Hyundai Santa Fe (2006 year). Manual — part 53
AT -164
AUTOMATIC TRANSAXLE (F4A51)
REMOVAL
E69F6B73
CAUTION
• Use a cover not to damage the vehicle sur-
face.
• Disconnect connectors carefully not to be
damaged.
NOTE
• Mark wires or hoses for identification.
1.
Remove the inter cooler and the engine cover. (see
EM group)
2.
Remove the battery (A).
A
SCMAT6001D
3.
Disconnect the AFS connector (A).
A
SCMAT6002D
4.
Lossen the clamp bolt (A) and disconnect the air
cleaner hose (B).
B
A
SCMAT6003D
5.
Remove the air cleaner upper cover (B) by removing
the clips (A).
B
A
SCMAT6004D
6.
Remove the air cleaner lower part (A) by removing the
two mounting bolts.
A
SCMAT6005D
AUTOMATIC TRANSAXLE SYSTEM
AT -165
7.
Remove the battery tray (B) by removing the four
mounting bolts (A).
A
B
SCMAT6006D
8.
Disconnect the transaxle wire harness connectors.
1)
Remove the inhibiter switch connector (A).
A
SCMAT6007D
2)
Remove the solenoid valve connector (A).
A
SCMAT6008D
3)
Remove the input speed sensor connector (A).
A
SCMAT6009D
4)
Remove the output speed sensor connector (A).
A
SCMAT6502L
5)
Remove the vehicle speed sensor connector (A).
A
SCMAT6011D
AT -166
AUTOMATIC TRANSAXLE (F4A51)
9.
Remove the control cable assembly(C) by removing
the nut (A) and clip (B).
A
C
B
SCMAT6012D
10. Disconnect the transaxle oil cooler hoses (B) from the
tubes by loosening the clamps (A).
A
B
SCMAT6013D
11. Remove the transaxle mounting bolts (A).
A
AKKF002O
12. Remove the starter motor by disconnecting the con-
nector. (see EE group)
13. Using the SST(09200-38001), hold the engine and
transaxle assembly safely.
09200-38001
SCMAT6503L
14. Remove the transaxle insulator mounting bolts (A).
A
SCMAT6504L
15. Remove the front wheels. (see SS group)
16. Lift up the vehicle.
17. Remove the power steering column joint bolt and the
EPS connector. (see ST group)
AUTOMATIC TRANSAXLE SYSTEM
AT -167
18. Remove the under cover (A).
A
SCMAT6505L
19. Drain the transaxle fluid.
20. Drain power steering fluid through the return tube(A).
(see ST group)
A
SCMAT6010L
21. Disconnect the power steering pressure tube (A) from
the power steering oil pump.
A
SCMAT6506L
22. Disconnect the lower arm, the tie rod end ball joint,
the stabilizer bar link from the front knuckle. (see SS
group)
23. Remove the roll stopper mounting bolts.
24. Remove the mounting bolts from the sub frame by
supporting the sub frame with a jack. (see SS group)
25. Remove drive shaft from transaxle. (see DS group).
26. Install a jack for supporting the transaxle assembly.
27. In case of 4WD, remove the transfer case assembly.
(see MT group’s ’Transfer case’)
28. Remove the drive plate bolts (A) and the transaxle
lower mounting bolts (B-4EA).
A
B
SCMAT6019D
29. Lifting the vehicle up and lowering the jack slowly, re-
move the transaxle assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст