Hyundai Santa Fe (2006 year). Manual — part 485
FLA -6
FUEL SYSTEM
SERVICE STANDARD
E85141FD
Ignition Timing
BTDC 7˚ ± 10˚
Neutral,N,P-range
680 ± 100 rpm
A/CON OFF
D-range
630 ± 100 rpm
Neutral,N,P-range
680 ± 100 rpm
Idle Speed
A/CON ON
D-range
630 ± 100 rpm
TIGHTENING TORQUES
EAEFEBE8
ENGINE CONTROL SYSTEM
Item
kgf·m
N·m
lbf·ft
PCM installation bolts (on upper bracket)
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
PCM upper bracket installation bolts (on air cleaner assembly)
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Camshaft position sensor [Bank 1] installation bolt
0.7 ~ 1.0
6.9 ~ 9.8
5.1 ~ 7.2
Camshaft position sensor [Bank 2] installation bolt
0.7 ~ 1.0
6.9 ~ 9.8
5.1 ~ 7.2
Crankshaft position sensor installation bolt
0.7 ~ 1.0
6.9 ~ 9.8
5.1 ~ 7.2
CVVT Oil control valve [Bank 1] installation bolt
0.8 ~ 1.0
7.8 ~ 9.8
5.8 ~ 7.2
CVVT Oil control valve [Bank 2] installation bolt
0.8 ~ 1.0
7.8 ~ 9.8
5.8 ~ 7.2
CVVT Oil temperature sensor installation
2.0 ~ 4.0
19.6 ~ 39.2
14.5 ~ 28.9
Engine coolant temperature sensor installation
2.0 ~ 4.0
19.6 ~ 39.2
14.5 ~ 28.9
ETC module installation bolt
0.9 ~ 1.1
8.8 ~ 10.8
6.5 ~ 8.0
Heated oxygen sensor (Bank 1 / Sensor 1) installation
3.5 ~ 4.5
34.3 ~ 44.1
25.3 ~ 32.6
Heated oxygen sensor (Bank 1 / Sensor 2) installation
3.5 ~ 4.5
34.3 ~ 44.1
25.3 ~ 32.6
Heated oxygen sensor (Bank 2 / Sensor 1) installation
3.5 ~ 4.5
34.3 ~ 44.1
25.3 ~ 32.6
Heated oxygen sensor (Bank 2 / Sensor 2) installation
3.5 ~ 4.5
34.3 ~ 44.1
25.3 ~ 32.6
Ignition coil installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Knock sensor [Bank 1] installation
1.9 ~ 2.4
18.6 ~ 23.5
13.7 ~ 17.4
Knock sensor [Bank 2] installation
1.9 ~ 2.4
18.6 ~ 23.5
13.7 ~ 17.4
Manifold absolute pressure sensor installation bolt
0.8 ~ 1.2
7.8 ~ 11.8
5.8 ~ 8.7
FUEL DELIVERY SYSTEM
Item
kgf·m
N·m
Ibf·ft
Fuel tank band mounting nuts
4.0 ~ 5.5
39.2 ~ 54.0
28.9 ~ 39.8
Fuel pump plate cover tightening
6.0 ~ 7.0
58.9 ~ 68.7
43.4 ~ 50.6
Sub fuel sender plate cover tightening
6.0 ~ 7.0
58.9 ~ 68.7
43.4 ~ 50.6
Delivery pipe installation bolts
0.9 ~ 1.4
8.8 ~ 13.7
6.5 ~ 10.1
Accelerator pedal module installation bolts
1.7 ~ 2.6
16.7 ~ 25.5
12.3 ~ 18.8
GENERAL
FLA -7
SPECIAL SERVICE TOOLS
E5DDDCC6
Tool
(Number and name)
Illustration
Application
09353-24100
Fuel Pressure Gauge
EFDA003A
Measuring the fuel line pressure
09353-38000
Fuel Pressure Gauge Adapter
BF1A025D
Connection between the delivery
pipe and fuel feed line
09353-24000
Fuel Pressure Gauge Connector
EFDA003C
Connection between Fuel Pressure
Gauge (09353-24100) and
Fuel Pressure Gauge Adapter
(09353-38000)
09310-2B100
Fuel Pump Plate Cover Wrench
SCMFL6666D
Removal of installation of fuel
pump plate cover
FLA -8
FUEL SYSTEM
REFERENCE SERVICE TOOLS (I) - WIRE
HARNESS REPAIR KIT II
Tool Number
Tool Name
TRK00A
Wiring Repair Kit
*For more information of the Wiring Repair Kit, please refer to BE group - "REFERENCE SERVICE TOOLS"
GENERAL
FLA -9
BASIC TROUBLESHOOTING
E726FCB8
BASIC TROUBLESHOOTING GUIDE
Bring Vehicle to Workshop
1
Perform troubleshooting procedure for DTC
11
Adjust or repair the vehicle
12
Confirmation test
13
END
14
Analyze Customer’s Problem
Ask the customer about the conditions and environment relative to the issue
(Use CUSTOMER PROBLEM ANALYSIS SHEET).
2
Confirm the Inspection Procedure for the System or Part
Using the SYMPTOM TROUBLESHOOTING GUIDE CHART, choose the correct inspection procedure for the system
or part to be checked.
4
Inspect Vehicle Visually
Go to Step 11, if you recognize the problem.
6
Recreate (Simulate) Symptoms of the DTC
Try to recreate or simulate the symptoms and conditions of the malfunction as described by customer.
If DTC(s) is/are displayed, simulate the condition according to troubleshooting procedure for the DTC.
7
Recreate (Simulate) Symptom
Try to recreate or simulate the condition of the malfunction as described by the customer.
9
Check the DTC
If DTC(s) does(do) not occur, refer to INTERMITTENT PROBLEM PROCEDURE in BASIC INSPECTION PROCEDURE.
If DTC(s) occur(s), go to Step 11.
10
Confirm Symptoms of Problem
If DTC(s) is/are not displayed, go to Step 9.
If DTC(s) is/are displayed, go to Step 11.
8
Verify Symptom, and then Check DTC and Freeze Frame Data
Connect Hi-Scan (Pro) to Diagnostic Link Connector (DLC).
Record the DTC and freeze frame data.
3
To erase DTC and freeze frame data, refer to Step 5.
Erase the DTC and Freeze Frame Data
5
NEVER erase DTC and freeze frame data before completing Step 2 MIL/DTC in "CUSTOMER PROBLEM
ANALYSIS SHEET".
NOTE
WARNING
LW8F1001
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст