration)
Replace keys & additional registration
Turn the key to the IG ON position
Initialize the PCM(ECM) (Under the Neutral Mode)
Insert the key you want to register and
turn it to the IG ON position
Register additional keys (Maximum of 4 keys)
All phases of key registration should be
completed in under 10 seconds
Registration completed
Register the key (Under the Teaching Mode)
ETBF746B
NOTE
1.
When there is only one key registered and you
wish to register another key, you need to re-reg-
ister the key which was already registered.
2.
When the key #1 is registered and master key #2
is not registered, Put the key #1 in the IG/ON or
the start position and remove it. The engine can
be started with the unregistered key #2.
(Note that key #2 must be used within 10 seconds
of removing key #1)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст